Avaya 4606 User Manual
Size:
581.76 Kb
Download

The View Administrative Option

The View Administrative Option

If you are using static addressing and encounter problems, use the following procedure to verify the current values of system parameters and file versions.

Note:

Also use the ADDR option to view IP addresses. SeeStatic Addressing Installation inChapter 3: Local Administrative Options. The IP addresses might have been entered incorrectly. Verify whether you were provided with correct IP addresses.

The 4601 IP Telephone does not support the V I E W option.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 8 4 3 9 # (Mute V I E W #)

Note:

Press the Mute button momentarily. Do not press this key while pressing other keys. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

The following text displays left-justifiedat the top of the display:

View settings *=next #=exit

2.Press the * button at any time during viewing to display the next name and system value pair fromTable 1. The first pair returns after the last pair displays.

Press the # button at any time during viewing to terminate the procedure and restore the user interface to its previous state. The names and values display in the following order:

Table 1: Parameter Values

Name

System Value

Format

 

 

 

Model

46ccDccc

Up to 8 ASCII graphics characters.

 

 

 

Market

domestic

Only one value displays.

 

export

 

 

 

 

Phone SN

cccccccccccc

Phone Serial Number, up to 18 ASCII

 

cccccccc

graphic characters.

 

 

 

 

 

1 of 2

 

 

 

Issue 2.2 April 2005 65

Troubleshooting Guidelines

 

 

 

Table 1: Parameter Values (continued)

 

 

 

 

 

 

Name

System Value

Format

 

 

 

 

 

PWB SN

cccccccccccc

Printed Wiring Board (circuit board)

 

 

cccccccc

Serial Number, up to 18 ASCII

 

 

 

graphic characters.

 

 

 

 

 

PWB

ccccccccc

9 ASCII numbered characters.

 

comcode

 

 

 

 

 

 

 

MAC

00:60:1D:hh:hh:hh

Each octet of the MAC address

 

address

 

displays as a pair of hexadecimal

 

 

 

numbers.

 

 

 

 

 

L2 tagging

ccccccccc

Up to 9 ASCII characters.

 

 

 

 

 

VLAN ID

cccc

Up to 4 ASCII characters. Value is ID

 

 

 

number or “none.”

 

 

 

 

 

IP address

nnn.nnn.nnn.nnn

Up to 15 ASCII characters.

 

 

 

 

 

Subnet mask

nnn.nnn.nnn.nnn

Up to 15 ASCII characters.

 

 

 

 

 

Router

nnn.nnn.nnn.nnn

Up to 15 ASCII characters.

 

 

 

 

 

File server

nnn.nnn.nnn.nnn.nnnnn

Up to 21 ASCII characters: IP

 

 

 

address and port of last file server

 

 

 

used successfully.

 

 

 

 

 

Media server

nnn.nnn.nnn.nnn.nnnnn

Up to 21 ASCII characters: IP

 

 

 

address and port of media server

 

 

 

currently in use.

 

 

 

 

 

Group

nnn

Up to 3 ASCII characters.

 

 

 

 

 

Protocol

cccccccc

Up to 8 ASCII characters.

 

 

filename1.exe

Up to 16 ASCII graphic characters.

 

 

filename2.exe

Out of the box, there is only one

 

 

 

filename.exe. After installation, there

should be two filenames. If there is only one filename, installation has failed. Verify the problem and then reinstall the telephone.

2 of 2

66 4600 Series IP Telephone Release 2.2 Installation Guide

Error and Status Messages

Error and Status Messages

Note:

This section describes error and status messages only for those IP telephones having a display. For error and status messages related to installing a 4601 IP Telephone, see Troubleshooting the 4601 IP Telephone on page 71.

The 4600 Series IP Telephones issue messages in English only. The IP telephones also display messages from the switch, which can issue messages in the local language outside the United States.

Most of the messages in Table 2 display only for about 30 seconds, and then the telephone resets. The most common exception isExtension in Use, which requires manual intervention.

Table 2: Possible Error and Status Messages During Installation of 4600 Series IP Telephones

Message

Cause/Resolution

 

 

Bad Router

CAUSE: The telephone cannot find a router based on the information in

 

the DHCP file for GIPADD.

 

RESOLUTION: Change administration on DHCP, as indicated in the

 

4600 Series IP Telephone LAN Administrator Guide.

 

 

Checksum error

CAUSE: Downloaded application file was not downloaded or saved

 

correctly.

 

RESOLUTION: The telephone automatically resets and attempts to

 

re-initialize.

 

 

DHCP: CONFLICT

CAUSE: At least one of the IP address offered by the DHCP server

* to program

conflicts with another address.

 

RESOLUTION: Review DHCP server administration to identify duplicate

 

IP address(es).

 

 

Discover

CAUSE: The 46xx telephone is attempting to discover (and register

aaa.bbb.ccc.ddd

with) the gatekeeper at IP address aaa.bbb.ccc.ddd.

 

RESOLUTION: If this message appears for more than a few seconds,

 

especially if the IP address keeps changing, the telephone is unable to

 

contact the gatekeeper. Have the LAN Administrator verify network

 

connectivity between the telephone and the gatekeeper. Alternately,

 

revise the gatekeeper addresses in the DHCP/TFTP files in accordance

 

with the 4600 Series IP Telephone LAN Administrator Guideto point to

 

different gatekeepers.

 

 

 

1 of 4

 

 

Issue 2.2 April 2005 67

Troubleshooting Guidelines

Table 2: Possible Error and Status Messages During Installation of 4600 Series IP Telephones (continued)

Message

Cause/Resolution

 

 

Discovering...

CAUSE: The 46xx telephone is attempting to find a DHCP server.

 

RESOLUTION: If this message appears for more than a few seconds,

 

verify with the LAN Administrator that a DHCP server is appropriately

 

administered on the network. If there is not supposed to be a DHCP

 

server, you must “break into” the Discovering process and use static

 

addressing. See Static Addressing Installation on page 39. To break into

 

the Discovering process, press the # button, and when you see the

 

“100Mbs” or “10Mbs” message, quickly press the* (asterisk) button.

 

 

Extension

CAUSE: The PBX does not recognize the extension entered.

Error

RESOLUTION: Confirm the extension is correct and is correctly

 

administered on the switch. Then try registration again, taking particular

 

care to enter the extension accurately.

 

 

Extension in

CAUSE: The PBX detects an extension conflict with an existing set or

Use

Softphone.

 

RESOLUTION: You can force the current telephone to register, and

 

thereby disconnect the other user, by pressing #. The 4600 Series IP

 

Telephone prompts you again for the Extension and Password. If you

 

enter the same Extension and Password, you are asked to confirm that

 

you want to unregister the original user. Press # to unregister the original

 

user and to register the current phone. Then press * to reset the phone

 

and enter a different Extension and Password.

 

 

Failed to set

CAUSE: The 4600 Series Telephone was originally installed on one

phone IP

switch with static addressing, and has subsequently been installed on

address

another switch with an active DHCP server assigning dynamic IP

 

addresses.

 

RESOLUTION: Reset the telephone.

 

 

File too large Cannot save file

CAUSE: The telephone does not have sufficient room to store the downloaded file.

RESOLUTION: Verify the proper filename is administered in the TFTP script file, and that the proper application file is located in the appropriate location on the TFTP server.

Gateway Error

CAUSE: DEFINITY Release 8.4 does not have an H.323 station

 

extension for this telephone.

 

RESOLUTION: On the station administration screen, ensure the DCP

 

set being aliased for this IP telephone has an H.323 station extension

 

administered, in accordance with switch administration instructions.

 

 

Hardware

CAUSE: Hardware failure prevented downloading of application file.

failure

RESOLUTION: Replace telephone.

 

 

 

2 of 4

 

 

68 4600 Series IP Telephone Release 2.2 Installation Guide

Error and Status Messages

Table 2: Possible Error and Status Messages During Installation of 4600 Series IP Telephones (continued)

Message

Cause/Resolution

 

 

Incompatible

CAUSE: This release of DEFINITY does not support the current version

 

of the IP telephone.

 

RESOLUTION: Upgrade to the current version of Avaya

 

Communication Manager software.

 

 

IP Address in

CAUSE: The telephone has detected an IP address conflict.

use by another

RESOLUTION: Verify administration to identify duplicate IP

 

address(es).

 

 

NAPT Error

CAUSE: A device between the telephone and the call server is invoking

 

Network Address Port Translation, which the 4600 Series IP Telephones

 

do not support.

 

RESOLUTION: Contact the System Administrator to remove or

 

re-administerthe device.

 

 

No Ethernet

CAUSE: When first plugged in, the IP telephone is unable to

 

communicate with the Ethernet.

 

RESOLUTION: Verify the connection to the Ethernet jack, verify the jack

 

is Category 5, verify power is applied on the LAN to that jack, etc. Note

 

that if the telephone is attached to a 30A switched hub, upon loss of

 

Ethernet connectivity the usual No Ethernet message is not

 

displayed.

 

 

No file server

CAUSE: The TFTP server IP address in the IP telephone’s memory is

address

all zeroes.

 

RESOLUTION: Depending on the specific requirements of your

 

network, this may not be an error. If appropriate, either administer the

 

DHCP server with the proper address of the TFTP server, or administer

 

the telephone locally using the ADDR option. The ADDR option is

 

explained in Chapter 3: Local Administrative Options.

 

 

No Socket

CAUSE: The telephone has registered with the call server, but network

 

problems have prevented the telephone from opening a TCP socket.

 

Note: This message only occurs on older software versions; telephones

 

with newer software automatically reset.

 

RESOLUTION: Press the# button to have the telephone reset, and

 

contact the System Administrator to report the network problem.

 

 

Password Error

CAUSE: The PBX does not recognize the password entered.

 

RESOLUTION: Confirm the password is correct, then try registration

 

again, taking particular care to enter the password accurately.

 

 

 

3 of 4

 

 

Issue 2.2 April 2005 69

Troubleshooting Guidelines

Table 2: Possible Error and Status Messages During Installation of 4600 Series IP Telephones (continued)

Message

Cause/Resolution

 

 

System busy CAUSE: Most likely, the number of IP endpoints on the PBX is already at maximum, Less likely, network resource is unavailable.

RESOLUTION: The telephone was attempting to access a network resource (DHCP server, TFTP server, HTTP server, or the PBX) and was not successful. Check the resource being called upon for its availability. If the resource appears operational and properly linked to the network, verify that addressing is accurate and that a communication path exists in both directions between the telephone and the resource.

System Error CAUSE: The PBX has an unspecified problem.

RESOLUTION: Consult your Avaya Media Server administration and troubleshooting documentation.

Timeout Error CAUSE: Protocol timeout error.

RESOLUTION: Retry. If failure continues, check network congestion, addresses, etc. to identify cause of timeout.

Undefined

Error

Resource Error

CAUSE: The PBX has rejected registration for an unspecified reason.

RESOLUTION: Consult your Avaya Media Server administration and troubleshooting documentation.

CAUSE: The PBX rejects the registration request.

RESOLUTION: Verify administration to ensure the telephone’s proper IP address, extension, and password are being used.

Wrong Set Type CAUSE: The PBX does not recognize the set type.

RESOLUTION: Ensure the PBX is properly administered to expect the appropriate telephone for the IP address and extension.

4 of 4

70 4600 Series IP Telephone Release 2.2 Installation Guide