Avaya 4606 User Manual
Size:
581.76 Kb
Download

Local Administrative Options

Group Identifier

Use the following procedure to set or change the Group Identifier.

Note:

Perform this procedure only if the LAN Administrator instructs you to do so. The 4601 IP Telephone does not support the Group Identifier.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 4 7 6 8 7 (Mute G R O U P)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

The following text displays left-justifiedat the top of the display:

Group=ddd

New=_

where ddd is the Group value.

2.Enter a valid Group value(0-999).

If a value different from the current Group value is entered, the following text displays left-justifiedat the top of the display:

Save new value?

*=no #=yes

3.Press the * button to terminate the procedure, or the# button to save the new value. If you press the# button, the following text displays:

New value being saved

The new value is saved and the user interface is restored to its previous state.

48 4600 Series IP Telephone Release 2.2 Installation Guide

Computer-TelephonyIntegration (CTI) Enable/Disable

Computer-TelephonyIntegration (CTI) Enable/Disable

Use the following procedure to enable or disable the CTI interface.

Note:

The default for the CTI interface is enabled.

The 4601, 4602, 4602SW, and 4690 do not support the CTI interface.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 2 8 4 # (Mute C T I #)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

One of the following texts displays left-justifiedat the top of the display, depending on the current value of the CTI:

If CTI=manual:

CTI=manual

 

0=Off #=OK

If CTI=disabled:

 

 

CTI=disabled

 

1=Manual #=OK

 

 

2.Press the 1 or0 button to enable or disable the CTI interface respectively, or the# button to leave the current value. The following text displaysleft-justifiedat the top of the display:

UDP Port=497xx

New=_

where 497xx is the value of the UDP port for CTI.

3.Enter a valid value between 49714 and 49721, inclusive for the UDP Port for CTI. The following text displaysleft-justifiedat the top of the display:

Save new value? *=no #=yes

Issue 2.2 April 2005 49

Local Administrative Options

4.Press the * button to terminate the procedure, or the# button to save the new values. If you press the# button, the following text displays.

New value being saved

The new values are saved, and the user interface is restored to its previous state.

Site-SpecificOption Number Setting

! CAUTION:

Do not perform this procedure if you are using static addressing. Perform this procedureonly if you are using DHCPand the LAN administrator instructs you to do this.

Use the following procedure to set the Site-SpecificOption Number (SSON).

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 7 7 6 6 # (Mute S S O N #)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

All IP telephones except the 4601 display the following text left-justifiedat the top of the display:

SSON=ddd

New=_

where ddd is the value of SSON.

Because it does not have a display, the 4601 IP Telephone’s Call Appearance Line indicators wink out the current SSON value. Call Appearance Line a represents the SSON’s first digit. Call Appearance Lineb represents the SSON’s second digit, and Call Appearance Linea represents the SSON’s third digit. For each digit, the applicable indicator winks the number of times represented by the current SSON value 600 milliseconds on, 200 milliseconds off. An 1800 millisecond pause occurs before changing indicators. If the current value is zero, the appropriate Call Appearance Line indicator flutters five times 50 milliseconds on, 50 milliseconds off instead of winking.

50 4600 Series IP Telephone Release 2.2 Installation Guide

Reset System Values

After the 4601 “displays” the current SSON, the Message Waiting indicator at the top of the phone and the Message button LED on the faceplate flash 500 milliseconds on, 500 milliseconds off to indicate an entry is expected.

2.Enter a valid value between 128 and 255 for the SSON.

The 4601 provides feedback as you enter each digit using both Call Appearance Line indicators. The indicators alternate winking the number of times represented by the digit you press 200 milliseconds on, 50 milliseconds off. For example, if the SSON’s first digit is “2,” pressing number2 on the dial pad causes Call Appearance Linea’s indicator to wink two times. If the second digit you press is “4,” after an 1800 millisecond pause, Call Appearance Lineb’s indicator winks four times. Pressing “0” (zero) on the dial pad causes the appropriate indicator to flutter three five 50 milliseconds on, 50 milliseconds off.

Then the 4601 flashes both Message Waiting indicators 500 milliseconds on, 500 milliseconds off to indicate an entry is expected.

For all IP telephones except the 4601, if a value different from the current SSON value is entered, the following text displays left-justifiedat the top of the display:

Save new value? *=no #=yes

3.Press the * button to terminate the procedure, or the# button to save the new value. If you press the# button, all IP telephones except the 4601 display the following text:

New value being saved

All phones save the new value, and restore the user interface to its previous state.

Reset System Values

Use the following procedure to reset all system initialization values to the application software default values.

! CAUTION:

This procedure erases all static information, without any possibility of recovering the data.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 7 3 7 3 8 # (Mute R E S E T #)

Issue 2.2 April 2005 51

Local Administrative Options

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

The 4601 IP Telephone flashes both Message Waiting indicators 500 milliseconds on, 500 milliseconds off to indicate user input is expected. All other IP telephones display the following text left-justifiedat the top of the display:

Reset values? *=no #=yes

! CAUTION:

As soon as you press the # button, all static information will be erased, without any possibility of recovering the data.

2.If you do not want to reset the system values, press * (no) and proceed to Step 4.

Pressing the pound sign (#) to reset the system values on a 4601 IP Telephone produces a confirmation tone. The 4601’s Message Waiting indicators illuminate, but do not flash, to indicate no entry is allowed while the system values are being reset. All other phones display a screen with the following prompt on the top line:

Are you sure? *=no #=yes

3.Press the * button to continue without resetting the values and proceed to Step 4. Or, press the# button to reset values to their defaults.

All phones except the 4601 display the following text left-justifiedat the top of the display while the system values are reset to defaults:

Resetting values.

The telephone resets from the beginning of registration, which takes a few minutes.

4.If you do not reset the phone, all IP telephones except the 4601 display the following prompt:

Restart phone?

*=no #=yes

5.Press the * key to terminate the procedure without restarting the telephone. Otherwise, press# and perform the following Restart procedure.

52 4600 Series IP Telephone Release 2.2 Installation Guide