Avaya 4606 User Manual
Size:
581.76 Kb
Download

About Local Administrative Procedures

If

Then (continued)

In certain procedures, for example, SSON or to display the extension number, a value already exists and you press the # button to indicate you either want to enter a new value or have the current value displayed

User input is not allowed for example, during processing

The telephone’s boot image is in the process of being upgraded

An error beep tone sounds

The Message Waiting indicator at the top of the phone and the Message button’s LED on the faceplate are lit but not flashing. Call Appearance Line a alternating with line b after an 1800 millisecond pause, if the value has more than one digit winks 600 milliseconds on, 200 milliseconds offn times for digitn to indicate the current value. The appropriate Call Appearance Line indicator flutters five times to indicate the digit zero. After feedback of the current value, the Message Waiting indicator at the top of the phone and the Message button’s LED flash 500 milliseconds on, 500 milliseconds off to indicate user input is expected/required.

The Message Waiting indicator at the top of the phone and the Message button LED on the faceplate are steadily lit.

All LEDs, meaning Call Appearance Lines a andb, and both Message indicators, light steadily during the download process.

An invalid button was pressed. Try again.

2 of 2

About Local Administrative Procedures

Local administrative procedures allow you to customize the 4600 Series IP Telephone installation for your specific operating environment. This section provides a description of each local administrative option covered in this guide, with references to the pages on which the option appears.

Local Programming Option

Code

See

 

 

 

Static addressing

A D D R (2 3 3 7)

Static Addressing

 

 

Installation on page 39

 

 

 

Quality of Service options

Q O S (7 6 7)

QoS Option Setting on

 

 

page 43

 

 

 

PC Ethernet Interface

I N T (4 6 8)

Interface Control on

 

 

page 45

 

 

 

 

 

1 of 2

 

 

 

Issue 2.2 April 2005 37

Local Administrative Options

Local Programming Option

Code

See

 

 

 

Group Identifier

G R O U P (4 7 6 8 7)

Group Identifier on

(Release 2.0 and later only)

 

page 48

 

 

 

Computer-Telephony

C T I (2 8 4)

Computer-Telephony

Integration

 

Integration (CTI) Enable/

 

 

Disable on page 49

 

 

 

Site-SpecificOption Number

S S O N (7 7 6 6)

Site-Specific Option

 

 

Number Setting on

 

 

page 50

 

 

 

Reset the telephone

R E S E T (7 3 7 3 8)

Reset System Values on

 

 

page 51

 

 

 

Restart the telephone

R E S E T (7 3 7 3 8)

Restart the

 

 

Telephone on page 53

 

 

 

Signaling protocol identifier

S I G (7 4 4)

Signaling Protocol

(Release 2.0 and later only)

 

Identifier on page 54

 

 

 

Test the telephone

T E S T (8 3 7 8)

Self-Test Procedure on

 

 

page 56

 

 

 

Clear values to factory defaults

C L E A R (2 5 3 2 7)

Clear Procedure on

 

 

page 57

 

 

 

Visual Alerting mode control

A L E R T (2 5 3 7 8)

Visual/Audible Alerting

 

 

Procedure on page 58

 

 

 

DHCP chaddr field value

C H A D D R (2 4 2 3 3 7)

Manually Setting the

 

 

DHCP Client Hardware

 

 

Address on page 59

 

 

 

Layer 2 frame tagging control

T A G (8 2 4)

Setting L2Q Tagging

(4601 only)

 

Control (4601 Only) on

 

 

page 61

 

 

 

 

 

2 of 2

 

 

 

38 4600 Series IP Telephone Release 2.2 Installation Guide

Pre-InstallationChecklist for Static Addressing

Pre-InstallationChecklist for Static Addressing

Before performing static addressing, verify that all the requirements listed in the Requirements to Verify about the Network section of thePre-Installation Checklist are met. You do not have to consider item4. on page 16, as it refers to the DHCP server. In addition, you must have the values for the following parameters. Failure to do so can cause data entry errors that prevent the telephone from working. Such errors can also have a negative impact on your network. Print copies of this checklist for each subnet.

1. The IP address of the media server/gatekeeper.

2. The transport layer port number of the address of the Management Complex (media server/gatekeeper). Although this can be a value between 0 and 65535, the default value is 1719.Do not change this value unless it conflicts with an existing port assignment.

3. The IP address of the gateway/router.

4. The IP netmask.

5. The IP address of the TFTP server.

Static Addressing Installation

The usual way to assign IP addresses to IP telephones is the automatic method described in Dynamic Addressing Process. There might be times, however, when manual assignment of IP addresses is desired.

! CAUTION:

Static addressing is necessary when a DHCP server is unavailable.

Because of the difficulties associated with static addressing, we very strongly recommend that a DHCP server be installed and static addressing avoided.

Issue 2.2 April 2005 39

Local Administrative Options

Note:

The displays on the 4602, 4602SW, 4610SW, 4612, 4620, 4620SW, 4621SW, 4622SW, 4624, 4625SW, 4630, 4630SW, and 4690 IP Telephones accommodate 24 characters per line. The display on the 4606 Telephone accommodates 16 characters per line. Here and in the procedures that follow, the example on the left shows the 4602, 4602SW, 4610SW, 4612, 4620, 4620SW, 4621SW, 4622SW, 4624, 4625SW, 4630, 4630SW, and 4690 Telephones’ display. The example on the right shows the 4606 Telephone’s display. Showing only one example means that example applies to all 4600 Series IP Telephones with displays.

The 4601 IP Telephone does not support static addressing.

Use the following procedure to invoke manual address information programming.

1. Start manual address programming by performing one of the following steps:

a.During normal DHCP processing, press the * key while “* to program“ displays during the DHCP process.

or

b.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 2 3 3 7 # (Mute A D D R #)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

The following message displays:

Phone=nnn.nnn.nnn.nnn

or

nnn.nnn.nnn.nnn

New=_

 

Phone=_

 

 

 

where nnn.nnn.nnn.nnn is the value of the telephone.

2.Enter the telephone’s IP address followed by the# button. The following message displays:

CallSv=nnn.nnn.nnn.nnn

or

 

nnn.nnn.nnn.nnn

New=_

 

 

CallSv=_

 

 

 

 

where nnn.nnn.nnn.nnn is the value of the media server/gatekeeper IP address.

40 4600 Series IP Telephone Release 2.2 Installation Guide

Static Addressing Installation

3.Enter the Gatekeeper IP address followed by the# button. The following message displays:

CallSvPort=nnnnn

New=_

where nnnnn is the value of the Management Complex (media server/gatekeeper)transport-layerport number, a value between 0 and 65535.

4.Enter the appropriate value for the Port Number followed by the# button. The following message displays:

Router=nnn.nnn.nnn.nnn

or

 

nnn.nnn.nnn.nnn

New=_

 

 

Router=_

 

 

 

 

where nnn.nnn.nnn.nnn is the value of the gateway/router IP address.

5.Enter the Gateway router IP address followed by the# button. The following message displays:

Mask=nnn.nnn.nnn.nnn

or

 

nnn.nnn.nnn.nnn

New=_

 

 

Mask=_

 

 

 

 

where nnn.nnn.nnn.nnn is the value of the IP netmask.

6.Enter the IP netmask followed by the# button. The following message displays:

FileSv=nnn.nnn.nnn.nnn

or

 

nnn.nnn.nnn.nnn

New=_

 

 

FileSv=_

 

 

 

 

where nnn.nnn.nnn.nnn is the value of the TFTP server IP address.

7.Enter the TFTP Server IP address followed by the# button.

One of the following texts displays left-justifiedat the top of the display, depending on the current status of 802.1Q:

If 802.1Q is off:

802.1Q=off

 

1=on #=OK

If 802.1Q is on:

 

 

802.1Q=on

 

0=off #=OK

 

 

8.Press the 1 or0 button to turn802.1Q on or off respectively. The display is updated to show the current status of 802.1Q.

Issue 2.2 April 2005 41

Local Administrative Options

9.Press the # button to continue the procedure without changing the displayed status of 802.1Q

The following text displays left-justifiedat the top of the display:

VLAN ID=dddd

New=_

where dddd is the value of the 802.1 VLAN ID.

10.Enter a valid value between 0 and 4094 for the new value of the 802.1 VLAN ID. The following message displays:

VLAN test=ddd

New=_

where ddd is the value of theDHCPOFFER wait period.

11. Enter a valid value between 0 and 999 for the new value of the DHCPOFFER wait period.

The following message displays:

Save new values? *=no #=yes

12.Press the # button to save the new values you entered. The following message displays:

New values being saved

Once the new values are stored, the telephone is reset.

If a new boot program is downloaded from the TFTP server after you enter static addressing information, you must reenter your static addressing information.

42 4600 Series IP Telephone Release 2.2 Installation Guide