Audiovox ACC-30 User Manual

Size:
186.13 Kb
Download

6

COMPACT

ACC-30

DIGITAL AUDIO 6 DISC

COMPACT DISC CHANGER

MODEL ACC-30

6-DISCCD CHANGER

INSTALLATION MANUAL

PACKING LIST

MAIN UNIT

Changer

6

COMPACT

ACC-30

DIGITAL AUDIO 6 DISC

COMPACT DISC CHANGER

INSTALLATION PARTS

 

Hex Head Bolt with Washer Base

Phillips Head

Mounting Bracket

(M5 x 12)

Screw

2 pcs.

4 pcs.

4 pcs.

 

Mounting Angle Adjustment Tool

Screw Hole Cover Labels

5 Meter Din Cable

 

 

1 pc.

1 pc.

 

1 pc.

ACCESSORIES

CD Magazine

Index seal sheet

Installation Manual

Owner's guide

1 pc.

1 pc.

1 pc.

1 pc.

1

BEFORE INSTALLING THE UNIT

Transport Lock Screws

The mechanism in the CD changer is "locked" into place during shipment by the 4 transport screws. Be sure to remove the screws prior to installation.

Retain these screws for future use when transporting the unit for service/maintenance. l Caution l

After removing the transport lock screws, place the supplied seals over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction.

Installation and Wiring Precautions

1

To prevent a short-circuit,

 

l Be sure to turn off the ignition and remove the negative (-)battery cable, prior to installation.

 

l Connect power wires last.

 

Note

 

If the changer is to be installed in a car that is equipped with an on-boarddrive or navigation computer, do not disconnect

 

the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra

 

caution during installation, not to cause a short circuit.

2

Do not install the unit in the following locations.

 

l Locations exposed to direct sunlight.

 

l Where hot air is discharged from the car heater.

 

l In areas subject to extreme temperatures.

3

Incorrect installation can cause the sound to "skip" when playing a disc.

 

Mount the unit firmly in place, using the supplied brackets and screws.

4

5

Be careful not to damage the car wiring.

l Be sure to use the supplied screws.

lBe careful not to snag any wires when tightening screws.

lDo not use any of the screws that are part of the brake or steering system, to install the unit.

6

l This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning

 

of the mechanism.

2

INSTALLATION

The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-inanti-vibrationsprings (lef t and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, theanti-vibrationcompensation will not be effective and vibration may cause the disc to skip.

HORIZONTAL INSTALLATION

Set the anti-vibrationsprings to position "H".

position "H"

45° H

V

VERTICAL INSTALLAITON

Set the anti-vibrationsprings to position "V".

position "V"

V

45°

H

45° ANGLE INSTALLATION

Set the anti-vibrationsprings to position "45°".

position "45°"

V

45°

H

 

45°

PROCEDURE FOR HORIZONTAL INSTALLATION

1 Attach a mounting bracket to each side of the unit, using the 4 hex head bolts with washer base.

45° H

V

Bracket

NOTE: Make sureanti-vibrationsprings are set to position "H".

2 Determine the mounting location, and drill four mounting holes.

NOTE: If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from catching on carpet. Cut holes in carpet before drilling intosub-surface.

Never mount the unit near the fuel tank.

3 Secure the unit in place, using fourself-tappingPhillips head screws.

Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion.

Bracket

Bracket

Hex head bolt

with washer base

 

Drill holes 1/8" (4mm) in diameter.

Self-tappingPhillips head screw

Bracket

3

PROCEDURE FOR VERTICAL INSTALLATION

Note

If the anti-vibrationspring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2.

1

Set the anti-vibrationsprings to position "V".

position "V"

V

45°

H

2

Attach a mounting bracket to each side of the unit, using

 

the hex head bolts with washer base.

 

Bracket

Bracket

Hex head bolt with washer base

3

Determine the mounting location, and drill four mounting

4

Mount the unit in place, using four self-tappingPhillips head

 

holes.

 

screws.

 

 

 

 

 

Use RTV (silicone sealer) on screw threads or around

 

 

 

 

 

the holes to prevent moisture intrusion.

 

NOTE: If mounting surface is carpeted, use caution

 

 

 

when drilling holes to prevent drill bit from

 

 

 

catching on carpet. Cut holes in carpet

 

 

 

before drilling into sub-surface.

Self-tapping

 

 

 

 

 

 

 

 

 

 

Phillips head

 

 

Never mount the unit near the fuel tank.

 

 

 

 

 

 

screw

 

 

 

 

 

Bracket

Bracket

Drill holes 1/8" (4mm) in diameter

4

PROCEDURE FOR 45° ANGLE INSTALLATION

Note

If the anti-vibrationspring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2.

1

Set the anti-vibrationsprings to position "45°".

position "45°"

 

45°

V

H

45°

2

Attach a mounting bracket to each side of the unit, using

 

the 4 hex head bolts with washer base.

 

Bracket

Bracket

Hex head bolt with washer base

3

Determine the mounting location, and drill four mounting

4

Mount the unit in place, using four self-tappingPhillips head

 

holes.

 

screws.

 

 

 

 

 

Use RTV (silicone sealer) on screw threads or around

 

NOTE: If mounting surface is carpeted, use caution

the holes to prevent moisture intrusion.

 

 

when drilling holes to prevent drill bit from

 

 

 

catching on carpet. Cut holes in carpet

Self-tappingPhillips head screw

 

 

before drilling into sub-surface.

 

 

 

 

 

 

 

 

Never mount the unit near the fuel tank.

 

 

 

 

 

 

 

 

 

Bracket

Bracket

Drill holes 1/8" (4mm) in diameter

5

WIRING

Mating 8-pinDIN socket on rear of compatible radio chassis (seeNote below).

Car Stereo with

CD Changer Controls

DIN

cable

 

 

 

(8

 

 

 

 

 

 

-

 

 

 

pin)

CD changer

NOTE: 1. Check with your Rampage/Audiovox audio dealer to be sure your stereo is directly compatible with this CD changer.

2.When used with Rampage model AV-427car stereo, be sure Changer Selector switch on bottom

of radio chassis is set to position "B".

6

© 1999 Audiovox Corporation, Happauge, N.Y. 11788

Printed in Korea

128-5572