1 |
USER’S MANUAL |
|
|
|
Part 2 |
Tapeless Digital Answering System with Time/Day 1717
Fold open this manual for information about this product’s installation and operation. Please also read
Part 1 – Important Product Information.
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
© 2000 Advanced AmericanTelephones. All rights reserved. Printed in Mexico. 850002593 Issue 1AT&T 5/00
I N S T A L L A T I O N
TEL LINE |
TEL SET |
Strain |
|
Telephone |
Relief Tab |
|
|
|
Set Cord |
|
|
|
|
|
Standard |
Modular |
|
Telephone |
|
|
Electrical |
|
|
Jack |
|
|
Outlet |
|
|
|
Power Cord |
Telephone Line Cord |
|
1Connect the telephone line cord.
Plug one end of the telephone line cord into the jack labeled TEL LINE on the back of the system. Plug the other end into a modular telephone jack.
2Connect the telephone.
NOTE: If you do not want to connect a telephone, skip to Step 3.
Plug the telephone set cord from the telephone into the jack labeled TEL SET on the back of the system.
3Connect the power cord.
Plug the power cord into the jack labeled POWER and into an electrical outlet not controlled by a wall switch. Fit the power cord behind the strain relief tab. The Message Window flashes C to indicate that you need to set the clock.
Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. Input: 120V, 60 Hz.
Output: 9V AC, 400 mA.
1
O P E R A T I O N
Set and hear time/day
Use with other buttons to change/hear settings
Turn system on or off
Record a memo /
Repeat all or part of a message
Displays number |
of messages and |
other information |
Adjust volume |
Delete all |
or selected |
messages |
Record and play |
outgoing announcement / |
Skip all or part of a message |
Microphone |
Play/Stop messages
PLAY Light indicates messages
Setting the Clock
You’ll need to set the clock so that it can announce the day and time that each message is received. Press Pto exit Setting the Clock at any time.
1Press and hold Cuntil the Message Window displays C, and the default day is announced.
2To change the day setting, hold down 
or 
until the correct day is announced. Then release the button.
3Press and release C. The current hour setting is announced.
4To change the hour setting, hold down 
or 
until the correct hour is announced. Then release the button.
5Press and release C. The current minutes setting is announced.
6To change the minutes setting, hold down 
or 
until the correct minutes setting is announced. Then release the button.
7Press and release C. The new day and time are announced.
To check the clock, press and release
C.
NOTE: In the event of a power failure, see the instructions on the bottom of the unit to reset the clock.
Recording Your Announcement
Before using this answering system, you should record the announcement (up to one minute long) that callers will hear when the system answers a call. If you choose not to record an announcement, the system answers with a prerecorded announcement:“Hello. Please leave a message after the tone.”
1Press and hold 
. The system beeps. Speak toward the microphone normally, from about nine inches away. While you are recording, the Message Window displays — .
2To stop recording, release 
. The system automatically plays back your announcement.
To review your announcement, press and release 
.
Turning the System On/Off
Use Oto turn the system on and off. When the system is off, the Message Window is blank.
Volume Control
Use volume buttons (+and -) to adjust the volume of the system’s speaker. Press the top button (+) to increase volume. Press the bottom button (-) to decrease volume. The system beeps three times when you reach the maximum or minimum volume setting.
2
Loading...