Atlantis Land A05-19BM-D02 User Manual
IMPORTANT SAFETY INSTRUCTIONS
Cleaning the TFT LCD Monitor
Federal Communications Commission (FCC) Statement
INSTALLING THE MONITOR
Installing the Base
Installing the Monitor
Input Select (only for
DISPLAY MODES MEMORY
User Setting Area
Factory Presetting Area
POWER SAVING FEATURE
PRIMA DI INIZIARE
Pulizia del pannello LCD
Comunicato relativo alle interferenze Radio
Precauzioni per il cavo di alimentazione
INSTALLAZIONE DEL MONITOR
Installare la base
Installazione del monitor
FUNZIONI DI CONTROLLO
SELEZIONE DELLA FUNZIONE
Selezione ingresso (solo per
3 - 40
MEMORIA MODALITÀ SCHERMO
Area Impostazioni dell’Utente
Area Impostazioni di Fabbrica
PIEDINATURA DEL CAVO SEGNALE VGA
FUNZIONI PER IL RISPARMIO ENERGETICO
REGOLAZIONE DEL TEMPO
AVANT DE COMMENCER
Propreté du panneau LCD
communiqué relatif aux interférences Radio
Précautions pour le câble d'alimentation
Installer le Socle
Installer le Moniteur
FONCTIONS DE CONTROLE
SELECTION DE FONCTIONS
Sélectionne du signal entrant (seulement pour
FONCTIONS DU MICRO REGLAGE
Sauvegarde des modes d’affichage
Réglage par l’Utilisateur
DISPOSITION DES BROCHES DU CONNECTEUR DE SIGNAL VGA
CARACTERISTIQUE D'ECONOMIE D'ENERGIE
DEFINITIONS DU TEMPS
WARRANTY CERTIFICATE CONDIZIONI DI GARANZIA CERTIFICAT DE GARANTIE
WARRANTY - GARANZIA - GARANTIE
CERTIFICATO DI GARANZIA
CERTIFICAT DE GARANTIE
4 - 40
Important Safety Instructions
•Read the Safety Instructions carefully and keep it for later use.
•Be aware of all warnings and instruction signs marked on the products.
•When cleaning, turn off the electrical supply at all times. Never use liquid or aerosol detergent, use a damp rag instead. For more details, please refer to Pag. 6 “Cleaning the Monitor.”
•Always keep the product away from heavy moisture.
•Keep this product stable all times. The product may fall causing serious damage.
•Do not clog apertures on the bezels used for ventilation purpose. Do not install this product in poor ventilated areas. Always keep this product away from all kinds of heat sources.
•The power source used for this product must match one marked on the product's label. Please consult your dealer if you have any doubt.
•In order to avoid electric shock, a
•Do not lay the power cord in a pathway or rest anything heavy on it.
•Do not insert objects or pour liquid into this product through apertures on bezels. It may touch a high voltage area causing an electric shock or short circuit.
•Do not attempt to repair the product by yourself. It may expose you to electric shock. Contact a dealer near you for service.
•Do not plug the power cord in under the following circumstances. A qualified field service electrician is needed.
•When the power cord is damaged or frayed.
•If liquid has been poured into the product.
•If the product has been exposed to rain or heavy moisture.
•If the product can't be adjusted and operated properly by following the operative instructions. Intent to do more advanced adjustments may result in extensive work for field service electrician.
•If the product has been dropped or the casting is broken.
•If there is a dramatic change of the performance.
•A proper type of power cord has been selected according to the safety of destination and must be used to prevent electric shock.
1 Getting Started
Congratulations on your purchase of a TFT LCD Color Monitor. This section lists package contents, features, precautions, as well as cleaning and installation instructions.
IMPORTANT! PLEASE KEEP THE ORIGINAL BOX AND ALL PACKING MATERIAL FOR FUTURE SHIPPING NEEDS.
•Sit at least 18"(45 cm) away from the screen when in use.
•Do not touch the LCD panel with your bare hands. Oil from your skin is difficult to remove and may damage the screen.
•Do not expose the LCD monitor directly under sunlight or other heat sources. When in use, the LCD screen should be facing away from light sources to reduce glare.
•It is important to choose a
•Ensure the area around the LCD monitor is clean and
•Do not place heavy objects on the power cord, adapter, or signal cables.
•If smoke, abnormal noise, or strange odor occurs, immediately turn the LCD monitor off and call your dealer. Do not continue using the LCD monitor.
•Do not remove the rear cover by yourself. The display unit contains
5 - 40
•When moving, always handle your LCD monitor with care.
•Do not forcefully press down against the LCD display as this will damage the monitor.
1.2 Cleaning the TFT LCD Monitor
• Wipe the screen gently with a clean camel hairbrush, or a soft, clean,
• Never pour or spray any liquid onto the LCD monitor
• Do not apply pressure to the LCD panel.
1.3 Federal Communications Commission (FCC)
This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
2 Installing the Monitor
Open the shipping cartons and check the contents.
If any items are missing or damaged, contact your dealer immediately.
The package should include the following items:
•TFT color monitor
•DC power adapter
2.2Installing the Base
Follow these steps to install the base:
1.Turn the monitor down.
2.Assembly the base to the arm with screw.
3.Tie the screw with a coin.
2.3Installing the Monitor
This monitor is equipped with an auto sensing DC power adapter for voltage ranges
1.Before you connect the cables, made sure that the monitor and the system uni power switches are off.
2.Plug one end of the
6 - 40
3.Connect the DC power cord to the DC jack.
4.Connect the power cable.
3 Control Functions
The monitor digital control functions are located on the front panel. They are shown in the figure below and described in the following paragraphs.
1.Power Switch with Indicator LED
4 Function Select
With the U andV knobs, you can adjust the speakers volume.
Press the 1 knob to show the OSD menu. Than use the U andV knobs to select a function. Press the 2 knob to close the OSD menu. You can hold the 2 knob for more than 3 second to adjust the image quality automatically.
4.1Input Select (not for
Select the image signal coming from the VGA cable.
Select the image signal coming from DVI cable. (option)
Close the Signal Select OSD menu.
Adjust the luminance level in the image.
Adjust the difference in luminance between light and dark areas of the
Adjust the black Level in the image.
Close the Video OSD menu.
Adjust the volume of speakers
Adjust the speaker’s volume to right side or left side.
Close the Audio OSD menu
7 - 40
4.4.1 Color Temperature
Adjust the R.G.B. gain level.
Select color temperature to 6500°K.
Select color temperature to 9300°K.
Close the Color Temperature OSD menu.
4.4.2 Adjust the flesh tone of the image
Adjust the shade of the image color.
Adjust the saturation of the image color.
Close the Color OSD menu.
4.4.3 Image Adjust
Adjust geometry of the image automatically.
Adjust the horizontal sync size of signal.
Adjust the horizontal sync phase of signal.
Adjust the horizontal position of the image.
Adjust the vertical position of the image.
Close the Image OSD menu
Sets the language of the OSD windows.
4.6.1 OSD Controls
Setting the OSD menu display time.
OSD H. Position
OSD H. Position Adjust the horizontal position of the OSD menu.
OSD V. Position
OSD V. Position Adjust the vertical position of the OSD menu.
Close the OSD Control OSD menu
8 - 40
4.6.2Recall the factory default setting
Adjust the picture display more clear
Close the Tools OSD menu
Close the OSD menu
6 Display Modes Memory
6.1User Setting Area
The user setting area on the
6.2Factory Presetting Area
There are some preferred display modes preset in the
7 Signal Connector
To connect VGA, 8514A or
9 - 40
Serial Clock Input
8 Power Saving Feature
When the power saving active them the power indicator LED will be from Green Light to Amber, And power saving feature complies with these VESA power saving modes:
The monitor uses the H. Sync and V. Sync signals to determine the operation mode to enter.
9 Time Settings
Time settings are adjusted from the system unit by software. To fulfill the requirements in the NUTEK specification 803299/94 the total time from indicated inactivity to Power Saving position A2 (VESA OFF) must not be set more than 70 minutes. We recommend you switch off the monitor when you do not intend to use it for awhile.
17.0" (full 17.0" viewable diagonal area)
19.0" (full 17.0" viewable diagonal area)
TFT (Thin Film Transistor), Active Matrix Panel
170 H - 170 V
10 - 40