ASRock 865PE User Manual

0 (0)

ConRoe865PE

User Manual

Version 3.2

Published October 2006 Copyright©2006 ASRock INC. All rights reserved.

1

Copyright Notice:

No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

ASRock Website: http://www.asrock.com

2

Contents

1 Introduction ................................................... ...

5

1.1

Package Contents................................................................

5

1.2

Specifications .....................................................................

6

1.3

Motherboard Layout ...........................................................

9

1.4

ASRock 8CH I/O ..................................................................

10

2 Installation .............................................

11

2.1

Screw Holes ......................................................................

11

2.2

Pre-installation Precautions ................................................

11

2.3

CPU Installation ...................................................................

12

2.4

Installation of CPU Fan and Heatsink ..................................

14

2.5

Installation of Memory Modules (DIMM) ..............................

15

2.6

Expansion Slots (PCI and AGP Slots) .................................

17

2.7

Jumpers Setup ...................................................................

18

2.8

Onboard Headers and Connectors ....................................

19

2.9

Serial ATA (SATA) Hard Disks Installation ...........................

22

2.10

Driver Installation Guide ....................................................

22

2.11

Untied Overclocking Technology.........................................

22

3 BIOS SETUP UTILITY......................................

23

3.1

Introduction ..........................................................................

23

 

3.1.1

BIOS Menu Bar .........................................................

23

 

3.1.2

Navigation Keys .......................................................

24

3.2

Main Screen ........................................................................

24

3.3

Advanced Screen ...............................................................

24

 

3.3.1

CPU Configuration ....................................................

25

 

3.3.2

Chipset Configuration ...............................................

27

 

3.3.3

ACPI Configuration ...................................................

28

 

3.3.4

IDE Configuration ......................................................

29

 

3.3.5

PCIPnP Configuration ................................................

31

 

3.3.6

Floppy Configuration ................................................

32

 

3.3.7

Super IO Configuration .............................................

32

 

3.3.8

USB Configuration ....................................................

34

3.4

Hardware Health Event Monitoring Screen ........................

35

3.5

Boot Screen ........................................................................

36

 

3.5.1

Boot Settings Configuration .....................................

36

 

3.5.2

Boot Device Priority ..................................................

37

3.6

Security Screen ..................................................................

37

3.7

Exit Screen ..........................................................................

38

3

4 Software Support ...........................................

39

4.1

Install Operating System ...............................................

39

4.2

Support CD Information .................................................

39

 

4.2.1 Running Support CD ............................................

39

 

4.2.2 Drivers Menu ........................................................

39

 

4.2.3 Utilities Menu ........................................................

39

 

4.2.4 “LGA 775 CPU Installation Live Demo” Program ..

39

 

4.2.5 Contact Information .............................................

39

4

Chapter 1 Introduction

Thank you for purchasing ASRock ConRoe865PE motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by- step guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD.

Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com

1.1 Package Contents

ASRock ConRoe865PE Motherboard

(ATX Form Factor: 12.0-in x 9.0-in, 30.5 cm x 22.9 cm) ASRock ConRoe865PE Quick Installation Guide

ASRock ConRoe865PE Support CD

(including LGA 775 CPU Installation Live Demo) One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional) One ASRock 8CH I/O Shield

5

1.2Specifications

Platform

- ATX Form Factor: 12.0-in x 9.0-in, 30.5 cm x 22.9 cm

CPU

- LGA 775 for Intel® Dual Core Pentium® XE and Pentium® D /

 

Pentium® 4 / Celeron® D, supporting CoreTM 2 Duo Desktop

 

(Conroe), Presler and Cedar Mill processors (in 775-land

 

LGA package)

 

- FSB 1066/800/533 MHz (see CAUTION 1)

 

- Supports Hyper-Threading Technology (see CAUTION 2)

 

- Supports Untied Overclocking Technology (see CAUTION 3)

 

- Supports EM64T CPU

Chipset

- Northbridge: Intel® 865PE / 865G

 

- Southbridge: Intel® ICH5

Memory

- Dual Channel DDR Memory Technology (see CAUTION 4)

 

- 4 x DDR DIMM slots

 

- Support DDR400/333/266 (see CAUTION 5)

 

- Max. capacity: 4GB

Hybrid Booster

- CPU Frequency Stepless Control (see CAUTION 6)

 

- ASRock U-COP (see CAUTION 7)

 

- Boot Failure Guard (B.F.G.)

Expansion Slot

- 5 x PCI slots

 

- 1 x AGP slot (see CAUTION 8)

Audio

- Realtek ALC850 7.1 channel audio CODEC

 

 

LAN

- Realtek PCI LAN 8101L

 

- Speed: 10/100 Ethernet

 

- Supports Wake-On-LAN

Rear Panel I/O

ASRock 8CH I/O

 

- 1 x PS/2 Mouse Port

 

- 1 x PS/2 Keyboard Port

 

- 1 x Serial Port: COM1

 

- 1 x Parallel Port (ECP/EPP Support)

 

- 4 x Ready-to-Use USB 2.0 Ports

 

- 1 x RJ-45 LAN Port

 

- Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

 

Line in/Front Speaker/Microphone (see CAUTION 9)

6

 

Connector

- 2 x Serial ATA 1.5Gb/s connectors

 

 

 

(No Support for RAID and “Hot Plug” functions)

 

 

 

- 2 x ATA100 IDE connectors (support 4 x IDE devices)

 

 

 

- 1 x Floppy connector

 

 

 

- 1 x IR header

 

 

 

- 1 x Game header

 

 

 

- CPU/Chassis FAN connector

 

 

 

- 20 pin ATX power connector

 

 

 

- 4 pin 12V power connector

 

 

 

- CD in header

 

 

 

- Front panel audio connector

 

 

 

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

 

 

 

(see CAUTION 10)

 

 

BIOS Feature

- 4Mb AMI BIOS

 

 

 

- AMI Legal BIOS

 

 

 

- Supports “Plug and Play”

 

 

 

- ACPI 1.1 Compliance Wake Up Events

 

 

 

- Supports jumperfree

 

 

 

- AMBIOS 2.3.1 Support

 

 

Support CD

- Drivers, Utilities, AntiVirus Software (Trial Version)

 

 

Hardware

- CPU Temperature Sensing

 

 

Monitor

- Chassis Temperature Sensing

 

 

 

- CPU Fan Tachometer

 

 

 

- Chassis Fan Tachometer

 

 

 

- CPU Quiet Fan

 

 

 

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

 

OS

- Microsoft® Windows® 98SE / ME / 2000 / XP / XP 64-bit

 

 

 

compliant

 

 

Certifications

- FCC, CE, WHQL

 

 

 

 

 

7

CAUTION!

1.FSB1066 is only supported by overclocking mode. To support FSB1066 CPU, please use DDR400 DIMMs (Double Data Rate 400 MHz). Before installing FSB1066 CPU, please make sure that you have adjusted the jumpers correctly. The default setting of FSB1 is to short pin1 and pin2. However, if you want this motherboard to support FSB1066 CPU, please adjust your FSB1 jumper setting, and short pin2 and pin3 (see page 18).

2.About the setting of “Hyper Threading Technology”, please check page 26.

3.This motherboard supports Untied Overclocking Technology. Please read “Untied Overclocking Technology” on page 22 for details.

4.This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 15 for proper installation.

5.Please check the table below for the memory support frequency and its

corresponding CPU FSB frequency.

CPU FSB Frequency

Memory Support Frequency

800

DDR266, DDR333*, DDR400

533

DDR266, DDR333

1066

DDR400*

*When you use a FSB800-CPU on this motherboard, it will run at DDR320 if you adopt a DDR333 memory module. Besides, if you use a FSB1066-CPU on this motherboard, please adopt a DDR400 CL2.5 memory module.

6.Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.

7.While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system.

8.Do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage!

9.For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Please check the table on page 10 for proper connection.

10.Power Management for USB 2.0 works fine under Microsoft® Windows® XP 64-bit / XP SP1 or SP2 / 2000 SP4. It may not work properly under Microsoft® Windows® 98 / ME.

8

ASRock 865PE User Manual

1.3 Motherboard Layout

 

 

 

 

 

1

2

 

 

3

 

4

 

 

 

5 6

 

 

 

 

 

 

 

 

 

 

 

 

22.9cm (9.0 in)

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PS2

 

 

PS2_USB_PWR1

 

 

 

 

 

 

 

 

 

 

 

 

 

Mouse

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Keyboard

PS2

PARALLEL

 

 

ATX12V1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COM1

PORT

 

 

 

 

 

 

 

 

Presler

Conroe

module)

module)

module)

module)

 

7

USB 2.0

 

 

 

 

 

 

 

 

 

 

pin

pin

pin

pin

 

T: USB2

 

 

 

 

 

 

 

 

 

 

 

 

B: USB3

 

 

 

 

 

 

 

 

 

 

-

-

-

-

 

 

 

 

 

 

 

 

 

 

 

 

bit,184

184bit,

bit,184

184bit,

IDE2

 

USB 2.0

Top:

 

 

 

 

 

 

 

 

 

T: USB0

 

 

 

 

 

 

 

 

DDR1(64/72

(64/72DDR2

DDR3(64/72

(64/72DDR4

 

30.5cm(12.0in)

RJ-45

 

 

 

 

 

 

 

DualChannelDDR400

 

B: USB1

 

 

 

 

 

 

 

 

 

 

CTRBASS

Bottom:

SIDESPK

Center:

REARSPK

Top:

FAN1

 

 

 

 

 

 

 

29

 

 

 

 

 

 

ATXPWR1

Intel

 

 

Dual Core CPU

 

 

Bottom:

 

 

 

 

CPU

 

865PE/865G

FSB1066

 

 

 

 

 

 

 

 

 

28

 

 

 

 

 

 

Chipset

 

 

 

 

 

 

 

 

 

 

MICIN

FRONT

Center:

LINEIN

Top:

Super

IO

AGP 8X

 

IDE1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

27

 

 

 

 

 

 

 

 

1.5V_AGP1

 

 

 

 

 

 

 

 

 

 

 

 

4Mb

 

 

 

 

 

 

 

 

 

 

 

 

 

9

26

 

BIOS

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

FSB1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCI 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.1CH

 

 

 

 

 

 

Intel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCI 2

 

 

 

 

 

 

ICH5

 

 

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ConRoe865PE

 

 

 

`

 

 

 

 

 

 

 

 

 

 

PCI

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

LAN

 

 

 

PCI 3

RoHS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SATA

 

25

 

 

 

 

 

 

 

 

 

 

 

 

CMOS

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

Battery

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCI 4

 

 

 

 

 

CLRCMOS0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SATA1 SATA2

 

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

FAN1

 

 

 

 

CODEC

 

 

 

 

 

 

 

 

 

USB2.0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

_

 

 

 

 

 

 

 

 

 

 

 

1

 

 

1

 

 

 

CHA

 

 

 

 

 

 

 

 

 

PCI 5

 

USB45

 

USB67

 

 

 

 

 

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JR1

JL1

 

 

 

 

 

 

 

 

 

 

 

PANEL 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PLED PWRBTN

 

 

 

 

1

 

 

 

CD1

 

 

 

 

 

1

 

1

 

 

 

 

 

 

 

 

 

AUDIO1

 

 

GAME1

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

FLOPPY1

 

 

IR1

SPEAKER1

 

HDLED RESET

 

 

 

 

 

23

22

 

21

20

19 1817 16

 

15

 

 

1

PS2_USB_PWR1 Jumper

15

System Panel Header (PANEL1)

2

ATX 12V Connector (ATX12V1)

16

Chassis Speaker Header (SPEAKER 1)

3

775-Pin CPU Socket

17

USB 2.0 Header (USB67, Blue)

4

North Bridge Controller

18

Infrared Module Header (IR1)

5

2 x 184-pin DDR DIMM Slots

19

USB 2.0 Header (USB45, Blue)

 

(Dual Channel A: DDR1, DDR3; Blue)

20

Floppy Connector (FLOPPY1)

6

2 x 184-pin DDR DIMM Slots

21

Game Connector (GAME1)

 

(Dual Channel B: DDR2, DDR4; Black)

22

Internal Audio Connector: CD1 (Black)

7

Secondary IDE Connector (IDE2, Black)

23

Front Panel Audio Header (AUDIO1)

8

Primary IDE Connector (IDE1, Blue)

24

JR1 / JL1 Jumpers

9

FSB Select Jumper (FSB1)

25

PCI Slots (PCI1- 5)

10

South Bridge Controller

26

BIOS FWH Chip

11

Primary Serial ATA Connector (SATA1)

27

AGP Slot (1.5V_AGP1)

12

Secondary Serial ATA Connector (SATA2)

28

ATX Power Connector (ATXPWR1)

13

Clear CMOS Jumper (CLRCMOS0)

29

CPU Fan Connector (CPU_FAN1)

14

Chassis Fan Connector (CHA_FAN1)

 

 

9

1.4ASRock 8CH I/O

1

2

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

7

 

 

 

 

 

 

 

 

 

 

5

 

8

 

 

 

 

 

 

13

12

11

10

9

1

Parallel Port

 

8

Microphone (Pink)

2

RJ-45 Port

 

9

USB 2.0

Ports (USB01)

3

Side Speaker (Gray)

 

10

USB 2.0

Ports (USB23)

4

Rear Speaker (Black)

 

11

Serial Port: COM1

5

Central / Bass (Orange)

 

12 PS/2 Keyboard Port (Purple)

6

Line In (Light Blue)

 

13

PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

*If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels

Front Speaker

Rear Speaker

Central / Bass

Side Speaker

 

(No. 7)

(No. 4)

(No. 5)

(No. 3)

2

V

--

--

--

4

V

V

--

--

6

V

V

V

--

8

V

V

V

V

1 0

Chapter 2 Installation

ConRoe865PE is an ATX form factor (12.0" x 9.0", 30.5 x 22.9 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.

Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

1.Unplug the power cord from the wall socket before touching any component.

2.To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3.Hold components by the edges and do not touch the ICs.

4.Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.

Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply.

Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

1 1

2.3 CPU Installation

For the installation of Intel 775-LAND CPU, please follow the steps below.

775-Pin Socket Overview

Before you insert the 775-LAND CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing down and out on the hook to clear retention tab.

Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated Heat Sink) up. Locate Pin1 and the two orientation key notches.

lineblack

lineblack

Pin1

 

 

 

 

 

Pin1

 

 

 

 

alignment key

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

alignment key

 

 

 

 

 

orientation

orientation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

key notch

key notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

775-Pin Socket

 

 

 

 

775-LAND CPU

 

 

 

 

 

 

 

1 2

Loading...
+ 27 hidden pages