ASRock 4Core1600-D800 motherboard User Manual

Size:
1.06 Mb
Download

DRAM Voltage

Use this to select DRAM Voltage. Configuration options: [Auto], [1.72V], [1.81V], [1.86V], [1.90V], [1.95V], [1.99V], [2.04V] and [2.13V]. The default value of this feature is [Auto].

NB Core Voltage

Use this to select Northbridge Core Voltage. Configuration options: [Auto], [Low] and [High]. The default value of this feature is [Auto].

VTT Voltage

Use this to select VTT Voltage. Configuration options: [Auto], [Low] and [High]. The default value of this feature is [Auto].

+1.05V Voltage

Use this to select +1.05V Voltage. Configuration options: [Auto], [Low] and

[High]. The default value of this feature is [Auto].

+1.50V Voltage

Use this to select +1.50V Voltage. Configuration options: [Auto], [Low] and [High]. The default value of this feature is [Auto].

DRAM RCOMP Setting

Use this to adjust DRAM RCOMP Setting feature. Configuration options: [Auto] and [Manual]. The default value of this feature is [Auto].

31

3.3.3ACPI Configuration

BIOS SETUP UTILITY

Advanced

ACPI Configuration

Suspend To RAM

[Auto]

Repost Video on STR Resume

[No]

Restore on AC/Power Loss

[Power Off]

Ring-InPower On

[Disabled]

PCI Devices Power On

[Disabled]

PS / 2 Keyboard Power On

[Disabled]

RTC Alarm Power On

[Disabled]

ACPI HPET Table

[Disabled]

Select auto-detector disable the STR feature.

 

Select Screen

 

Select Item

+-

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2005,American Megatrends, Inc.

Suspend to RAM

Use this item to select whether to auto-detector disable theSuspend-to-RAM feature. Select [Auto] will enable this feature if the OS supports it. If you set this item to [Disabled], the function “Repost Video on STR Resume” will be hidden.

Repost Video on STR Resume

This feature allows you to repost video on STR resume. (STR refers to suspend to RAM.)

Restore on AC/Power Loss

This allows you to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers.

Ring-InPower On

Use this item to enable or disable Ring-Insignals to turn on the system from thepower-soft-offmode.

PCI Devices Power On

Use this item to enable or disable PCI devices to turn on the system from the power-soft-offmode.

PS/2 Keyboard Power On

Use this item to enable or disable PS/2 keyboard to turn on the system from the power-soft-offmode.

RTC Alarm Power On

Use this item to enable or disable RTC (Real Time Clock) to power on the system.

32

ACPI HPET Table

Use this item to enable or disable ACPI HPET Table. The default value is [Disabled]. Please set this option to [Enabled] if you plan to use this motherboard to submit Windows® VistaTM certification.

3.3.4IDE Configuration

BIOS SETUP UTILITY

Advanced

IDE Configuration

ATA/IDE Configuration

[Enhanced]

SATAII 1

[Hard Disk]

SATAII 2

[Not Detected]

SATAII 3

[Not Detected]

SATAII 4

[Not Detected]

IDE1 Master

[Not Detected]

IDE2 Slave

[Not Detected]

Set [Compatible] when Legacy OS (MS-DOS,Win NT) is used.

Set [Enhanced] when Native OS (Win 2000/XP) is used.

 

Select Screen

 

Select Item

+-

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2003,American Megatrends, Inc.

ATA/IDE Configuration

Please select [Compatible] when you install legacy OS (Windows® NT). If native OS (Windows® 2000 / XP) is installed, please select [Enhanced].

When [Compatible] is selected

Combined Option

It allows you to select between [SATA 1, SATA 2, SATA 3, SATA 4], [SATA 1, SATA 3, IDE 1], and [IDE 1, SATA 2, SATA 4]. If it is set to [SATA 1, SATA 3, IDE 1], then SATAII_2 and SATAII_4 will not work. Likewise, if it is set to [IDE 1, SATA 2, SATA 4], then SATAII_1 and SATAII_3 will not work.

Because Intel® ICH7 south bridge only supports four IDE devices under legacy OS (Windows® NT), you have to choose [SATA 1, SATA 2, SATA 3, SATA 4], [SATA 1, SATA 3, IDE 1], or [IDE 1, SATA 2, SATA 4] when the installed device is used with legacy OS.

 

[SATA 1, SATA 2,

[SATA 1, SATA 3,

[IDE 1, SATA 2,

 

SATA 3, SATA 4]

IDE 1]

SATA 4]

Master

SATAII_1,

SATAII_1

SATAII_2

SATAII_2

 

 

 

 

 

 

 

Slave

SATAII_3,

SATAII_3

SATAII_4

SATAII_4

 

 

 

33

IDE Device Configuration

You may set the IDE configuration for the device that you specify. We will use the “Primary IDE Master” as the example in the following instruction.

BIOS SETUP UTILITY

Advanced

Primary IDE Master

Device

:Hard Disk

Vendor

:ST340014A

Size

:40.0 GB

LBA Mode

:Supported

Block Mode

:16Sectors

PIO Mode

:4

Async DMA

:MultiWord DMA-2

Ultra DMA

:Ultra DMA-5

S.M.A.R.T.

:Supported

 

 

Type

[Auto]

LBA/Large Mode

[Auto]

Block (Multi-SectorTransfer)

[Auto]

PIO Mode

[Auto]

DMA Mode

[Auto]

S . M . A . R . T .

[Disabled]

32Bit Data Transfer

[Enabled]

Select the type

of device connected to the system.

 

Select Screen

 

Select Item

+-

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2005,American Megatrends, Inc.

TYPE

Use this item to configure the type of the IDE device that you specify. Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].

[Not Installed]: Select [Not Installed] to disable the use of IDE device.[Auto]: Select [Auto] to automatically detect the hard disk drive.

After selecting the hard disk information into BIOS, use a disk utility, such as FDISK, to partition and format the new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active.

[CD/DVD]: This is used for IDE CD/DVD drives.

[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device), such as MO.

LBA/Large Mode

Use this item to select the LBA/Large mode for a hard disk > 512 MB under

DOS and Windows; for Netware and UNIX user, select [Disabled] to disable the LBA/Large mode.

Block (Multi-SectorTransfer)

The default value of this item is [Auto]. If this feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer.

PIO Mode

Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing.

34

DMA Mode

DMA capability allows the improved transfer-speedanddata-integrityfor compatible IDE devices.

S.M.A.R.T.

Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring,Analysis, and Reporting Technology) feature. Configuration options: [Disabled], [Auto], [Enabled].

32-BitData Transfer

Use this item to enable 32-bitaccess to maximize the IDE hard disk data transfer rate.

3.3.5PCIPnP Configuration

BIOS SETUP UTILITY

Advanced

Advanced PCI / PnP Settings

PCI

Latency Timer

[32]

PCI

IDE BusMaster

[Enabled]

Value in units of PCI clocks for PCI device latency timer register.

 

Select Screen

 

Select Item

+-

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2005,American Megatrends, Inc.

PCI Latency Timer

The default value is 32. It is recommended to keep the default value unless the installed PCI expansion cards’ specifications require other settings.

PCI IDE BusMaster

Use this item to enable or disable the PCI IDE BusMaster feature.

35

3.3.6 Floppy Configuration

In this section, you may configure the type of your floppy drive.

 

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Floppy Configuration

 

Select the type of

 

 

floppy drive

Floppy A

[1.44 MB 312"]

connected to the

 

 

system.

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005,American Megatrends, Inc.

3.3.7 Super IO Configuration

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Configure Super IO Chipset

 

Allow BIOS to Enable

 

 

or Disable Floppy

OnBoard Floppy Controller

[Enabled]

Controller.

 

 

Serial Port Address

[3F8 / IRQ4]

 

 

Infrared Port Address

[Disabled]

 

 

Parallel Port Address

[378]

 

 

Parallel Port Mode

[ECP + EPP]

 

 

EPP Version

[1.9]

 

 

ECP Mode DMA Channel

[DMA3]

 

 

Parallel Port IRQ

[IRQ7]

 

 

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005,American Megatrends, Inc.

OnBoard Floppy Controller

Use this item to enable or disable floppy drive controller.

Serial Port Address

Use this item to set the address for the onboard serial port or disable it. Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4], [2E8 / IRQ3].

Infrared Port Address

Use this item to set the address for the onboard infrared port or disable it. Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3]. If you plan to use ASRock DeskExpress on this motherboard, please keep this item on [Disabled] option.

36

Parallel Port Address

Use this item to set the address for the onboard parallel port or disable it. Configuration options: [Disabled], [378], and [278].

Parallel Port Mode

Use this item to set the operation mode of the parallel port. The default value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP version in the following item, “EPP Version”. Configuration options: [Normal], [Bi-Directional],and [ECP+EPP].

EPP Version

Use this item to set the EPP version. Configuration options: [1.9] and [1.7].

ECP Mode DMA Channel

Use this item to set the ECP mode DMA channel. Configuration options: [DMA0], [DMA1], and [DMA3].

Parallel Port IRQ

Use this item to set the IRQ for the parallel port. Configuration options: [IRQ5] and [IRQ7].

37

3.3.8USB Configuration

 

 

 

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

USB Configuration

 

To enable or disable

 

 

the onboard USB

USB Controller

[Enabled]

controllers.

 

 

USB 2.0 Support

[Enabled]

 

 

Legacy USB Support

[BIOS Setup Only]

 

 

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005,American Megatrends, Inc.

USB Controller

Use this item to enable or disable the use of USB controller.

USB 2.0 Support

Use this item to enable or disable the USB 2.0 support.

Legacy USB Support

Use this option to select legacy support for USB devices. There are four configuration options: [Enabled], [Auto], [Disabled] and [BIOS Setup Only]. The default value is [BIOS Setup Only]. Please refer to below descriptions for the details of these four options:

[Enabled] - Enables support for legacy USB.

[Auto] - Enables legacy support if USB devices are connected.

[Disabled] - USB devices are not allowed to use under legacy OS and BIOS setup when [Disabled] is selected. If you have USB compatibility issue, it is recommended to select [Disabled] to enter OS.

[BIOS Setup Only] - USB devices are allowed to use only under BIOS setup and Windows / Linux OS.

38

3.4 Hardware Health Event Monitoring Screen

In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.

 

 

BIOS SETUP UTILITY

 

 

Main

Advanced

H/W Monitor

Boot

Security

Exit

Hardware Health Event Monitoring

Enable/Disable

 

CPU Quiet Fan

 

 

 

 

 

 

 

 

Function.

 

CPU Temperature

: 37 C / 98 F

 

 

 

M / B Temperature

: 31 C / 87 F

 

 

 

CPU Fan Speed

: 3400 RPM

 

 

 

Chassis Fan Speed

: N / A

 

 

 

Vcore

 

: 1.629V

 

 

 

+ 3.30V

 

: 3.306V

 

 

 

+ 5.00V

 

: 5.067V

 

Select Screen

 

+ 12.00V

: 11.890V

 

 

 

Select Item

 

 

 

 

 

 

 

 

 

F1

General Help

 

CPU Quiet Fan

[Disabled]

F9

Load Defaults

 

 

 

 

F10

Save and Exit

 

 

 

 

ESC

Exit

 

 

v02.54 (C) Copyright 1985-2003,American Megatrends, Inc.

 

CPU Quiet Fan

This item allows you to identify the temperature of CPU fan. If you set this option as [Disabled], the CPU fan will operate in full speed. If you set this option as [Enabled], you will find the items “Target CPU Temperature” and “Target Fan Speed” appear to allow you adjusting them. The default value is [Disabled]. You are allowed to enable this function only when you install 4-pinCPU fan.

Target CPU Temperature

The target temperature will be between 45C/113 F and 65C/149F. The default value is [50C/122F].

Target Fan Speed

Use this option to set the target fan speed. You can freely adjust the target fan speed according to the target CPU temperature that you choose. Configuration options: [Level 1], [Level 2], [Level 3], [Level 4], [Level 5], [Level 6] [Level 7], [Level 8] and [Level 9].

39

3.5 Boot Screen

In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority.

BIOS SETUP UTILITY

Main

Advanced

H/W Monitor

Boot

Security

Exit

Boot Settings

Boot Settings Configuration

1st Boot Device

[1st Floppy Device]

2nd Boot Device

[HDD: PM - HDS722580VL]

3rd Boot Device

[CD / DVD: 3S - CD - ROM C]

4th Boot Device

[USB]

Hard Disk Drives

 

Removable Drives

 

CD/DVD Drives

 

Configure Settings during System Boot.

 

Select Screen

 

Select Item

Enter

Go to Sub Screen

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2005,American Megatrends, Inc.

40