Apple CP-X250 User Manual

Size:
2.21 Mb
Download

Projector

CP-S240/CP-X250

CP-S245/CP-X255

User's Manual – Quick Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read the "User's Manual - Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference.

NOTE • The information in this manual is subject to change without notice.

The manufacturer assumes no responsibility for any errors that may appear in this manual.

The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

ENGLISH

Contents of package

(1)Projector

(2)Remote control

with two AA batteries

(3)Power cord

(4)RGB cable

(5)Audio/Video cable

(6)Soft case

(7)User’s manuals

(8)Lens cover, Rivet and Strap

(1)

(2)

(3)

(5)

 

 

 

 

(6)

(7)

(8)

NOTE • Keep the original moving the projector, be sure caution for the lens part.

packing materials for future reshipment. For to use the original packing materials. Use special

1

Arrangement

Arrangement

WARNING ►Install the projector in a suitable environment according to instructions of the "User's Manual - Safety Guide".

CAUTION ►This projector has some intake vents also on the bottom. Avoid blocking vents. Put nothing that is sucked or sticks to the bottom of projector.

(calculated for a full size screen, ±10%)

4:3

16:9

(a)

(a)

For the model CP-S240/CP-S245

(c) up

(c) down

(b)

(a) Screen size [inch (m)]

 

4 : 3 screen

 

 

 

 

16 : 9 screen

 

(b) Projection distance

(c) Screen height

 

(b) Projection distance [m

(c) Screen height

[m (inch)]

[cm (inch)]

 

 

 

(inch)]

[cm (inch)]

 

min.

max.

down

 

up

 

min.

 

max.

down

 

up

30

(0.8)

 

0.9

(36)

1.1

(43)

5

(2)

41

(16)

 

1.0

(39)

1.2

(47)

-1

(0)

39

(15)

40

(1.0)

 

1.2

(48)

1.5

(57)

6

(2)

55

(22)

 

1.3

(52)

1.6

(63)

-2

(-1)

51

(20)

50

(1.3)

 

1.5

(60)

1.8

(72)

8

(3)

69

(27)

 

1.7

(65)

2.0

(79)

-2

(-1)

64

(25)

60

(1.5)

 

1.8

(72)

2.2

(87)

9

(4)

82

(32)

 

2.0

(79)

2.4

(94)

-2

(-1)

77

(30)

70

(1.8)

 

2.1

(84)

2.6

(101)

11

(4)

96

(38)

 

2.3

(92)

2.8

(110)

-3

(-1)

90

(35)

80

(2.0)

 

2.4

(96)

2.9

(116)

12

(5)

110

(43)

 

2.7

(105)

3.2

(126)

-3

(-1)

103

(41)

90

(2.3)

 

2.8

(109)

3.3

(130)

14

(5)

123

(49)

 

3.0

(118)

3.6

(142)

-4

(-1)

116

(46)

100

(2.5)

 

3.1

(121)

3.7

(145)

15

(6)

137

(54)

 

3.3

(132)

4.0

(158)

-4

(-2)

129

(51)

120

(3.0)

 

3.7

(145)

4.4

(174)

18

(7)

165

(65)

 

4.0

(158)

4.8

(190)

-5

(-2)

154

(61)

150

(3.8)

 

4.6

(182)

5.5

(218)

23

(9)

206

(81)

 

5.0

(198)

6.0

(238)

-6

(-2)

193

(76)

200

(5.1)

 

6.2

(242)

7.4

(291)

30

(12)

274

(108)

 

6.7

(264)

8.1

(317)

-8

(-3)

257

(101)

250

(6.4)

 

7.7

(303)

9.3

(364)

38

(15)

343

(135)

 

8.4

(330)

10.1 (397)

-10

(-4)

322

(127)

300

(7.6)

 

9.2

(364)

11.1

(437)

46

(18)

411

(162)

 

10.1 (397)

12.1 (476)

-12

(-5)

386

(152)

For the model CP-X250/CP-X255

(a) Screen

 

 

 

 

4 : 3 screen

 

 

 

 

 

 

16 : 9 screen

 

 

 

(b) Projection distance

 

(c) Screen height

 

(b) Projection distance [m

(c) Screen height

size

 

 

[m (inch)]

 

 

 

[cm (inch)]

 

 

 

(inch)]

 

 

[cm (inch)]

 

[inch (m)]

 

 

 

 

 

 

 

 

 

 

 

 

min.

max.

down

up

 

min.

max.

down

up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

(0.8)

 

0.9

(36)

1.1

(43)

5

(2)

41

(16)

1.0

(39)

1.2

(47)

-1

(0)

39

(15)

40

(1.0)

 

1.2

(48)

1.5

(58)

6

(2)

55

(22)

 

1.3

(52)

1.6

(63)

-2

(-1)

51

(20)

50

(1.3)

 

1.5

(60)

1.8

 

(73)

8

(3)

69

(27)

 

1.7

(66)

2.0

(79)

-2

(-1)

64

(25)

60

(1.5)

 

1.8

(73)

2.2

 

(87)

9

(4)

82

(32)

 

2.0

(79)

2.4

(95)

-2

(-1)

77

(30)

70

(1.8)

 

2.2

(85)

2.6

 

(102)

11

(4)

96

(38)

 

2.4

(93)

2.8

(111)

-3

(-1)

90

(35)

80

(2.0)

 

2.5

(97)

3.0

 

(117)

12

(5)

110

(43)

 

2.7

(106)

3.2

(127)

-3

(-1)

103

(41)

90

(2.3)

 

2.8

(109)

3.3

 

(132)

14

(5)

123

(49)

 

3.0

(119)

3.6

(143)

-4

(-1)

116

(46)

100

(2.5)

 

3.1

(122)

3.7

 

(146)

15

(6)

137

(54)

 

3.4

(133)

4.0

(159)

-4

(-2)

129

(51)

120

(3.0)

 

3.7

(146)

4.5

 

(176)

18

(7)

165

(65)

 

4.0

(159)

4.9

(192)

-5

(-2)

154

(61)

150

(3.8)

 

4.6

(183)

5.6

 

(220)

23

(9)

206

(81)

 

5.1

(200)

6.1

(240)

-6

(-2)

193

(76)

200

(5.1)

 

6.2

(244)

7.5

 

(294)

30

(12)

274

(108)

 

6.8

(266)

8.1

(320)

-8

(-3)

257

(101)

250

(6.4)

 

7.8

(306)

9.3

 

(367)

38

(15)

343

(135)

 

8.5

(333)

10.2 (400)

-10

(-4)

322

(127)

300

(7.6)

 

9.3

(367)

11.2

(441)

46

(18)

411

(162)

 

10.2 (400)

12.2 (480)

-12

(-5)

386

(152)

2

Adjusting the projector's elevator

Adjusting the projector's elevator

CAUTION ►If you press the elevator button without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet. ►Do not incline the projector rightward or leftward. Also do not incline it backward or forward exceeding 9 degrees. Exceeding these range could cause malfunction, and could shorten the lifetime of the consumables.

►Except for inclining by the elevator feet adjustment, place the projector horizontally.

1. After making sure that the projector is cool adequately, press and hold in the elevator buttons while holding the projector. The elevator buttons and the elevator feet are on the both sides.

2. Raise or lower the projector to the desired height and release the elevator buttons.

When you release the elevator buttons, the elevator feet will lock into position.

Elevator feet

Elevator

 

button

3. If necessary, you can also finely adjust the height of the projector by twisting the elevator feet by hand.

ENGLISH

3

Connecting your devices

Connecting your devices

Examples of connection with a computer

* In the default setting, the AUDIO IN1 port is the audio port for the RGB IN1 and RGB IN2 ports. To change the settings, refer to the AUDIO item in the SETUP menu.

 

RGB cable

 

USB cable

 

 

 

 

 

 

 

 

 

 

 

Y

AUDIO IN2

 

 

 

 

 

R

 

 

 

 

 

 

CONTROL

RGB IN1

 

 

 

 

CB/PB

 

RGB IN2

USB

 

 

 

L

RGB OUT

 

RGB out

Audio out

RS-232CUSB

CR/PR

 

K

 

 

 

 

 

 

 

 

 

 

VIDEO

 

 

 

 

 

S-VIDEO

 

 

Stereo mini

RS-232Ccable

Use the RGB IN OUT

 

 

 

 

 

audio cable

 

 

 

switch to select RGB IN2

 

 

 

 

 

(RGB IN2 is selected if

 

 

Stereo mini audio cable

the switch is not pushed

 

 

 

 

 

in).

 

RGB out

Audio out

Y R

 

 

AUDIO IN

 

 

CONTROL

RGB IN1

CB/PB

 

AUDIO OUT

USB

L

 

 

AUDIO IN1

K

CR/PR

 

 

 

 

VIDEO

 

 

 

RGB cable

S-VIDEO

For the models CP-S245/CP-X255

RGB out

LAN

LAN cable

Y

AUDIO IN2

 

 

 

 

R

 

 

 

 

 

 

 

CONTROL

RGB IN1

 

CB/PB

 

AUDIO OUT

RGB IN2

USB

L

RGB OUT

 

 

AUDIO IN1

 

K

CR/PR

 

 

 

 

 

 

 

VIDEO

 

LINK

LAN

 

 

S-VIDEO

ACT

 

 

 

 

 

 

RGB cable

*Only the CP-S245/CP-X255have a LAN port.

4

Connecting to a monitor (output)

RGB in

RGB cable

Connecting your devices

Use the RGB IN OUT switch to select RGB OUT (RGB OUT is selected if the switch is pushed in).

Y

AUDIO IN2

 

 

 

R

 

 

 

 

 

CONTROL

RGB IN1

RGB OUT

CB/PB

 

AUDIO OUT

 

USB

L

 

 

 

AUDIO IN1

 

K

CR/PR

 

 

 

 

 

 

VIDEO

 

 

 

 

S-VIDEO

 

 

 

ENGLISH

Connecting to a speaker with amplifier (output)

Audio in

AUDIO IN2

Y R

 

 

 

CONTROL

RGB IN1

 

CB/PB

 

AUDIO OUT

RGB IN2

USB

L

RGB OUT

 

 

AUDIO IN1

K

 

CR/PR

 

Stereo mini audio cable

VIDEO

 

S-VIDEO

 

 

 

Examples of connection with a VCR/DVD player

* In the default setting, the AUDIO IN2 L/R port is the audio port for the VIDEO, S-VIDEOand COMPONENT VIDEO ports. To change the settings, refer to the AUDIO item in the SETUP menu.

Audio/Video cable

Audio (R) out

Audio (L) out

Video out

Audio cable

Y

AUDIO IN2

 

 

R

 

 

 

CONTROL

RGB IN1

 

CB/PB

AUDIO OUT

RGB IN2

USB

RGB OUT

 

CR/PR

AUDIO IN1

 

K

 

 

 

VIDEO

 

 

 

S-VIDEO

 

 

Audio (R) out

Audio (L) out

Y

AUDIO IN2

 

 

R

 

 

 

CONTROL

RGB IN1

 

CB/PB

AUDIO OUT

RGB IN2

USB

RGB OUT

 

CR/PR

AUDIO IN1

 

K

 

 

 

S-VideooutS-Videocable

VIDEO S

Component video out

Component video cable

 

 

Y

 

 

2

 

 

 

Y

R

 

 

CB/PB

 

 

 

 

 

CONTROL

RGB IN1

 

 

CB/PB

 

AUDIO OUT

RGB IN2

USB

 

L

RGB OUT

 

CR/PR

 

AUDIO IN1

 

K

CR/PR

 

 

 

 

 

 

 

VIDEO

 

 

 

 

Audio (R) out

S-VIDEO

 

 

 

 

 

 

 

 

Audio (L) out

Audio cable

5

 

 

Putting batteries into the remote control / Connecting the power supply

Putting batteries intothe remote control

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets.

Do not recharge, short circuit, solder or disassemble a battery.

Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the liquid adheres to your body or clothes, rinse well with water immediately.

1. Remove the battery cover.

Slide back and remove the battery cover in the direction of the arrow.

2. Insert the batteries.

Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control.

3. Close the battery cover.

Replace the battery cover in the direction of the arrow and snap it back into place.

Connecting the power supply

WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock.

Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.

Only plug the power cord into an outlet rated for use with the power cord's specified voltage range.

Never modify the power cord. Never attempt to defeat the ground connection of the three-prongedplug.

Connect the connector of the power cord

AC inlet

1. to the AC inlet of the projector.

 

2. Firmly plug the power cord's plug into

the outlet. Connector

of the power cord

6

Operating

 

Operating

 

 

WARNING ►When the power is on, a strong light is emitted. Do not look into

the lens of projector. Also do not peep at the inside of projector through a hole.

Turning on the power

POWER

 

1.

 

 

Set the power switch to the ON position.

(Steady orange)

 

 

 

2.

Press the STANDBY/ON (projector or

POWER

POWER

 

 

 

 

remote control) button.

(Blinking in green) (Steady green)

Displaying

 

1.

To select an input signal, use the button of INPUT (projector),

 

2.

of RGB, VIDEO or SEARCH (remote control).

 

To change the aspect ratio, use the button

Focus ring

 

3.

ASPECT (remote control).

 

To adjust the zoom and focus, use the

 

 

 

 

zoom knob and the focus ring.

 

or the buttons

Zoom knob

Turning off the power

This product is able to turn off the main power during the cooling. However, please pay special attention to below two points when you do:

(1)Please do not turn the projector on again for at least 1 minute in this case. Neglect could shorten the lifetime of the lamp.

(2)During use or immediately after use, do not touch around the lamp and vents of the projector. It could cause a burn.

1.

Press the STANDBY/ON (projector or remote control) button.

 

2.

The message "Power off?" will appear on the screen for approximately 5 seconds.

Press the STANDBY/ON (projector or remote control) button again while the

 

 

message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3.

Make sure that the power indicator lights in steady

 

 

orange, and set the power switch to the OFF position.

POWER

(Blinking in orange)

POWER

(Steady orange)

The POWER indicator will go off.

ENGLISH

7

Control buttons / Remote control

Controlbuttons

Cursor buttons ▲,▼,◄,►

STANDBY/ON button

Remote control

LAMP indicator TEMP indicatorPOWER indicator

INPUT button

SEARCH button

RGB button

VIDEO RGB SEARCH

VIDEO button

ASPECT button

ASPECT

 

AUTO

BLANK

 

 

 

 

HOME button

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

MAGNIFY

OFF

END

PAGE DOWN

MUTE

ON button

 

 

 

 

OFF button

FREEZE

 

 

KEYSTONE

 

 

 

END button

 

 

 

 

FREEZE button

POSITION

 

 

MENU

POSITION button

 

ENTER

 

ESC button

ESC

 

 

RESET

 

 

 

Battery cover (on the back)

STANDBY/ON button AUTO button BLANK button PAGE UP button VOLUME button MUTE button PAGE DOWN button KEYSTONE button

MENU button

Cursor buttons ▲,▼,◄,►

ENTER button RESET button

8

Lamp

Lamp

WARNING

HIGH VOLTAGE

 

HIGH TEMPERATURE HIGH PRESSURE

 

►The projector uses a high-pressuremercury glass lamp. The lamp canbreak

with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible forshards of glass to fly into the lamp housing, and forgas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not

put it in a trash. Dispose of it in accordance with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in the US)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

 

• If the lamp should break (it will make a loud bang when it does), unplug

 

the power cord from the outlet, and make sure to request a replacement

 

lamp from your local dealer. Note that shards of glass could damage the

 

inside of the projector, or cause injury during handling, so please do not

 

try to clean the projector or replace the lamp yourself.

 

• If the lamp should break (it will make a loud bang when it does),

Disconnect

ventilate the room well, and make sure not to breathe the gas that

the plug

comes out of the projector vents, or get it in your eyes or mouth.

from the

• Before replacing the lamp, turn the projector off and unplug the power

power

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

outlet

Handling the lamp while hot can cause burns, as well as damaging the

 

lamp.

 

• Never unscrew except the appointed (marked by an arrow) screws.

 

• Do not open the lamp cover while the projector is suspended from

 

the ceiling. This is dangerous, since if the lamp’s bulb has broken, the

 

shards will fall out when the cover is opened. In addition, working in

 

high places is dangerous, so ask your local dealer to have the lamp

 

replaced even if the bulb is not broken.

 

• Do not use the projector with the lamp cover removed. To replace the

 

lamp, make sure that the screws are tightened firmly. Loose screws

 

could result in damage or injury.

 

• Use only the lamp of the specified type.

 

• If the lamp breaks soon after the first time it is used, it is possible

 

that there are electrical problems elsewhere besides the lamp. If this

 

happens, contact your local dealer or a service representative.

 

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

 

• Using the lamp for long periods of time, could cause it dark, not to light

 

up or to burst. When the pictures appear dark, or when the color tone

 

is poor, please replace the lamp as soon as possible. Do not use old

 

(used) lamps; this is a cause of breakage.

ENGLISH

9

6.
7.
1.
2.

Lamp (continued)

A lamp has a finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.

To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number = DT00731.

Turn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes.

Prepare a new lamp.

If the projector is mounted on the ceiling, or if the lamp the dealer to replace the lamp.

In the case of replacement by yourself,

3. Loosen the lamp cover screw (marked by arrow) and then slide the lamp cover to the side to remove it.

4. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles.

5. Insert the new lamp, and retighten firmly the two screws that are loosened in the previous process to lock it in place.

Slide the lamp cover back in place and firmly fasten the lamp cover screws.

Turn the projector on and reset the lamp time using the LAMP TIME function in the OPTION menu.

(1)Press the MENU button to display a menu. Only when the EASY MENU has appeared, please perform the next step (2).

(2)Point at the “Go To Advance Menu …” in the menu using ▼/▲ button, then press the ► button.

(3)Point at the “OPTION” in the left column of the menu using ▼/▲ button, then press the ► button.

(4)Point at the ”LAMP TIME” using ▼/▲ button, then press the ► button. A dialog will appear.

(5)Press the ▲ button to select “RESET” on the dialog. It performs resetting the lamp time.

has broken, also ask

Lamp cover

Screw

Screws

Handle

NOTE • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

10