Antec ISK 300-65 User Manual

Size:
738.04 Kb
Download

ISK 300-65

USERSMANUAL

TABLE OFCONTENTS

INTRODUCTION

1.1Case Specifications.…..…………………………………………………………………………………..3

1.2Diagram…………………………………………………………………….…………………………………. 3

1.3Power Supply Specifications…………………………………………………………………………. 4

HARDWAREINSTALLATIONGUIDE

2.1Removing the Top Panel.……………………………………………………………………………….5

2.2Removing the Drive Tray Assembly……….……………………………………………………… 5

2.3Motherboard Installation..…………………………………………………………………………….5

2.4Internal 2.5” Device Installation…………………………………………………………………….5

2.5External Slim 5.25” Device Installation…………………………………………………………. 6

CONNECTING THEFRONTI/O PORTS

3.1USB 2.0 Ports………………………………………………….……………………………………………. 7

3.2eSATA Port…………………………………….………………………………………………………………7

3.3AC’97 / HD Audio Ports……………………….…………………………………………………………7

3.4Switch and LED Connectors……………………………………………………………………………8

3.5Rewiring Motherboard Header Connections………………………………………………… 8

COOLINGSYSTEM

4.1TriCool™ Exhaust Fan…………………………………………………………………………………….9

1

ISK 300-65USERS MANUAL

At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct.

Disclaimer

This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive instructions on installing the motherboard and peripherals, please refer to the user’s manuals that come with those components.

Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend taking the appropriate time and care when working with it. Avoid hurried or careless motions. Please use reasonable precaution.

This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the motherboard manual for specific mounting instructions and troubleshooting. Before proceeding, check the manual for your CPU cooler to find out if there are steps you must take before installing the motherboard. While installing hardware, keep your case on a flat, stable surface.

2

1.1CASESPECIFICATIONS

Case Type

Mini-ITXDesktop

Color

Black

 

 

Dimensions

96mm (H) X 222mm (W) X 328mm (D)

 

3.8” (H) x 8.7” (W) x 12.9” (D)

Net Weight

5.5 lbs / 2.5 kg

 

 

Cooling

1 x Side 80mm TriCool™ fan

 

 

Drive Bays

3 Drive Bays:

 

- 1 x External 5.25” slim drive bay

 

- 2 x Internal 2.5” drive bays

Expansion Slots

1 x Half-heightslot

 

 

Motherboard Size

Mini-ITX

 

 

Front I/O Panel

2 x USB 2.0

 

1 x eSATA

 

AC’97 / HD Audio In and Out

 

 

Power Adapter

EP-65power adapter and PCB

 

 

1.2DIAGRAM

1.Side 80mm TriCool™ fan

2.External slim optical 5.25” drive bay

3.Internal 2 x 2.5” HDD bays

4.Half-heightexpansion slot

5.Motherboard mount – Mini-ITX

6.Front I/O panel

7.EP-65power adapter (not pictured)

3

1.3POWERSUPPLYSPECIFICATIONS

The ISK 300-65is powered by anEP-65power adapter.

Input characteristics:

Rated Voltage

 

Input Voltage Range

 

Frequency Range

 

 

 

 

 

 

 

100 VAC ~ 240 VAC

 

90 VAC ~ 264 VAC

 

50 Hz ~ 60 Hz

 

 

 

 

 

 

 

Output characteristics:

 

 

 

 

 

 

 

 

 

 

 

 

Rated

Rated

Voltage Range

Output

 

Ripple & Noise

Power

Voltage

Current

 

 

 

 

 

 

 

 

 

 

 

65W

19V

18.4V ~ 20.0V

0A ~ 3.42A

 

< 350mV

 

 

 

 

 

 

 

A variety of industrial-gradesafety circuitry will help protect your computer: OVP (Over Voltage Protection), SCP (Short Circuit Protection), OTP (Over Temperature Protection), and OCP (Over Current Protection). Sometimes the PSU will “latch” into a protected shutdown state. This means that you will need to power off the adapter and clear the fault before it will function again.

There are no user-replaceablefuses in theEP-65.

4

HARDWAREINSTALLATIONGUIDE

2.1 REMOVING THE TOP PANEL

Place the case flat on an even, stable surface.

1.Remove the three thumbscrews from the rear of the top panel.

2.Grip the top panel and slide it back several inches until it stops.

3.Grip the panel from the sides and lift it up until it pulls completely free of the main chassis.

Note: Do not use your fingernails to pry or lift the panels.

2.2 REMOVING THE DRIVE TRAY ASSEMBLY

Remove the top panel as detailed in section 2.1.

1.Using a Phillips-headscrewdriver, remove the three screws on the top of the tray that attach it to the chassis.

2.Grip the tray in the middle and pull it a few inches toward the rear of the case until it pulls loose.

3.Pull the drive tray assembly up and completely free of the chassis.

2.3 MOTHERBOARDINSTALLATION

Remove the top panel and remove the drive tray assembly as detailed in sections 2.1 and 2.2.

1.Lay the case down, with the open side facing up. The drive cages and power supply should be visible.

2.Make sure you have the correct I/O panel for your motherboard. If the panel provided with the case isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. Install the I/O panel at the rear of the case.

3.Align your motherboard with the motherboard standoff holes located at the rear of the case.

4.Screw in your motherboard to the standoffs with the provided Phillips-headscrews.

Your motherboard is now installed.

5

2.4 INTERNAL2.5” DEVICEINSTALLATION

Remove the top panel as described in section 2.1. Included at the top of the drive tray assembly is a HDD tray that can support up to two 2.5” devices.

1.On the right side of the drive tray assembly, remove the thumbscrew holding the HDD tray to the rest of the device.

2.Slide the HDD tray back a centimeter so the locking hinges unhook.

3.Pull the HDD tray away from the drive tray assembly.

4.Align your 2.5” device with the HDD tray. Invert the tray so the lower screw holes are accessible, then secure the device to the tray with the provided Phillips-headscrews.

5.Reattach the HDD tray to the drive tray assembly and replace the thumbscrew.

6.Connect the data and power connectors from the motherboard and power adapter to the device.

2.5 EXTERNALSLIM5.25” DEVICEINSTALLATION

Remove the top panel and drive tray assembly as described in sections 2.1 and 2.2. There is one externally accessible 5.25” drive bay that is compatible with a slim 5.25” optical drive.

1.While facing the front of the case, press on the upper right of the front of the 5.25” drive bay cover until it clicks, then release to allow the cover to unhinge.

2.Remove the drive bay face plate by applying pressure to the inside of the plate until it pops free of the bezel.

3.Install your slim optical drive in the drive bay assembly by sliding it into position from the rear of the assembly. Secure the device in place by attaching the included small screw on the right-handside of the tray.

4.Connect the data and power connectors from the motherboard and power adapter to the device.

5.Replace the drive tray assembly in the chassis.

6

CONNECTING THEFRONTI/O PORTS

3.1 USB 2.0

Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the motherboard manual to ensure that it matches the table below:

1

2

 

 

 

 

 

 

Pin

Signal Names

Pin

Signal Names

 

 

1

USB Power 1

2

USB Power 2

 

 

3

Negative Signal 1

4

Negative Signal 2

 

 

5

Positive Signal 1

6

Positive Signal 2

 

 

7

Ground 1

8

Ground 2

9

10

9

Key (No Connection)

10

Empty Pin

3.2 ESATA

You will find a SATA connector on a cable attached to the front ports. This internal SATA connector is designed to connect to a standard SATA connector on your motherboard. This will allow high-speedexternal hard disk enclosures such as the AntecMX-1to run at the same speeds as internally installed hard disks.

3.3 AC’97 / HD AUDIO PORTS

There is an Intel® standard 10-pinAC’97 connector and an Intel®10-pinHDA (High Definition Audio) connector linked to the front panel of the case.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin

Signal Names

Pin

Signal Names

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(HDA)

(AC’97)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

MIC2 L

1

MIC In

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

AGND

2

GND

10

 

6 4 2

 

 

 

 

 

 

3

MIC2 R

3

MIC Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

AVCC

4

NC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

FRO-R

5

Line Out (R)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9 7 5 3 1

 

 

 

 

 

 

6

MIC2_JD

6

Line Out (R)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

F_IO_SEN

7

NC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

Key (no pin)

8

Key (no pin)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

FRO-L

9

Line Out (L)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

LINE2_JD

10

Line Out (L)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You can connect either the AC’97 or the HDA connector, depending on your motherboard. Locate the internal audio connectors from your motherboard or sound card and connect the corresponding audio cable. Consult your motherboard or sound card manual for the pin-outpositions. Even if your system supports both standards, only use one connector.

7

3.4 POWERSWITCH/ RESETSWITCH/ HARDDISKDRIVELED CONNECTORS

Connected to your front panel are LED and switch leads for power, reset, and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard user’s manual for specific pin header locations. For LEDs, colored wires are positive ( + ). White or black wires are negative ( – ). If the LED does not light up when the system is powered on, try reversing the connection. For more information on connecting LEDs to your motherboard, see your motherboard user’s manual.

Note: Polarity (positive and negative) does not matter for switches.

3.5 REWIRINGMOTHERBOARDHEADERCONNECTIONS

There may come a time when you need to reconfigure the pin-outof a motherboard header connector. Examples could be for your USB header, audio input header, or some other front panel connector such as the Power Button connector.

Before performing any work, please refer to your motherboard user’s manual or your motherboard manufacturer's website to be sure of the pin-outneeded for your connector. We strongly recommend making a notated drawing before beginning work so that you can recover if your work gets disturbed.

1.Determine which wires you need to remove in order to rewire your plug to match the USB pin-outson your motherboard (refer to your motherboard user’s manual). Working on one connector at a time, use a very small flathead screwdriver or similar tool to lift up on the black tab located beside the gold posts (squares). This will allow you to easily slide out the pins from the USB plug.

2.Working carefully so as not to damage the wires, connectors, or pins, slowly remove the pin from the connector. Repeat these steps for each wire you need to change.

3.Working carefully so as not to damage the wires, connectors or pins, slowly reinsert the pin into the correct slot of the connector then snap closed the black tab that was lifted in step 1. Repeat these steps for each wire you need to change.

8

COOLINGSYSTEM

4.1TRICOOL™ EXHAUSTFAN

There is a 80 x 25mm TriCool™ fan pre-installedon theright-handside of the case. It has an external,three-speedswitch that allows you to choose between quiet performance, or maximum cooling. The default speed setting is Low.The fan is mounted so that air blows out of the case. There are externally accessible switches for these fans located at the rear of your case.

Size:

80 x 25mm TriCool™ fan

 

 

 

Rated Voltage:

12V

 

 

 

 

 

Operating Voltage:

10.2V - 13.8V

 

 

 

 

 

 

 

 

 

 

 

 

Speed

Input

Airflow

 

Static

Acoustic

Input

 

(RPM)

Current

 

Pressure

Noise

Power

 

 

 

 

 

 

 

 

 

 

 

 

High

0.2A

0.96 m³ / min

 

3.04mm-H2O

30 dBA

2.4W

 

2600

(Max.)

(34 CFM)

 

(0.12 inch-H2O)

 

 

 

 

 

 

 

 

 

 

 

 

 

Medium

0.15A

0.74 m³ / min

 

1.79mm-H2O

24.3 dBA

1.8W

 

2000

(26 CFM)

 

(0.07 inch-H2O)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Low

0.1A

0.55 m³ / min

 

1.0mm-H2O

18.05 dBA

1.2W

 

1500

(20 CFM)

 

(0.03 inch-H2O)

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: The minimum voltage to start a TriCool™ fan is 5V. We recommend that you set the fan speed switch to High if you choose to connect the fan(s) to a fan control device. A fan control device regulates the fan speed by varying the voltage, which may start as low as 4.5V to 5V. Connecting a TriCool™ fan set on Medium or Low to a fan-controldevice may result in the fan not being able to start because the already lowered voltage from the fan control device will be further reduced by the TriCool™ circuitry below 5V.

9