Antec HCG-620 User Manual

Size:
373.18 Kb
Download

HCG-620POWER SUPPLY

USERSMANUAL

USERSMANUAL

HCG SERIES

HCG-620POWER SUPPLY

HIGHCURRENTPOWER, LOWCOSTPOWERSUPPLY

The HCG-620,part of Antec’s High Current Gamer Series of power supplies, is the perfect combination of power and efficiency. Delivering 620 continuous watts of power, theHCG-620features ahigh-power+12V rail and specialheavy-dutyHigh Current connectors and cabling that supply extreme levels of power. At the same time, the HCG620 delivers superb efficiency thanks to its 80 PLUS® Bronze Certification and Active PFC.Highest-qualitygoldplated connectors,Japanese-brandcapacitors and quiet 135 mm double ball bearing fans complete the package.

STANDARDS ANDFEATURES

The connectors and power specifications of the HCG-620PSU are all compatible with ATX12V v2.3 and EPS12V v2.91 specifications. TheHCG-620features Universal Input, which automatically senses when you connect the power supply to any AC power source between 100~240V without setting a voltage switch. This power supply also features Active Power Factor Correction (Active PFC), which improves the power factor value of the power supply by altering the input current wave shape, helping to power transmission across the grid.

SYSTEMPROTECTION

A variety of industrial-gradesafety circuitry will help protect your computer: OVP (Over Voltage Protection), SCP (Short Circuit Protection), OPP and OCP (Over Current Protection). Sometimes the PSU will “latch” into a protected state. You will need to power off the PSU and clear the fault before it will function again. There are no userreplaceable fuses in yourHCG-620.

80 PLUS® CERTIFICATION

80 PLUS® certification is the most widely recognized independent standard in power supply efficiency. An 80 PLUS® certified power supply uses less energy and generates less heat to stay cooler, run quieter and last longer. The HCG-620has been 80 PLUS® Bronze certified to be at least 82% efficient at a wide range of operating loads; this will lower your operating costs and help protect the environment.

2

POWEROUTPUT& CONNECTORS

The HCG-620power supply distributes power on separate rails. Some rails require a minimum load in order to run. To see the output capacity and regulation for each different voltage, see Table 1. A list of all available power connectors can be found in Table 2.

TABLE1

 

 

Output Voltage

Load Max.

Regulation

Ripple & Noise

 

 

 

 

 

 

 

 

 

 

 

 

 

+3.3V

 

24A

±5%

< 50 mV

 

 

 

 

 

 

 

 

 

 

 

 

 

+5V

 

24A

±5%

< 50 mV

 

 

 

 

 

 

 

 

 

 

 

 

 

+12V

 

48A

±5%

< 120 mV

 

 

 

 

 

 

 

 

 

 

 

 

 

–12V

 

0.8A

±10%

< 120 mV

 

 

 

 

 

 

 

 

 

 

 

 

 

+5VSB

 

2.5A

±5%

< 50 mV

 

 

 

 

 

 

 

 

 

 

 

TABLE2

 

 

 

 

 

 

 

 

 

 

 

 

 

Quantity

 

Connector

 

Description

 

 

 

 

 

 

 

 

1

 

 

 

 

24-pin(20 + 4) main connector

 

 

 

 

 

 

 

 

1

 

 

 

 

8-pin(4 + 4) ATX12V / EPS12V

 

 

 

 

 

 

 

 

2

 

 

 

 

8-pin(6 + 2)PCI-E

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

SATA

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

Molex

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

Floppy

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTALLATION:

1. Install the HCG-620PSU into either the top or bottom of your case with the four screws provided. Refer to your case manual if you are unsure where the power supply should be installed.

2.Connect the 24-pin(20 + 4) main power connector to your motherboard. If your motherboard uses a20-pinconnector, detach the4-pinattachment on the24-pinconnector.

Note: The detachable 4-pinsection cannot be used in place of a4-pin+12V connector.

3.Connect the 8-pin(4 + 4) connector for the CPU.

Note: Please also refer to your motherboard user’s manual for any special instructions.

4.Connect the PCI-Econnector(s) to your graphics card(s).PCI-Egraphics cards use different amounts of power. For some, a single6-pinconnector is sufficient, while more powerful cards use multiple connectors, including the advanced8-pinPCI-Econnector. The8-pinPCI-Econnectors on theHCG-620can be used as either 6- or 8- pin connectors.

5.Connect all Molex/SATA connector(s) to your hard drives, optical drives (CD/DVD/BluRay™) and other accessories. Please note that some devices will use either the older 4-pinMolex connectors, while others will use the newer15-pinSATA connector.4-pinMolex connectors have two black wires, a yellow, and a red. The SATA connector has an additional orange power wire.

6.Connect your floppy drive if present using the supplied FDD connector shown in Table 2.

7.When you have all the connections secured, connect the AC power cord to the power supply AC inlet, making sure the use the heavy-dutycord supplied with yourHCG-620.

4

8.Turn the switch on the PSU to the “|” position.

5

Antec, Inc.

47900 Fremont Blvd.

Fremont, CA 94538

tel: 510-770-1200

fax: 510-770-1288

Antec Europe B.V.

Stuttgartstraat 12

3047 A Rotterdam

Netherlands

tel: +31 (0) 10 462-2060fax: +31 (0) 10437-1752

Technical Support:

US & Canada

1-800-22ANTECcustomersupport@antec.com

Europe

+31 (0) 10 462-2060europe.techsupport@antec.com

www.antec.com

© Copyright 2010 Antec, Inc. All rights reserved.

All trademarks are the property of their respective owners. Reproduction in whole or in part without written permission is prohibited.

6