AMX Endeleo Multi-Format Receiver UDM-RX02 User Manual
Size:
179.71 Kb
Download

Quick Start Guide

UDM-RX02 EndeleoMulti-FormatReceiver

Overview

Installed at the display device, the UDM-RX02(FG-UDM-RX02)converts the signal received from a UDMMulti-FormatDistribution Hub to standard A/V signals (FIG. 1).

Configuration

The UDM-RX02is configured via the UDM Hub’s WebConsole. Refer to the UDM Hub’sOperation/Reference Guide for details.

Rear Panel Components

All of the connectors and ports are located on the rear panel (FIG. 2):

 

 

UDM HUB port (RJ45) - from an

Composite (Pr) port

 

 

Composite (Pb) port

 

 

“OUTPUT” port on the UDM-0102

Composite (Y) port

 

 

 

 

VGA (HD15) port

 

 

 

 

 

 

 

 

 

 

 

S-Videoport

 

 

 

 

 

 

 

 

CVBS port

 

 

 

 

 

 

FIG. 1 UDM-RX02

 

 

 

Serial port (RJ12)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

With all the same features of the UDM-RX01,theUDM-RX02adds support for “Common” mode sync, as well as remote power for long cable distance runs.

Compatibility

The UDM-RX02is compatible for use with the following UDM Hubs:

UDM-0102(FG-UDM-0102)- This hub supports Common Synch Mode.

UDM-0404(FG-UDM-0404)- This hub supports Common Synch Mode.

UDM-1604(FG-UDM-1604C)- This hub supports Common Synch Mode.

UDM-1604(FG-UDM-1604)- This hub does not support Common Synch Mode. In this case, theUDM-RX02will function, but without Common Synch Mode.

Product Specifications

UDM-RX02Specifications

Power Requirements:

 

24VDC @ .75A

 

 

Note: In most cases theUDM-RX02is remotely powered

 

 

by the UDM Multi-FormatDistribution Hub (seePowering

 

 

on the UDM-RX02 ).

 

 

 

Rear Panel Connectors:

 

 

 

Power Socket:

2.1mm barrel-styleDC power socket (female)

 

 

UDM Hub (RJ45)

Provides audio/video transport as well as control via Cat5,

Port:

Cat5e or Cat6 to an UDM Hub.

 

 

Serial (RJ12) port:

Enables an administrator to control the various functions

 

 

to the UDM-RX02from a command line prompt and termi-

 

 

nal connection.

 

 

• Requires a DB9-to-RJ12adapter cable(FG-RS01)to

 

 

connect to a PC.

 

 

• 9600, 8 bit, No Parity, 1 Stop Bit

 

 

IR Rx Port:

3.5mm stereo input port, for connection of an IR receiver

 

 

to allow setup of the UDM-RX02,local compensation

 

 

controls, and remote control of centrally located IR

 

 

devices.

 

 

IR Tx Port:

3.5mm stereo IR Transmitter output port allows one IR-

 

 

controlled device (such as a DVD or VCR player) to be

 

 

controlled via optional wired IR emitter.

 

 

Audio Connectors:

• Black RCA female connector - Digital audio

 

 

• White RCA female connector - Analog audio Left

 

 

• Red RCA female connector - Analog audio Right

 

 

Video Connectors:

• Yellow RCA female connector - CVBS (supports

 

 

composite video)

 

 

S-Video-S-videofemale connector

 

 

• VGA - HD15 female connector (supports VGA video)

 

 

• Green RCA female connector - Component output: Y

 

 

• Blue RCA female connector - Component output: Pb

 

 

• Red RCA female connector - Component output: Pr

 

 

Operating Environment:

• 35°F - 95°F (5°C - 35°C)

 

 

• Max. relative humidity - 85% (non-condensing)

 

 

Dimensions (HWD):

1" x 8 15/16” x 3 3/8” (25 mm x 227 mm x 85 mm)

 

 

Weight:

1.45 lb. (658 g)

 

 

Certifications:

• CE

 

 

• FCC part 15 Class A

Other AMX Equipment: • RS232 DB9/RJ12 Connection Cable (FG-RS01)

UDM-RC02Multi-FormatIR Remote Control(FG-UDM-RC02)

IR01 IR Emitter Module (FG-IR01)

IR03 External IR Receiver Module (FG-IR03)

UDM-PS24VDC, 750mA Power Supply(FG-UDM-PS)

IR Rx port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RCA audio

IR Tx port

 

 

 

 

 

 

 

 

(left/right)

 

 

 

 

Power connector

 

 

SPDIF female Digital Audio port

 

 

FIG. 2 UDM-RX02- rear panel components

UDM Hub Port (RJ45)

The UDM-RX02connects to a UDM Hub through a Cat 5/Cat 6 connection. Refer to the UDM Hub’sOperation/Reference Guide for details.

Serial Port

The Serial port is available for diagnostic and troubleshooting purposes.

The Serial port on the UDM-RX02is an RJ12 connector, and requires aDB9-to-RJ12adapter cable(FG-RS01)to connect to a PC for Terminal control.

IR Receiver (IR Rx) Port

The IR Rx port is used to enable user control and the remote compensation of the video link to the UDM, using theFG-UDM-RC10and theFG-IR03.

Refer to the Protocols and IR Learningsection of the UDM Hub’s Operation/Reference Guidefor details for information on learning a device’s IR commands.

IR Transmit (IR Tx) Port

The IR Tx port issues IR commands from theUDM-RX02to a controlled display device (TV monitor or display). One IR display device can be connected to the UDMRX02 via the IR Tx port, and controlled via the UDM Hub’s WebConsole or via remote control.

Connecting an IR Device to the IR Tx Port

1.Connect an IR01 Endeleo IR Emitter Module (FG-IR01)to the IR Tx port on theUDM-RX02.

Note: Ensure the position of the device corresponds to the position assigned in the Devices option of the UDMHub’s WebConsole.

2.Run the other end of the IR Emitter cable to the device’s IR sensor, and attach the IR Emitter to the device’s sensor by removing the cover on the reverse side of the IR Emitter.

IR commands for each device on the system have to be learned by the UDM-0102in order to function properly. Refer to theProtocols and IR Learning section of the UDM Hub’sOperation/Reference Guide for information on learning a device’s IR commands.

AUDIO Connectors

The UDM-RX02provides standard Audio RCA output connectors for S/PDIF for digital audio, and LEFT/RIGHT for analog audio output (FIG. 2).

VIDEO Connectors

VGA Input at Display Device

1.Attach one end of the VGA cable to the VGA connector on theUDM-RX02.

2.Run the other end to the VGA connector on the display device. Connect firmly.

3.If appropriate connect audio to the audio connectors on the UDM-RX02.

Note: Ensure the UDM Hub port the RX02 is attached to is configured correctly within the Hub’s configuration software. Also ensure the correct Audio Type (Analog L/R, S/PDIF, or None) is selected for the relevant input.

Composite Input at Display Device

1.Attach the composite cable (normally yellow) to the CVBS connector on theUDM-RX02.

2.Run the other end of the composite cable to the Composite connector (normally yellow) on the display device. Connect firmly.

3.If appropriate connect audio to the audio connectors on the UDM-RX02.

SVideo Input at Display Device

1.Attach the SVideo cable to the 4-pinS Video connector on theUDM-RX02.

2.Run the other end of the SVideo cable to the SVideo connector on the display device. Connect firmly.

3.If appropriate connect audio to the audio connectors on the UDM-RX02.