AMX CB-TP5 User Manual

Size:
259.15 Kb
Download

Installation Guide

CB-TP5 Rough-InBox for 5" Wall/Flush Mount Touch Panels

Overview

The CB-TP5Rough-InBox is an optional accessory for 5” Modero® Wall/Flush Mount Touch Panels. TheRough-InBox allows the panel to be mounted directly to the studs/pre-walland includes a wall box and mounting screws.

Wall Mount panels (NXDs) are contained within a metallic outer housing (back box). This back box is not removed when installing the NXD into aRough-InBox. The back box isonly removed to gain access for the replacement of the Compact Flash component or upgrade to the VESA housing.

Specifications

CB-TP5(FG038-10)Specifications

Dimensions (HWD)

• 3

3/4" x 5 1/4" x 3 3/8"

 

• 9.6 cm x 13.3 cm x 8.6 cm

 

 

 

Included

• 4

Phillips pan-head(#4-40x 0.375 Black) screws(80-0115)

Accessories

4

Phillips pan-head(#4-40x 0.625 Black) screws(80-0118)

 

 

 

Certifications

cTUVus Listed

 

 

 

 

WARNING: INSTALLER, LEAVE A GAP BETWEEN THE STUD ANDROUGH-INBOX TO ACCOMMODATE THE DRYWALL/SHEETROCK.

This gap allows the installation of the drywall/sheetrock after the CB-TP5has been mounted onto the beams. Therough-inbox installation must be done prior to any wall installation.

Note: The most important thing to remember when mounting thisrough-inbox is that the mounting tabs must be mounted flush against the outside of the sheetrock.

It is recommended that you cut out the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments.

The wiring knockouts on the left side will be used for the NXD-CV5Wall Mount panel connectors, so always secure therough-inbox to the stud using the Stud Mounting Holes on the right side of the box.

Pre-WallInstallation of theCP-TP5Rough-InBox

Refer to the SP226101 diagram for detailed installation dimensions.

Cutting out the surface slightly smaller than what is outlined in the installation drawings, in order to make any necessary cutout adjustments, is highly recommended.

The wiring knockouts on the left side will be used for the NXD-CV5Wall Mount panel connectors, so always secure therough-inbox to the stud using the Stud Mounting Holes on the right side of the box.

1.Rest the right Stud Mounting tabs onto the stud (keeping the knockouts on the left). Be sure to leave enough of a gap between the stud and NXD Mounting tabs to accommodate the installation of the drywall or sheetrock after the rough-inbox has been mounted. Ultimately, the Mounting Tabs should lie flush against the outside of the sheetrock.

2.Fasten the CB-TP5rough-inbox to the stud through the holes on the right Stud Mounting tabs(FIG. 1), using either nails or screws.

 

 

Rough-InBox

 

Do Not Use these

 

 

 

Stud

tabs to mount

 

 

 

 

 

the Rough-InBox

 

 

 

6X Knockout for 1/2” conduit fitting

Front surface of mounting tabs should be flush with outside face of drywall

Drywall

FIG. 1 CB-TP5- Drywall Installation

3.Remove the wiring knockouts from the left side of the CB-TP5to accommodate the cables being threaded through to the NXD touch panel.

Note: Remember that when mounting thisrough-inbox, the NXD mounting tabs must lie flush against the outside of the sheetrock.

4.Thread the incoming power, RJ-45audio/video, Ethernet, and USB wiring through the knockouts (use of the left wiring knockouts are recommended with this installation). Leave enough slack in the wiring to accommodate any repositioning of the panel.

5.Install the drywall/sheetrock before inserting the main NXD unit into the CB-TP5.

Recommended Cutout for CB-TP5Rough-InBox

Top

Bottom

Do Not Use These Tabs

To Mount Rough-InBox

Front

Do Not Use These Tabs

To Mount Rough-InBox

Left

Right

 

 

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

93-038-10

REV: A

 

10/08

©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com