AMX CB-MVPWDS User Manual

Size:
211.17 Kb
Download

Installation Guide

CB-MVPWDS Rough-InBox forMVP-WDSWall Docking Station

Overview

The CB-MVPWDSRough-InBox allows theMVP-WDSto be installed in a solid surface (e.g., wall or podium). ThisRough-Inbox includes a removable access plate to provide better access to wiring. TheCB-MVPWDSis symmetrictop-to-bottom, so the access plate may be installed at the top or the bottom.

Specifications

CB-MVPWDS(FG037-10)Specifications

Dimensions (HWD):

• 8 3/16" x 12" x 3 1/4"

 

• 20.7 mm x 30.4 mm x 8.2 mm

 

 

Included Accessories

• Five mountings screws (#4-24X .188, PFH, BLK,

 

TYPE B, SELF-TAPPING,SHT MTL)

 

(80-0203-01)

 

 

Certifications:

• cTUVus Listed

 

 

WARNING: INSTALLER, LEAVE A GAP BETWEEN THE STUD ANDROUGH-INBOX TO ACCOMMODATE THE DRYWALL/SHEETROCK.

This gap allows the installation of the drywall/sheetrock after the CB-MVPWDShas been mounted onto the beams. The stud notching andRough-InBox installation must be done prior to any wall installation.

Note: The most important thing to remember when mounting thisRough-InBox is that the mounting tabs must be mounted flush against the outside of the sheetrock. This step determines whether or not the mounting stud is notched

(cutout-outto fit theRough-InBox).

Installing the CB-MVPWDSRough-InBox

The CB-MVPWDS(FG037-10)is a metallicRough-InBox that can be secured to a stud in apre-wallsetting. TheMVP-WDScan then installed into theRough-InBox.

Note: Installation procedures and configurations vary depending on the installation environment.

When mounting the Rough-InBox, theMVP-WDSMounting Tabs must lie flush against the outside of the sheetrock.

Refer to SP596502 for detailed installation dimensions (see reverse).

It is recommended that you cut out the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments.

The CB-MVPWDScan be installed with the removable access panel positioned either on top or bottom. The access panel provides convenient access toin-wallwiring and must bere-installedprior to mounting theMVP-WDS.

1.Place the left side of the Rough-InBox on a stud, making sure that five Stud Fastening Holes and removable Access Panel are oriented correctly (installation dependent). Be sure to leave enough of a gap between the stud and Mounting Tabs to accommodate the installation of the drywall or sheetrock after theRough-InBox has been mounted. Ultimately, the Mounting Tabs should lie flush against the outside of the sheetrock.

Note: Although there are wiring knockouts are on both sides of theRough-InBox, the knockouts on the right side will be used for theMVP-WDS(wall docking station) connectors, so always secure theRough-InBox to the stud using the Stud Mounting Holes on the left side of the box.

2.Using either nails or screws, fasten the Rough-InBox to the stud through the five Stud Fastening Holes.

3.Remove the wiring knockouts from the right side of the Rough-InBox to accommodate cabling to theMVP-WDS.

4.Thread the USB and Power cables through the knockouts on the right of the Rough-InBox. It is recommended that you test these connections before fully installing the WDS.

5.Install the drywall/sheetrock before inserting the MVP-WDSinto theRough-InBox.

Stud

Removable Access Panel

Stud Fastening Holes (5 located on left panel)

Wiring knockouts

(right side ofRough-InBox)

Drywall or sheetrock

MVP-WDSmounting tabs (should lie flush against the outside of the wall)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

93-037-10

REV: A

 

10/08

©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com