AMX 16-Channel Custom Panel Interface AXP-CPI16 User Manual
Size:
198.64 Kb
Download

Operation/Reference Guide

AXP-CPI16

16-ChannelCustom Panel Interface

Custom Panel Interfaces

Last Revised: 1/13/2009

AMX Limited Warranty and Disclaimer

AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions:

Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year.

Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one

(1) year.

AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.

Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.

AMX Software is warranted for a period of ninety (90) days.

Batteries and incandescent lamps are not covered under the warranty.

This warranty extends only to products purchased directly from AMX or an Authorized AMX Dealer.

All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-dayperiod. After the30-dayperiod the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a valid RMA number.

AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a third party or by an AMX Dealer for a third party.

This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury.

Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY.

 

Table of Contents

Table of Contents

 

Product Information ...........................................................................................

1

Specifications............................................................................................................

1

Installation ..........................................................................................................

3

Mounting Dimensions ...............................................................................................

3

Setting the AXlink Device Number ...........................................................................

4

Preparing/connecting captive wires................................................................................

4

Connecting the Two 20-pin Headers ........................................................................

4

Switch Wiring Diagrams............................................................................................

5

Connecting the AXlink Wiring...................................................................................

5

Programming ......................................................................................................

7

Testing the Unit ........................................................................................................

8

AXP-CPI16 System Worksheet ...........................................................................

9

AXP-CPI1616-ChannelCustom Panel Interface

i

 

 

Product Information

Product Information

The AMX AXP-CPI1616 Channel Custom Panel Interface Board(FIG. 1) simplifies the process of creating custom control panels for Axcess systems. Providing contact closure inputs and feedback outputs for up to 16 buttons, the miniature PC board contains a20-pinheader for ribbon cable installation or for direct mounting to a printed circuit board.

AXlink

Connector

Pin 1

20-PinHeader P3

Connect this side to the ribbon cable

Pin 1

evice

IP Switch

AXlink Status LED

-PinHeader P2

nnect this side to the ribbon cable Connect this side to the PC board

FIG. 1 AXP-CPI16components

Specifications

The following table lists product specifications for the AXP-CPI16.

AXP-CPI16Specifications

Dimensions (HWD)

2.75" x 1.75" x 0.062" (69.90 mm x 44.50 mm x 1.557 mm)

 

 

Power

• Input voltage: 12 VDC (nominal)

 

• Current draw: 25mA

 

 

Inputs

16 closure inputs with a common ground (GND)

 

 

Outputs

16 open-collectoroutputs, acting as switch to ground, up to 100 mA DC each for:

 

• Board is not to supply more than 750 mA of +12V total.

 

• Small incandescent lamps

 

• LED indicators - with series resistor (1K for 12 VDC)

 

• Relays - with DC coil

 

 

AXlink Connector

A 4-pin(male) connector attached to afour-wirecable which sends control data from the

 

Axcess CardFrame to the AXP-CPI16.

 

 

Headers

Two 20-pinheaders included for ribbon cables (up to 100 feet each) or for mounting

 

directly to a PC board.

 

 

AXP-CPI1616-ChannelCustom Panel Interface

1

 

 

AXP-CPI16Specifications (Cont.)

AXlink Status LED

Indicates AXlink communication status as follows:

 

• One blink per second communication is functioning.

 

• Two blinks per second devices specified in the master program do not match the

 

specified devices found.

 

• Three blinks per second indicate an AXlink communication error.

 

Full-onindicates there is no AXlink control or activity (but power is on), or the Axcess

 

program is not loaded.

 

 

Device DIP Switch

8-positionDIP switch sets AXlink device ID.

 

 

Cables

Two 3-foot(91.4 cm) ribbon cables each with a female20-pinheader.

 

 

2

AXP-CPI1616-ChannelCustom Panel Interface