American Standard 2808.222, 2908.222 User Manual

0 (0)

Installation

Instructions

T M

2808.222

2908.222

Widespread Lavatory Faucet with the

Speed Connect™ Drain

Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature found only on

American Standard faucets.

Speed Connect Drain*

1/3 of the parts, installs in 1/3 of the time

No tools needed

Never needs adjustment

Guaranteed to seal properly the first time, every time.

Certified to comply with ANSI A112.18.1

US60385 Rev. 1 . 2

*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for removing your current drain can be found in the Troubleshooting section of these instructions.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Recommended tools

 

 

 

Screwdriver

Channel Locks

Adjustable Wrench

Tubing Cutter

1

 

INSTALL SPOUT

CAUTION

Turn off water at

 

 

 

 

 

 

 

 

main supply.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure

Fig. A.

 

 

 

 

the SEAL WASHER (3) is properly seated in SPOUT (1).

 

 

 

 

 

 

 

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

 

 

 

 

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

 

 

 

 

 

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

 

 

 

 

1

 

 

 

 

 

Tighten LOCKNUT (6) firmly. Fig. A.

3

7

1A INSTALL VALVE BODY

Place RUBBER RING (9) into ESCUTCHEON (10).

Install LOCKNUT (11) onto VALVE BODY (12).

 

4

 

 

From under side of mounting surface, install VALVE BODY (12) through valve

SLOT

5

mounting holes. Threads of VALVE BODY (12) should extent at least 5/16

 

 

of a inch above mounting surface top. Fig. B.

 

6

Important: Thread ESCUTCHEON (10) onto VALVE BODY (12) until snug against

 

 

 

internal stop. This is key to the installation. If not done, the faucet handles won’t

 

2

work correctly. If necessary, adjust LOCKNUT (11).

 

Hand tighten LOCKNUT (11) to secure VALVE BODY (12).

Repeat above steps for opposite VALVE BODY (12A).

10

 

 

9

10

1

5/16'' MIN.

9

 

MOUNTING

 

 

12a

SURFACE

 

Fig. B.

11

12

12

 

11

 

 

2808 SERIES

1

American Standard 2808.222, 2908.222 User Manual

2 INSTALL POP-UP DRAIN

Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A.

Drop DRAIN BODY (4) through sink drain hole. Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4). Fig. B.

Note: No plumber’s putty or caulk is required.

The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B.

Fig. A.

Fig. B.

REAR OF

 

 

SINK

1

 

 

3

 

4

 

 

6

 

 

5

2

 

SINK

 

DRAIN

 

 

HOLE

3 INSTALL BLACK GASKET

Install BLACK CONE GASKET (1) onto DRAIN BODY (2) from below.

Note: The flat side of the BLACK CONE GASKET (1) must face down.

2

1

FLAT SIDE OF GASKET MUST FACE DOWN

4

INSTALL GRAY LOCKNUT

Fig. A.

 

Fig. B.

 

Install GRAY LOCKNUT (1) onto DRAIN

 

 

 

 

BODY (2) from below SINK. Fig. A.

 

 

 

 

Note: The flat side of the GRAY LOCKNUT (1)

 

 

 

 

must face up.

 

2

 

 

Tighten firmly by hand. No tools are required.

 

 

DRAIN

 

Check DRAIN FLANGE in SINK to ensure that

 

 

FLANGE

 

WHITE FOAM GASKET (3) is fully compressed

 

 

FLAT SIDE OF

 

and not visible. Fig. B.

 

 

GRAY LOCKNUT

 

 

 

MUST FACE UP

 

 

 

1

3 WHITE FOAM

 

 

 

 

 

 

 

 

GASKET

 

 

 

 

NOT VISIBLE

5

POP-UP KNOB

 

 

DOWN

 

POP-UP KNOB (1) must be fully down.

 

 

 

 

 

 

 

1

US60385 Rev. 1 . 2

2

Loading...
+ 2 hidden pages