INSTALLATION |
For These Two-Piece Toilets: |
|
INSTRUCTIONS |
Ellisse 2184 |
Deco 2059 |
|
Heritage 2176 |
Cadet III 13L 2650/2660 |
|
Baby Devoro 2315 |
Sonoma 2454 |
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
! CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife |
Regular Screwdriver |
Adjustable Wrench |
Sealant |
Tape Measure |
Hacksaw |
Wax Ring/Gasket |
Flexible Supply Tube |
Closet Bolts |
Carpenters Level |
1REMOVE OLD TOILET
a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!
2 |
|
ROUGHING-IN DIMENSIONS: |
||
|
|
NOTE: Distance from wall to closet flange centerline must |
||
|
||||
|
|
be as listed below: |
||
|
|
|
|
For 4110 Tanks: A = 10" (254mm) |
|
|
FINISHED WALL |
For 4114 Tanks: A = 14" (356mm) |
|
|
|
|
|
|
|
|
|
|
For all other Tanks: A = 12" (305mm) |
|
|
|
|
|
SUPPLY
AS
REQ'D.
FINISHED
FLOOR
3
CLOSET FLANGE
A
CLOSET BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90° , and slide into place 6" (152 mm) apart and parallel to wall.
4
SEALANT |
WAX RING |
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.
5 |
|
6a |
|
|
NUT |
|
|
|
TAPERED |
|
|
|
WASHER |
|
|
|
CLOSET |
|
|
|
BOLT |
|
|
|
FLANGE |
|
|
POSITION TOILET ON FLANGE |
CLOSET FLANGE |
||
a. |
Unplug floor waste opening and install toilet on closet flange |
||
|
|||
|
so bolts project through mounting holes. |
|
|
b. |
Loosely install retainer washers and nuts. Side of washers |
|
|
|
marked "THIS SIDE UP" must face up! |
|
INSTALL TOILET
Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.
!CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
S A V E F O R F U T U R E U S E
Saniwares
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © A m e r i c a n S t a n d a r d I n c . 2 0 0 0
730513-100 REV. D
6b |
INSTALL BOLTS AND CAPS |
|
|
BOLT CAP |
|
|
|
Ellisse 2184 |
|
CLOSET |
Baby Devoro 2315 |
|
Deco 2059 |
|
|
BOLT |
Cadet III 13L 2650/2660 |
|
|
|
|
|
Sonoma 2454 |
WASHER NUT
a.Install caps on washers. (If necessary, cut bolt height to size before installing caps.)
b.Smooth off the bead of sealant around base. Remove excess sealant.
COVER |
COVER |
HERITAGE 2176 |
MTG. CLIP |
|
|
|
|
CLOSET |
|
|
BOLT |
WASHER |
NUT |
|
|
|
a.Press covers over mounting clips. (If necessary, cut bolt height to size before installing covers.)
b.Smooth off the bead of sealant around base. Remove excess sealant.
7a
For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed).
TANK MTG. |
RUBBER |
|
GASKET |
||
BOLTS PRE- |
||
|
||
INSTALLED |
|
WASHER
NUT
INSTALL TANK
a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washers and nuts.
b.With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
! CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
7b
For all other Tanks/Bowls
RUBBER
WASHER
RUBBER TANK MTG. GASKET
BOLTS
WASHER
NUT
INSTALL TANK
a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening.
b.Insert tank mounting bolts and rubber washers from inside tank, through mounting holes, and secure with metal washers and nuts.
c.With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
! CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
8 |
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. |
|
9a |
Before continuing, determine the type of water supply connecation you have from |
9b |
|||||||
|
|
the chart below and use the appropriate assembly parts required to properly |
|
||||||
|
|
reconnect the water supply. DO NOT use plumber's putty to seal these fittings. |
|
||||||
|
|
METAL/COPPER |
METAL FLANGED |
METAL SPIRAL |
VINYL/BRAIDED |
|
|||
|
|
FLARED TUBING |
TUBING |
TUBING |
CONNECTOR |
|
|||
|
|
LOCK NUT |
LOCK NUT |
LOCK NUT |
LOCK NUT |
|
|||
|
|
CONE |
EXISTING |
EXISTING |
COUPLING |
|
|||
|
|
WASHER |
|
||||||
|
|
WASHER |
CONE |
NUT |
|
||||
|
|
COUPLING |
EXISTING |
WASHER |
|
|
|
||
|
|
|
|
|
|
||||
|
|
COUPLING |
COUPLING |
|
|
|
|||
|
|
NUT |
|
|
|
||||
|
|
|
NUT |
NUT |
|
|
|
||
|
|
WATER |
WATER |
WATER |
WATER |
|
|||
|
|
SHUT-OFF |
SHUT-OFF |
SHUT-OFF |
SHUT-OFF |
|
|||
These parts must be used as |
Use existing |
Use existing spiral |
Captive cone |
|
|||||
illustrated to insure water-tight |
coupling nut |
cone washer. |
washers already |
|
|||||
connection. Use of existing |
and washer. |
Fluidmaster cone |
included. No |
|
|||||
coupling nut may result in |
|
|
|
washer may not |
additional washers |
|
|||
water leakage. Water supply |
|
|
|
seal completely on |
needed. |
|
|||
tube or pipe must extend at |
|
|
|
spiral type supply |
|
|
|
||
least 1/2" inside threaded |
|
|
|
line. |
|
|
|
||
shank of valve (does not apply |
|
|
|
|
|
|
|
||
to flanged tubing). |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|||
|
CAUTION: DO NOT USE |
|
|
CAUTION: Overtightening of |
|
|
|||
|
CONE WASHER WITH |
|
|
LOCK NUT or COUPLING NUT |
|
|
|||
|
|
|
could result in breakage and |
|
|
||||
|
PLASTIC SUPPLY LINE. |
|
|
potential flooding. |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
With correct washers in place (see Step 9a), tighten COUPLING NUT 1/4 turn beyond hand tight. DO NOT OVERTIGHTEN.
- 2 - |
730513-100 REV. D |
|