American Standard 7055.115, 7056.105, 7055.105, 7056.205, 705.205 User Manual

...
0 (0)
American Standard 7055.115, 7056.105, 7055.105, 7056.205, 705.205 User Manual

Product No.'s & Options

1

Specifications

2

How to Install

2-3

Maintenance

3-7

FAQ,s

7-8

Replacement Parts

8

Certified to comply with ASME A112.18.1M

© 2012 American Standard

1. Remove the fitting and loose items from the carton.The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.

3a. AC Power Supply (7056 Series)

 

6

DO NOT REMOVE

 

 

 

DO NOT REMOVE

PROTECTIVE

 

 

 

PROTECTIVE FILM

FROM SENSOR

 

 

 

FROM SENSOR EYE

UNTIL INSTALLATION

 

 

 

UNTIL INSTALLATION

IS COMPLETE

 

 

 

IS COMPLETE.

3

3

 

 

 

 

 

 

 

 

 

 

 

3a

 

3a

7

8

7

8

 

 

© 2012 American Standard

 

© 2012 American Standard

 

2

705P400

4

1

M965255 REV. 1.6

 

Roughing-in Dimensions

Fig. 1

FINISHED WALL

OR BACKSPLASH

MIN. 1" CLEARANCE

38mm (1-1/2 )

457mm

(18)

3/8" COMPRESSION CONNECTORS

MOUNTING

SURFACE

32mm (1-1/4)

GENERAL DESCRIPTION:

Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery) or AC power. Inlets 3/8" compression, built-in checks, flexible stainless steel 18" reach inlet hoses for spout connection and In-line integral strainer for solenoid.

TOOLS REQUIRED; Fig. 2

1

Hex Wrench (Included)

4

Phillips Screwdriver

2

Adjustable Wrench

5

Tape Measure

3

Plumbers' Putty or Caulking

 

 

INSTALLATION

1 INSTALL SPOUT ASSEMBLY;

Fig. 1 CAUTION Turn off hot and cold water supplies before beginning

1.Make sure O-RING SEAL (9) is installed.

2.Installation with ESCUTCHEON (1) (optional).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1). (Only if mounting surface is uneven).

3.Insert supply HOSES (2), SHANK (3) and POWER CORD

(10)(if equipped) through hole in ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions below to secure faucet to mounting surface.

(Make sure PIN (7) is in back).

4.Installation less ESCUTCHEON (1). IMPORTANT: Do not use putty when installing faucet without escutcheon.

5.Assemble RUBBER WASHER (4), BRASS WASHER

(5)and THREADED LOCKNUT (6) onto SHANK (3) from underside of sink or mounting surface. Hand tighten LOCKNUT (6).

6.Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws slightly each time until all are snug to ensure even pressure.

2 CONNECT POWER SUPPLY; Fig. 1a

(7056 series only)

1.Connect the sensor cable (1) to the POWER SUPPLY CABLE (2).

2.Code approved Electrical Outlet provided by others. (120V 50/60 Hz)

3.Plug AC POWER SUPPLY (3) into Outlet.

Fig. 2

3

 

2

 

4

5

10'

 

Fig. 1

IMPORTANT: Do not

 

 

 

use putty when installing

 

 

 

faucet without escutcheon.

7

PUTTY

9

(If required)

 

 

 

 

 

 

3

 

1 (OPTIONAL)

 

10

 

MOUNTING

 

 

 

 

SURFACE

 

2

 

TIGHTEN

 

 

 

SPIN NUTS

4 58

6

2

M965255 REV. 1.6

 

Loading...
+ 6 hidden pages