BARRIER FREE
PIAZZA™ COUNTERTOP SINK
VITREOUS CHINA
PIAZZA™ COUNTERTOP SINK
•Made from vitreous china
•Self-rimming with cutout template supplied
•Large faucet deck and generous bowl
•Front overflow
0478.403 Faucet holes on 4" (203mm) centers
0478.803 Faucet holes on 8" (102mm) centers (illustrated)
0478.001 center hole only
Nominal Dimensions:
23-1/2" x 18-3/8"
(597 x 467mm)
Bowl sizes: |
|
|
|
|
18-1/2" (470mm) wide |
FINISHED WALL |
(203mm) |
(70mm) |
|
11-3/4" (299mm) front to back |
|
|
||
|
OR SPLASHBACK |
8" |
2-3/4" |
OPTIONAL |
6-1/2" (165mm) deep
Compliance Certifications - Meets or Exceeds the Following Specifications:
•ASME A112.19.2M for Vitreous China Fixtures
•CAN/CSA B45 series
To Be Specified: |
|
Color: White |
Bone |
Linen |
Silver |
Fawn Beige Black
Faucet*:
Faucet Finish:
Supplies:
1-1/4" Trap:
7"
(178mm)
18-3/8" (467mm)
SEALING |
23-1/2" |
|
|
COMPOUND |
3/4" |
||
COUNTERTOP |
(597mm) |
||
(19mm) |
|||
|
|||
(BY OTHERS) |
|
|
|
|
|
7-3/4" |
|
*10-3/4" |
|
(197mm) |
|
|
|
||
(273mm) |
|
|
|
*12-7/8" |
|
|
|
(327mm) |
|
SUPPLIES |
|
|
|
AS REQ'D |
|
|
8" |
31" |
|
|
(787mm) |
||
|
(203mm) |
||
|
SUGGESTED |
||
|
|
||
|
|
1-1/4" O.D. WASTE |
|
|
|
33-1/4" |
|
|
|
1-1/4" O.D. TAILPIECE (845mm) |
|
FINISHED FLOOR |
|
|
51mm
(2)
845mm (33-1/4)
686mm
(27)
MIN.
610mm
(24)
203mm |
|
|
|
DRAWING FOR |
(8) |
|
|
|
DIMENSIONAL |
|
|
|
||
|
|
|
PURPOSES ONLY. |
|
MIN. |
|
|
|
IT IS NOT AN EXACT |
REPRESENTATION.
152mm
(6)
MAX.
BARRIER FREE
CLEARANCE 229mm
(9)
MIN.
* See faucet section for additional models available
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 ACCESSIBLE AND USABLE BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Install lavatory 864mm (34") from finished floor. Lavatory installed 51mm (2") minimum from front edge of countertop provides 686mm (27") knee clearance.
NOTES:
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
|
J38 |
|
|
© 2008 AS America Inc. |
Revised 2/08 |
||
|
Loading...