American Standard 2305.100, 2305.156 User Manual

0 (0)
American Standard 2305.100, 2305.156 User Manual

MADERA™16-1/8” HEIGHT

ELONGATED FLUSH VALVE TOILET

BARRIER FREE

VITREOUS CHINA

MADERA™ 16-1/8” HEIGHT 10” ROUGH TOILET

Vitreous china

Low-consumption (6.0 Lpf/1.6 gpf)

Elongated bowl

Fully glazed 2” ballpass trapway

10” x 12” water surface area

Direct-fed siphon jet action

10” Rough-in

1-1/2" inlet spud

2 bolt caps

100% factory flush tested

2305.100 Top spud

2305.156 Top spud with slotted rim for

bedpan holding

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.2M (and 19.6M) for Vitreous China Fixtures - includes Flush Performance, Ball Pass Diameter, Trap Seal Depth and

all Dimensions

Nominal Dimensions: 778 x 381 x 409mm (30-1/2" x 15" x 16-1/8")

Fixture only, seat and flush valve by others.

Recommended working pressure--between 25 psi at valve when flushing and 80 psi static

To Be Specified

Color: White Bone Silver Shell Black

Seat: Olsonite #95 open front seat less cover

Seat: Church #9500C open front seat less cover

Flush Valve: Sloan Royal #111 or equal

FINISHED WALL

 

 

 

 

 

 

775mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(30-1/2)

 

 

 

 

 

 

 

 

102mm

 

 

 

470mm

 

(4)

 

 

 

(18-1/2)

 

 

 

 

 

 

38mm

C/L OF SEAT POST HOLES

 

 

 

 

 

 

 

 

 

 

( 5 - 1/2 CENTERS)

 

 

(1-1/2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1" N.P.T. OR 1" C.W.T. SUPPLY TO FLUSH VALVE

121mm

(4-3/4) 702mm (27-5/8)

394mm (15-1/2)

1 - 1/2 SPUD

410mm (16-1/8)

 

 

 

 

 

 

 

 

 

 

 

356mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(14)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

127mm

FINISHED FLOOR

 

 

235mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13mm

(5

 

 

 

 

(9-1/4)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1/2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

254mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(10)

 

 

 

 

 

 

C/L OF OUTLET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTES:

TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON THE FLUSH VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR SUPPLY ROUGHING.

THIS TOILET DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 254MM (10”) FROM FINISHED WALL TO C/L OF OUTLET.

FLUSH VALVE NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance established by ANSI Standard A112.19.2

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

● When installed so top of seat is 432 to 483mm (17" to 19") from the finished floor.

MEETS THE AMERICAN DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USEABLE BUILDING FACILITIESCHECK LOCAL CODES.

CI-6

© 2003 American Standard Inc.

Revised 5/03

 

Loading...