American Standard ERVR100A9P00A, ERVR200A9P00A, ERVR300A9P00A User Manual

0 (0)
32-5042-02
User’s Information Guide
Energy Recovery Ventilator (ERV)
*ERVR100A9P00A
*ERVR200A9P00A
*ERVR300A9P00A
*May be "A" or "T"
32- 5042- 02
2 32-5042-02
User’s Information
Understand the signal words. WARNING, AND
CAUTION. These words are safety alert words.
WARNING indicates hazards which could result in
personal injury or death. CAUTION is used to
indicate unsafe practices which could result in minor
injury or property damage.
WARNING
!
Disconnect Power Before Servicing. Failure to
follow the electrical servicing instruction may
cause Personal Injury or Death.
WARNING
!
Do Not Use This Unit if Any Part Has Been
Under Water.
Immediately Call A Qualified Service
Technician To Inspect The ERV and To Replace
Any Part of The Control System Which Has
Been Under Water.
CAUTION
!
PERSONAL INJURY HAZZARD
Failure to follow filter service instructions may
cause personal injury. The access door swings
down when unit is installed overhead.
Carefully hold the access door while unlatching
and lowering. The door should be removed
prior to performing filter service.
FILTER SERVICE.
A Clean Filter Saves Money.
When the ERV provides fresh outdoor air into your
home and exhausts indoor air to the outside, dust and
dirt particles build up on the air filters. Excessive
accumulation can block airflow, decreasing the ERV’s
performance and increase energy usage. To maintain
top performance be sure to clean or replace the ERV
filters according to the instructions in this manual.
Clean filters every three months when the unit is in
regular use or as needed to keep them clean.
How to remove and clean your filter:
1. Release cam latches and carefully swing access
door open. The access door may be removed for ease
of service by sliding the access door off. Use caution
when removing door
2. Remove the filter retainer springs. Pull the filters
out. See Figure 1.
3. Vacuum filters off with a hose attachment.
4. Re-install filters and retainer spring
5. Re-install cover, and fasten cam latches.
FILTER SERVICE NOTES
A) The filters should be replaced after they have been
cleaned several times. Contact your installing dealer
for service and replacement filters. Replacement
filter model numbers are as follows:
Model Filter #
*ERVR100 BA YFLT10A1010A
*ERVR200 BA YFLT20A1020A
*ERVR300 BA YFLT20A1020A
B) Filters may be cut from a sheet or roll of ¾” - 1”
firm, spun polyester filter “hog hair” media or
material, similar to the existing, factory installed,
green/blue filter in the unit.
The size of each filter (2 required per unit) is listed as
follows:
*ERVR100 10 ½ ” x 1 0 ½
*ERVR200/300 1 0 ½ x 21 ¾
* First letter of model number may be an “A” or “T”.
C) Filters must always be used during unit
operation or the heat transfer core will become
blocked by particulate matter. The filters supplied in
the unit are typically able to keep the heat transfer
core clear for many months. Finer filters may be
used but must be cleaned more often.
HEA T TRANSFER CORE SERVICE.
(The Heat Transfer Core may also be referred to as
the Energy Exchange Element or Heat Exchanger)
Vacuum the Face of the Heat Transfer Core
Yearly.
Particulate matter collects only on the entering faces
of the heat transfer core. The interior of the heat
transfer core stays clean even if the element faces
are covered particulates.
TO CLEAN THE HEAT TRANSFER CORE:
1. Remove filter retainer spring and the filters (see
above).
2. Vacuum the exposed faces of the heat transfer
core with a soft brush attachment.
3. After servicing the filters, re-install them and the
filter retainer spring (see above).
4. Vacuum out dust from the rest of the unit case.
CAUTION
!
DO NOT WASH THE HEAT TRANSFER CORE.
Always handle the core carefully. Keep it away
from water or fire to avoid damaging it. The
heat transfer core can be replaced but is
expensive.
Loading...
+ 4 hidden pages