American Standard 3 2829, 2386, 2383, 3 2838, 2384 User Manual

0 (0)
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE
CADET® 3 - 1.6 GPF TWO-PIECE TOILET
Models 2383 / 2384 / 2386 / 2447 / 2431 / 2880 / 3305
CADET® 3 FloWise™ - 1.28 GPF TWO-PIECE TOILET
Models 2829 / 2832 / 2835 / 2838 / 2880 / 3305
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl. b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply! c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases. d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!
ROUGHING-IN DIMENSIONS:
2
NOTE: Distance from wall to closet flange centerline must be as listed on chart:
FINISHED WALL
SUPPLY
AS
REQ'D.
FINISHED FLOOR
A
43
CLOSET FLANGE
A
CLOSET
BOLTS
SEALANT
WAX RING
MODELS
2383.010 2384.010
10"
2386.010
ROUGHS
2383.012
2386.012
2384.012
12"
3305.000
ROUGHS
2431.012
2447.000
2880.000
2383.014 2384.014
14"
2386.014
ROUGHS
2829.128
2832.128
2835.128
2838.128
2447.128
2880.128
5
DIMENSION “A”
254mm (10)
305mm (12)
356mm (14)
NUT
CLOSET
BOLT
TAPERED WASHER
SAVE FOR FUTURE USE
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide into place 6" (152mm) apart and parallel to wall.
Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2008
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.
FLANGE
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. b. Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up!
730928-100 Rev. F
6
7
For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed).
BOLT CAP
CLOSET FLANGE
WASHER
NUT
CLOSET BOLT
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.)
c. Smooth off the bead of sealant around base. Remove excess sealant.
TANK MTG. BOLTS PRE­INSTALLED
WASHER/
NUT
COMBO
RUBBER GASKET
INSTALL TANK
a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washer/nut combo.
b. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.
*
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
8
9a
Before continuing, determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL / COPPER
FLARED TUBING
CONE WASHER
COUPLING NUT
WATER SHUT-OFF
These parts must be used as illustrated to insure water-tight connection. Use of existing coupling nut may result in water leakage. Water supply tube or pipe must extend at least 1/2" inside threaded shank of valve (does not apply to flanged tubing).
CAUTION: DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE.
METAL FLANGED
TUBING
EXISTING WASHER
EXISTING COUPLING NUT
WATER SHUT-OFF
Use existing coupling nut and washer.
METAL SPIRAL
TUBING
WATER SHUT-OFF
Use existing spiral cone washer. Fluidmaster cone washer may not seal completely on spiral type supply line.
EXISTING CONE WASHER
COUPLING NUT
VINYL / BRAIDED
CONNECTOR
Captive cone washers already included. No additional washers needed.
CAUTION: Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding.
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING NUT
WATER SHUT-OFF
9b
With correct washers in place (see Step 9a), tighten COUPLING NUT 1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
- 2 -
730928-100 Rev. F
Loading...
+ 2 hidden pages