INSTALLATION INSTRUCTIONS
BOULEVARD® Dual Flush One-Piece Toilet Model 2891-Elongated Right Height® with Seat
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years.To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
Certified by
IAPMO R&T
!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Regular Screwdriver |
Adjustable Wrench |
Putty Knife |
Sealant |
Carpenters Level |
Wax Ring/Gasket |
Flexible Supply Tube |
Closet Bolts |
Hacksaw |
Tape Measure |
1REMOVE OLD TOILET
a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.Disconnect and remove supply line.
NOTE: If replacing valve, first shut off main water supply!
c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
Model 2891-BOULEVARD DUAL FLUSH ONE PIECE TOILET
|
FINISHED WALL |
|
|
|
|
|
|
29-3/4" |
|
|
|
|
7-1/2" |
(756 mm) |
|
|
14-1/2" |
|
(192 mm) |
|
|
|
|
|
|
|
|
(368 mm) |
|
|
|
|
|
|
|
3/4" |
mm) |
|
|
|
|
|
(19 |
C/L OF SEAT POST |
|
|
|
|
|
|
|
|
|
|
|
HOLES 5-1/2" |
|
|
14" |
|
|
(140mm) CENTERS |
|
|
|
|
|
|
|
|
(350 mm) |
|
|
18-1/2" |
|
|
|
|
|
(470 mm) |
|
|
|
3/8"-3 |
(86mm) |
|
SUPPLY |
|
30-7/8" |
|
(position 1 or |
|
|||
|
|
|
AS |
|
|
|
|
|
REQUIRED |
|
(784 mm) |
|
|
|
position 2) |
|
|
1/2"-3 |
(83mm) |
|
16-1/2" |
|
3-3/4" |
|
(140mm) |
(229mm) |
|||
|
|
|
(419 mm) |
9" |
(95mm) |
|
|
|
5-1/2" |
|
|
|
|
|
|
|
|
|
8-1/2" |
13-1/2" |
|
|
6" |
|
(217 mm) |
(345 mm) |
FINISHED |
|
14-1/4" (152mm) |
|
12" |
|
FLOOR |
(364 mm) |
|
|
(305 mm) |
|
|||
|
|
|
|
|
IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in). First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation. The second suggested position is next to the toilet. Between these two positions, the space for the supply between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.
Product names listed herein are trademarks of AS America, Inc. |
7301690-100 Rev. E |
© AS America, Inc. 2012 |
S A V E F O R F U T U R E U S E
3INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide into place 6" (152mm) apart and parallel to wall.
CLOSET
FLANGE
A
CLOSET
BOLTS
TIP: Place 2 pieces of masking tape on floor (as shown) to help with alignment in step 5.
4 |
5 |
SEALANT |
WAX RING |
|
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.
NUT
OPENING
WASHER
|
|
|
FLANGE |
|
CLOSET |
|
|
|
|
|
|
|
BOLT |
|
|
|
|
|
|
|
|
|
|
POSITION TOILET ON FLANGE
a.Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes.
b.Loosely install retainer washers and nuts.
6 INSTALL TOILET |
BOLT COVER |
a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
|
! CAUTION: DO NOT OVERTIGHTEN NUTS |
|
Back Side |
|
|
|
OR BASE MAY BE DAMAGED! |
|
|
b. |
Install bolt covers: |
|
Peel both protective films off |
|
|
and stick bolt cover to toilet. |
|||
|
1. |
Make sure that the bolt cover area on the toilet is clean and |
|
|
|
|
dry (see figure). Use a dry piece of cloth or soap and water |
|
|
|
|
if needed. |
|
|
|
2. |
Take plastic bolt cover and peel the brown protective film off |
|
|
|
|
on both ends. The adhesive part is now visible and ready to |
|
|
|
|
be placed on the toilet (see figure). |
BOLTS |
CLOSET FLANGE |
|
3. Gently place the bolt cover on the toilet area (see picture) and if |
|||
|
|
Front Side |
||
|
|
everything is aligned, push bolt cover firmly so it remains in place. |
|
BOLT COVER |
|
|
|
|
4.If not aligned, you can still take it off and put it back so it is aligned.
5. Repeat Step 3 for second bolt cover which is to be placed on opposite side of the toilet.
6.After 24 hours, the bolt cover adhesive has completely set off and if needed, you can remove/replace
as needed. The dual lock technology is now in place.
c. |
Smooth off the bead of sealant around base. Remove excess sealant. |
NUT |
|
|
CLOSET BOLT |
7 |
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. |
|
8a Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
|
|
|
RECOMMENDED |
|
METAL/COPPER |
METAL FLANGED |
METAL SPIRAL |
VINYL/BRAIDED |
|
FLARED TUBING |
TUBING |
TUBING |
CONNECTOR |
|
LOCK NUT |
LOCK NUT |
LOCK NUT |
LOCK NUT |
|
CONE |
EXISTING |
EXISTING |
COUPLING |
|
WASHER |
||||
WASHER |
CONE |
NUT |
||
COUPLING |
EXISTING |
WASHER |
|
|
|
|
|||
NUT |
COUPLING |
COUPLING |
|
|
|
NUT |
NUT |
|
|
WATER |
WATER |
WATER |
WATER |
|
SHUT-OFF |
SHUT-OFF |
SHUT-OFF |
SHUT-OFF |
These parts must be used as |
Use existing |
illustrated to insure water-tight |
coupling nut |
connection. Use of existing |
and washer. |
coupling nut may result in |
|
water leakage. Water supply |
|
tube or pipe must extend at |
|
least 1/2" inside threaded |
|
shank of valve (does not apply |
|
to flanged tubing). |
|
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
Use existing spiral cone |
Captive cone washers |
washer. Fluidmaster |
already included. No |
cone washer may not |
additional washers needed. |
seal completely on |
|
spiral type supply line. |
|
CAUTION: Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding.
8b
With correct washers in place (see Step 8a), tighten COUPLING NUT 1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
- 2 - |
7301690-100 Rev. E |