American Standard 6092, 6090, 6093, 6091, 2028.180 User Manual

...
0 (0)
American Standard 6092, 6090, 6093, 6091, 2028.180 User Manual

 

Installation

ACCESSORIES

Instructions

6028.230

6090

TOILET TISSUE HOLDER

2028.180

6091

18"TOWEL BAR

6028.244

6092

24"TOWEL BAR

6028.024

6093

GLASS SHELF

 

 

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

 

 

To ensure that your installation proceeds smoothly--please Certified to comply with ANSI A112.18.1

read instructions carefully before you begin.

.3&7

Recommended Tools

10'

Tape Measure

Regular Screwdriver

 

Drill

Phillips Screwdriver

Level

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF AND TOILET TISSUE HOLDER MOUNTING BRACKET INSTALLATION

The 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using the SCREWS (4) supplied.

If the 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER are to be installed on a tile or plaster wall the ANCHORS and SCREWS should be used.

Determine desired height and location (optional) for the accessory and mark a center line. Use the full size template supplied to mark hole locations for the mounting brackets. For the 24" TOWEL BAR and GLASS SHELF use 24” template. For 18” TOWEL BAR use 18” template. For the TOILET TISSUE HOLDER use the 7” template. If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (2).

For installations on drywall, use DRYWALL ANCHOR (3) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. Place MOUNTING BRACKET (1) over DRYWALL ANCHORS (3) and insert screws provided with #2 Phillips screwdriver. See illustration below. Secure MOUNTING BRACKETS (1) to wall with SCREWS (2).

For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (2) are used for securing MOUNTING BRACKET (1), then drill two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall.

Secure MOUNTING PLATES (1) to wall with SCREWS (2).

 

 

1a

 

INSTALL 18" TOWEL BAR, AND 24" TOWEL BAR

5a

CENTER

 

LEVEL

 

 

 

LINE

 

Place right ESCUTCHEON (5) onto MOUNTING BRACKET (1), and secure

6

1

 

with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.

 

 

Insert each end of TOWEL BAR (8) into the CRANKS (9).

Place LEFT ESCUTCHEON (5a) onto MOUNTING BRACKET (1a) and

9

8

 

secure with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.

 

5

 

 

 

 

6092

24"

6093

 

 

6

 

 

GLASS SHELF

24" TOWEL BAR

 

 

 

18"

 

 

 

 

CENTER LINE

 

7"

6091

 

 

FINISHED WALL

 

 

18" TOWEL BAR

CENTER LINE

 

 

(OPTIONAL TO

 

6090

 

 

 

 

 

FINISHED FLOOR)

9

TOILET TISSUE HOLDER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DRILL PILOT HOLE FOR

 

 

 

 

7

 

 

WOOD SCREW OR

 

 

 

 

 

 

1/4" DIA. HOLE FOR

 

 

 

 

 

 

ANCHOR

 

TEMPLATE

 

 

 

 

ANCHORS (FOR TILED WALLS)

 

 

 

 

 

DRYWALL ANCHORS

 

 

 

 

 

 

 

FINISHED WALL

1

CENTER

5, 5a

LINE

3, 4

2

 

 

1

4

DRILL PILOT HOLE FOR

 

WOOD SCREW (1) OR

 

3

1/4" DIA. HOLE FOR

6

ANCHOR (4)

SLOT

 

 

Loading...
+ 2 hidden pages