INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE
0641 BOULEVARD
0403 TROPIC PETITE
0404 TROPIC GRANDE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
Recommended Tools & Materials
|
|
Basin Wrench |
|
|
Tape |
|
|
Measure |
Putty Knife |
Adjustable Wrench |
|
Plumbers' Putty or |
|
|
|
|
|
|
Caulking |
|
Pipe Wrench |
Drill |
Hacksaw |
|
Saber Saw |
|
|
Tubing Cutter |
|
|
Phillips Screwdriver |
Regular Screwdriver |
|
|
Level Channel Lock Pliers
OBSERVE LOCAL PLUMBING AND BUILDING CODES
This lavatory can be installed 4 different ways. Please follow the instructions for your installation method.
1. PEDESTAL |
|
2. WALL-HUNG ON FURNITURE |
|
3. ABOVE COUNTER |
|
4. DROP-IN |
|
|
|||||
|
|
|
||||
|
|
|
|
* not recommended for 0404 |
|
* not recommended for 0404 |
S A V E F O R F U T U R E U S E
In the United States: |
In Canada: |
In Mexico: |
|
American Standard Brands |
AS Canada ULC |
Customer Service Manager |
|
P.O. Box 6820 |
2480 Stanfield Rd. |
AS Maquila, S.A. de C.V. |
|
Piscataway, New Jersey 08855 |
Mississauga, Ontario |
Via Morelos #330 |
|
Attention: Director of Consumer Affairs |
Canada L4Y 1S2 |
Col. Santa Clara |
|
For residents of the United States, warranty |
Toll Free: (800) 387-0369 |
Ecatepec 55540 Edo. Mexico |
|
|
|||
www.americanstandard.ca |
www.americanstandard.com/mx |
||
information may also be obtained by calling |
|||
the following toll free number: (800) 442-1902 |
|
|
|
www.americanstandard-us.com |
|
|
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c . © A S A m e r i c a , I n c . 2 0 0 9
7301354-100 Rev. B
1. Pedestal installation
1-A |
|
C/L of 2X6 |
|
|
|
Support |
|
Provide suitable reinforcement |
|
||
behind finished wall for lavatory |
|
||
mounting screws. |
* |
||
* Determine horizontal center line |
|||
|
|||
location of support from fixture. |
|
||
NOTE: If replacing an existing sink |
Finished |
||
be certain to shut off water supply |
|||
before removing old sink. |
Floor |
||
|
|||
1-B |
Top of Pedestal |
|
|
|
Approx. Bumper locations to |
||
|
raise the lavatory slab left side. |
For example only
Place lavatory and pedestal into installed position. Level and square the lavatory and pedestal assembly. Use one or more bumper cushions to level and cushion lavatory slab to pedestal.
1-C Mark lavatory and pedestal screw locations through the mounting holes.
1-D
Remove lavatory and pedestal from installed position. Drill pilot holes for lavatory and pedestal anchor screws or lag bolts.
Note: Some models are supplied with lag bolts, anchor screws, or steel hangers for lavatory installations only. Other models and all pedestals are not provided with mounting hardware. Various pedestal screw sizes and types are available to the installer at local hardware outlets.
1-F
Following manufacturer's instructions, install faucet and drain assembly (not included). Be certain to apply a bead of sealing putty on the underside of the drain (area "A") in order to ensure a watertight seal between the lavatory and drain. Remove excess putty after installing
drain on lavatory.
A |
1-G |
|
|
Return the fitted lavatory to the |
|
|
installed position. Connect trap to |
C |
|
drain assembly hand tight to check |
||
|
||
alignment. It may be necessary to |
B |
|
cut off part of the tailpiece (area |
|
|
"B") or part of the horizontal leg of |
|
|
the trap (area "C"). |
|
|
1-H |
|
|
Secure lavatory to wall as |
|
|
shown in 1E. Install washers |
|
|
and hand tighten nuts or lag |
|
|
bolts. Level and square the |
|
|
unit. Connect hot and cold |
|
|
supply lines to the shut-off |
|
|
valves. Tighten trap joints for |
Shut-Off |
|
watertight assembly. |
||
|
Valves |
1-I
Rear
View
Pedestal
Screws
Install pedestal screws. Securely tighten lavatory anchor nuts or lag bolts.
Note: Space constraints may dictate method of fastening pedestal to floor.
1-E |
ANCHOR SCREW INSTALLATION |
|
|
|
Install lavatory anchor screws |
|
leaving 1-7/8" threaded end |
|
exposed as illustrated. |
|
1-7/8" |
|
Lavatory |
|
Anchor |
|
Screw |
|
Nut |
|
Washer |
LAG BOLT INSTALLATION
Use lag bolts to secure lavatory as illustrated.
Lavatory
Steel
Hanger
Lag
Bolt
Washer
Lavatory
IMPORTANT: Final assembly of nut and washer or lag bolt method shown for reference only.
2 |
7301354-100 Rev. B |
|