American Standard 4077.014 Tank, 2067.014, 3110.016 Bowl, 2219.014 Elongated, 3225.016 User Manual

...
0 (0)
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90
°
, and slide
into place 6" (152 mm) apart and parallel to wall.
3
2
CLOSET FLANGE
CLOSET BOLTS
730945-100 Rev. C
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o du c t n a m e s li s t e d h e re in a r e t r ad em a r k s o f A me r i c a n S ta nd a r d I n c .
© A me r i c a n S t a nd a r d I n c . 20 0 7
!
NOTE: Pictures may not exactly define contour of china and components.
S A V E F O R F U T U R E U S E
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Skyline Champion®4 2-piece Toilets
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.
To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant
Hacksaw Wax Ring/Gasket Flexible Supply Tube 1/2" Deep Well Nut Driver or
Closet Bolts Tape Measure Carpenters Level Deep Well Socket Wrench
Recommended fitting type for back-to-back installations.
Depending upon your plumbing and venting conditions, the flow from
the Champion in a back-to-back installation may create a vacuum on
the system and draw water from the opposing bowl. The National
Standards Plumbing Code prohibits the use of a cross fitting for
drainage as throw over is possible. The code does approve a
directional "Y" style fitting with proper venting to direct the water
downward and away from the other toilet.
NOTE: BACK-TO-BACK INSTALLATION
MODEL A B C D
DIMENSIONS
2067.014 Elongated
Right Height™
2-pc Toilet
2112.014 Round Front
Normal Height
2-pc Toilet
18-1/ 2"
470mm
16-1/ 2"
419mm
30-3/ 8"
772mm
34-3/ 8"
873mm
16-1/ 2"
419mm
15-1/ 4"
387mm
28-3/ 8"
721mm
33-1/ 8"
841mm
2219.014 Elongated
Normal Height
2-pc Toilet
18-1/ 2"
470mm
15-1/ 4"
387mm
30-3/ 8"
772mm
33-1/ 8"
841mm
ROUGHING-IN DIMENSIONS: Right Height™ Elongated Two Piece Toilet
Normal Height Round Front Two Piece Toilet
Normal Height Elongated Two Piece Toilet
FIN ISH ED WAL L
19m m ± 6m m
(1 ± 1 /4)
B
FIN ISH ED
FLO OR
305 mm
(12 )
C
C/L OF OU TLE T
83m m
(3- 1/4 )
235 mm
(9- 1/4 )
A
C/L OF SE AT POST HO LES
140 mm (5- 1/2 CENTER S)
362 mm
(14 -1/ 4)
264mm
(10-3/8)
16m m
(5/ 8)
D
498 mm
(19 -5/ 8)
SUP PLY
AS
REQ 'D
254 mm
(10 )
152 mm
(6)
254 mm
(10 )
356 mm
(14 )
*
2067.014 Right Height™ Elongated: 3225.016 Bowl and 4077.014 Tank
2112.014 Round Front: 3110.016 Bowl and 4077.014 Tank
2219.014 Elongated: 3121.016 Bowl and 4077.014 Tank
730945-100 Rev. C
WAX RING
SEALANT
54
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
- 2 -
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
MANIFOLD INSIDE WATERWAY - DO NOT REMOVE
6
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers.
(If necessary, cut bolt height to size before installing caps.)
c. Smooth off the bead of sealant around base.
Remove excess sealant.
!
CLOSET BOLT
NUT
WASHER
BOLT CAP
9a
Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts
required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing coupling
nut may result in water leakage.
Water supply tube or pipe must
extend at least 1/2" inside threaded
shank of valve (does not apply to
flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral cone
washer. Fluidmaster
cone washer may not
seal completely on
spiral type supply line.
Captive cone
washers already
included. No
additional washers
needed.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER
INSTALL TANK
a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank
onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening,
and tank mounting bolts go through mounting holes. Secure with metal
washer/nuts.
b. With tank parallel to wall, alternately tighten hex nuts until tank is snugged down
evenly against bowl surface.
Recommended tool: Deep socket tool included in tank kit.
!
CAUTION:
7
8
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
DO NOT SPIN BOLTS WITH SCREWDRIVER
RUBBER
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
WASHER/NUT
CLOSE T FLANG E
Loading...
+ 3 hidden pages