American Standard 2071S User Manual

Size:
391.72 Kb
Download

Installation

Instructions

T H E

MONOBLOCK

2071

LAVATORY FAUCET

 

C O L L E C T I O N

2071S

by

WITH CROSS HANDLE

 

 

Thank you for selecting American-Standard...thebenchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M

M 9 6 8 2 9 0 A

TOOLS REQUIRED

Channel Locks

Adjustable Wrench

Plumbers' Putty or Caulking

Phillips Screwdriver

CARE INSTRUCTIONS:

To keep your new faucet looking new, please follow these simple care instructions:

DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth.

DO NOT:

Do not use any abrasive cleaners, cloths, or paper towels.

Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps.

Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is

1

 

 

 

 

INSTALL FAUCET

 

CAUTION

Turn off water at

 

 

main supply.

 

 

 

 

 

 

 

Remove as much surface dirt and film using clear water and soft cotton cloth (as described above).

Use any of the following to remove tough surface film and build-up:

Mild liquid detergents

Clear ammonia free liquid glass cleaners

Non-acidic,non-abrasivegentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions.

Non-abrasiveliquid polishers

Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth.

Failure to follow these care instructions may damage the Faucet's finish.

INSTALLATION OPTIONS; Faucet may be installed with ESCUTCHEON PLATE (1) or for center hole only with ESCUTCHEON RING (2).

INSTALLATION with ESCUTCHEON PLATE (1)

No sealant is required unless mounting surface is uneven for 3-hole

7

(4" centers) installation with ESCUTCHEON PLATE (1). Place ESCUTCHEON

PLATE (1) over mounting holes on lavatory sink or mounting surface.

 

Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through hole in ESCUTCHEON PLATE (1). Seat ESCUTCHEON PLATE (1) boss into groove in Faucet base.

From below, install MOUNTING GASKET with RETAINING WASHER (5) and Nut (6) onto

STUD (4). Pull Faucet to front of sink, so STUD BOSS

(4) rests against sink hole. Before final tightening, align Faucet and ESCUTCHEON (1) so they are centered on mounting surface. Tighten NUT (6)

to secure Faucet

GROOVE IN

Insert LIFT ROD (7). ESCUTCHEON RING BASE

GROOVE IN

FAUCET BASE

BOSS

1

4

2

INSTALLATION with ESCUTCHEON RING (2)

For single hole installation use ESCUTCHEON RING (2). Install SEAL WASHER (6) into groove in ESCUTCHEON RING (2) base and place over over mounting hole in lavatory sink or mounting surface.

Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through hole in ESCUTCHEON RING (2). Seat ESCUTCHEON RING (2) boss into groove in Faucet base.

From below, install MOUNTING GASKET with RETAINING WASHER (5) and Nut (6) onto STUD (4). Pull Faucet to front of sink, so STUD

(4) rests against sink hole. Before final tightening, align Faucet and ESCUTCHEON (1) so they are centered on mounting surface. Tighten NUT (6) to secure Faucet

Insert LIFT ROD (7).

6

LAVATORY SINK

OR MOUNTING

SURFACE

3

5

6

2 INSTALLPOP-UPDRAIN

Push Tail piece (11) down into Trap (C) (threaded end up).

Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side up) onto Drain Body (10).

Apply a bead of Putty (D) to underside of Flange (2).

Feed Drain Body (10) up through Sink (A) and thread the Flange (2) or (2A) fully onto Drain Body (10).

Tighten Locknut (5) firmly, keeping the pivot rod hole pointed towards the back of the sink.

Assemble Pivot Rod (9) as shown in Figure-3A.Notice the position of the Concave Washer (G).

Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot Nut (F).

Push TAILPIECE INSERT (12) into TAILPIECE (11) and push TAILPIECE up and thread tightly into DRAIN BODY (10).

Position Extension Rod (7) onto Pop-UpRod (E) and tighten Thumbscrew (6).

Remove one end of Clip (8) from Pivot Rod (9) by squeezing ends together while sliding.

Insert Pivot Rod (9) or (9A) into second or third hole in Extension Rod (7) and reassemble Clip (8).

Drop Stopper (1) into Drain Body (10).

Adjust stopper height by repositioning Extension Rod (7) and tightening Thumbscrew (6).

3 WATER SUPPLY CONNECTIONS

Note: FLEXIBLE HOSES (1, 2) on FAUCET (3) are(17-1/2")in length from base of faucet. If longer supply length is required installer must purchase adapters and additional supplies to complete connections.

Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking .

Connection on FLEXIBLE HOSES (1, 2) are 3/8" compression. Connect LEFT SUPPLY (1) to Hot shut off valve and RIGHT SUPPLY (2) to Cold shut off valve.

Use adjustable wrenches to tighten connections. Do not over tighten.

1

 

 

 

2

 

 

 

A

 

D

 

 

E

 

 

 

 

3

 

6

 

4

 

7

7

 

 

 

5

F

 

8

 

 

 

10

 

 

 

12

 

 

9

 

C

 

11

 

 

1-1/4"

 

 

 

 

 

 

9

 

 

O-RING

G

 

F

 

 

FIGURE-3A:

3

(17-1/2")

1

COLD 2

3/8" compression

HOT

SHUT OFF

VALVE

 

M 9 6 8 2 9 0 A

4 TEST INSTALLED FAUCET AND CHECK FOR LEAKS

With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3).

Operate HANDLE (1) to flush water lines thoroughly.

Replace AERATOR (3).

4a CHECK DRAIN CONNECTIONS

Operate LIFT ROD (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in lavatory. If necessary adjust stopper height by repositioning LIFT ROD (4) and tightening Thumbscrew (6).

Release DRAIN STOPPER (5) and check all drain connections and "P" trap for leaks.Tighten if necessary.

1

3

4

6

5

"P" TRAP

COLD

2

HOT

5 ADJUST HOT LIMIT STOP

By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (5) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP (5).

Remove INDEX BUTTON (1), HANDLE SCREW (2) and pull off HANDLE (3).

Turn CARTRIDGE STEM (4) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (5). Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (5). Pull upward and rotate counterclockwise one number to limit hot water temperature. Use ARROW (6) on CARTRIDGE (7) and NUMBERS (8) on HOT LIMIT STOP (5) for indication.

Replace HANDLE (3), HANDLE SCREW (2) and INDEX BUTTON (1).

1

HOTTER

(Smaller Numbers)

0 1 3 5 7 9 11 13 15

1

2

3

5

1

513

 

 

 

 

9

11

 

 

 

 

57

3

 

 

3

 

 

1

1

 

 

 

 

0

 

 

 

 

 

5

 

 

 

 

 

 

1

4

6

8

5

7

FLAT BLADE SCREWDRIVER 6

1

5

13

 

 

 

1197531

5

4

1

5

13

 

 

 

1197531

 

 

 

COLDER

(Larger Numbers)

0 1 3 5 7 9 11 13 15

5

M 9 6 8 2 9 0 A

M962242-YYY0A

KNOB & ROD

M962237-0070A

INDEX BUTTON

A918657-0070A

 

 

HANDLE SCREW

 

T H E

 

 

C O L L E C T I O N

 

 

by

M962236-YYY0A

 

 

HANDLE

 

MONOBLOCK

 

 

 

LAVATORY FAUCET

M914423-YYY0A

WITH CROSS HANDLE

 

 

METAL RING

MODEL NUMBER

A912706-0070A

 

 

O-RING

 

2071

 

 

918633-0070A

 

2071S

CARTRIDGE SCREWS

 

 

A923611-0070A

Replace the "YYY" with

appropriate finish code

HOT LIMIT STOP

CHROME

002

 

 

SATIN

295

A954400-0070A

 

 

CARTRIDGE KIT

 

 

 

072574-0070A

066116-YYY0A

 

DRAIN STOPPER

 

EXTENSION ROD

 

 

 

 

066117-YYY0A

 

 

FLANGE KIT

 

 

FLANGE

066070-YYY0A

 

AERATOR

GASKET

 

953450-YYY0A

 

 

 

COMPLETE

 

M962238-YYY0A

DRAIN ASSEMBLY

WASHER

 

ESCUTCHEON KIT

070847-0070A

 

(THREE HOLE)

 

CLIP

LOCKNUT

 

 

 

 

M962239-YYY0A

 

 

ESCUTCHEON KIT

 

 

(SINGLE HOLE)

 

051049-0070A

066118-0070A

M961711-0070A

MOUNTING KIT

TAILPIECE INSERT

 

PIVOT ROD

 

 

 

 

070532-0040A

3

 

TAILPIECE

 

 

HOT LINE FOR HELP

For toll-freeinformation and answers to your questions, call:1-800442-1902

Weekdays 8:00 a.m. to 8:00 p.m. EST

IN CANADA 1-800-387-0369(TORONTO1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.

© American Standard Inc. 2003

M 9 6 8 2 9 0 A