American Standard 1660.300 User Manual

Size:
163.67 Kb
Download

 

Installation

 

Instructions

SHOWER SYSTEMS

THREE WAY:

1660.300

 

1660.430

TWO WAY OR THREE WAY

1660.431

TWO WAY:

IN-WALLDIVERTER1660.200 1660.440 1660.441

Thank you for selecting American-Standard...thebenchmark of fine quality for over 100 years.

MAX

Certified to comply with ANSI A112.18.1M

To ensure that your installation proceeds smoothly--please

 

 

read these instructions carefully before you begin.

 

50321B

 

 

 

 

 

 

ROUGHING-INDIMENSIONS

 

CAUTION: DO NOT SEAL ANY OUTLETS. DIVERTER

 

NOTE: NO CONCEALED PIPING FURNISHED

 

 

2-9/16

 

CANNOT BE USED AS A STOP VALVE.

 

TWO WAY

 

 

 

 

BODY

 

 

 

 

 

 

 

 

2-1/4

 

 

 

3-1/8

 

DISK

 

 

 

 

O-RINGS

 

 

 

 

DISK

UPPER

 

FINISHED

THREE WAY

O-RING

 

DISK

 

WALL

BODY

 

 

 

 

SHAFT

 

 

 

 

 

 

 

 

SPRING

 

1-5/8

 

 

 

 

ALL CONNECTIONS 1/2" NPT

 

 

 

SHAFT

CAP

 

 

 

O-RING

 

 

 

PLASTER

 

 

 

 

 

 

 

 

GUARD

LOWER

DISK

MAX

WASHER

CLIP

WASHER

CAP

SEAL

ESCUTCHEON

ESCUTCHEON

 

 

 

 

 

 

 

STEM

NUT

HANDLE

 

 

 

 

 

 

HANDLE

 

 

 

ADAPTER

 

 

 

 

 

HANDLE

(1660.430/.440

 

 

 

 

 

 

 

 

 

DECORATOR

 

 

 

 

RING

HANDLE

(1660.200/.300)

 

 

 

 

SCREW CAP

 

 

 

INDEX

 

 

 

 

 

 

 

 

 

 

BUTTON

HANDLE

 

 

 

 

 

 

 

 

 

 

(1660.431/.441)

 

 

 

HANDLE

HANDLE

VANDAL-RESISTANT

HANDLE

HANDLE

SKIRT

INDEX CAP

 

SCREW

 

ADAPTOR

SCREW

 

VANDAL-RESISTANT

 

 

HANDLE SCREW

P r i n t e d i n G e r m a n y

1

ROUGHING-IN

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

 

 

Turn off hot and cold water supplies before beginning.

 

 

 

 

 

 

 

 

 

 

 

 

 

See Roughing-inDrawing on reverse side. The port with the BATH TUB picture is the high flow.

The DIVERTER can be installed with the inlet rotated in any position.

Supply connections are 1/2" NPT connections.

For proper positioning the finished wall must be within side of PLASTER GUARD.

Connect water to valve. The reverse side of the body is marked with arrows. CAUTION: Do not solder near the VALVE. Damage to the SEAL may occur.

Do not seal any outlets. The DIVERTER cannot be used as a stop valve.

For support use pipe braces secured to wooden braces.

2 TEST DIVERTER

DIVERTER

Check that the DIVERTER operates correctly and does not leak. To do this, screw off the PLASTER GUARD, turn around, and

insert using the fluted pin into the fluting on the DIVERTER SPINDLE and use as a diverter knob. Screw the PLASTER GUARD back on. Have the wall tiled only with the PLASTER GUARD screwed on.

PLASTER

GUARD

MAX

DIVERTER

SPINDLE

3

INSTALL TRIM

 

(For 1660.200/.300, handles are

ESCUTCHEON

 

purchased separately.)

NUT STEM

When finished tiling wall, remove

PLASTER GUARD.

Place ESCUTCHEON on ESCUTCHEON

HOLDER and screw HOLDER onto VALVE.

For 1660.430/.440 Series:

Push HANDLE ADAPTER onto STEM.

Make sure arrow is up.

ESCUTCHEON

Assemble HANDLE and DECORATOR RING onto HANDLE ADAPTER. Secure with HANDLE SCREW.

 

Snap on HANDLE CAP.

 

 

 

 

 

 

 

 

Check for leaks.

 

 

 

 

 

 

 

 

To operate, turn the HANDLE clockwise or counter clockwise.

HANDLE

 

 

 

 

 

SKIRT

 

 

 

 

 

 

For 1660.431/.441 Series:

Assemble HANDLE SKIRT then HANDLE LEVER to ESCUTCHEON NUT STEM. Secure with HANDLE SCREW.

Push on INDEX BUTTON or screw on VANDAL RESISTANT INDEX CAP. Check for leaks.

To operate, turn the HANDLE clockwise or counter clockwise.

HANDLE

ADAPTER HANDLE

DECORATOR

RING

HANDLE SCREW

CAP

INDEX

BUTTON

VANDAL-RESISTANTHANDLE INDEX CAP SCREW

VANDAL-RESISTANT

HANDLE SCREW

4 SERVICE

To Replace O-Rings:

Turn off water supply.

For 1660.430/.440 Series:

Use a small screw driver to remove HANDLE CAP.

Remove HANDLE SCREW, DECORATOR RING, HANDLE and ADAPTER.

Unscrew ESCUTCHEON HOLDER and remove HOLDER and ESCUTCHEON.

Unscrew CAP and remove STEM, SPRING and SEALS.

Remove old DIVERTER elements and install new parts.

Replace remaining parts in reverse order.

For 1660.431/.441 Series:

DISK

O-RING

DISK

O-RINGUPPER DISK

SHAFT

SPRING SHAFT

O-RING

CAP

LOWER

DISK

WASHER

WASHER

 

 

Remove INDEX BUTTON (or unscrew VANDAL RESISTANT INDEX CAP).

 

Unscrew ESCUTCHEON HOLDER and remove HOLDER

 

 

 

 

 

Remove HANDLE SCREW, LEVER HANDLE and HANDLE SKIRT.

 

and ESCUTCHEON.

 

 

 

 

 

 

 

Unscrew CAP and remove STEM, SPRING and SEALS.

 

 

 

 

 

 

 

 

 

 

Remove old DIVERTER elements and install new parts.

 

 

HOTLINE FOR HELP

 

 

 

 

 

 

 

 

 

 

Replace remaining parts in reverse order.

 

 

 

 

 

 

For toll-freeinformation and answers to your questions, call:

 

 

 

 

 

 

 

 

1 (800) 442-1902

 

 

 

 

 

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

 

 

 

 

 

IN CANADA 1-800-387-0369(TORONTO1-416-536-5609)

© A m e r i c a n S t a n d a r d I n c . 1 9 9 5

 

 

 

 

 

50321B