American Standard 1660.13 User Manual

Size:
242.54 Kb
Download

Installation

Instructions

LUXURY SHOWER

1660.130

EXTENDER BODY SPRAYS

1660.140

Thank you for selecting American-Standard...thebenchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

1660.130 1660.140

Certified to comply with ANSI A112.18.1

M968617 Rev. 1. 2

Recommended Tools

Flat Blade Screwdriver

2-1/4"DIA.

Teflon Tape

Electric Drill

(57mm) Hole Saw

 

 

 

ROUGHING-INDIMENSIONS

ALL CONNECTIONS 1/2" NPT

75mm

(3")

74mm D. (2-15/16")

1660.130 Multifunction

1660.140 Multifunction

Round Body Spray

Square Body Spray

26mm

(75.6-82.6mm)

 

(1")

2-15/16"-3-1/4"

 

 

12mm

 

 

(1/2")

 

15°

 

 

 

54mm D.

 

 

(2-1/8")

35mm

 

 

(1-3/8")

 

57mm D.

 

 

(2-1/4")

1/2" NPT

FINISHED WALL

HOLE SIZE

 

(63.6-70.6mm)

 

 

2-1/2"-2-3/4"

 

1

 

 

Turn off hot and cold water

INSTALL SUPPLY PIPING

CAUTION

supplies before beginning.

 

Provide a “Installation Hole” 2-1/8"-2-3/8"DIA.,(54-60mm)and3-1/4",(83mm) deep.Note: The“Installation Hole” must be clear to allow body spray clearance.

Install the ELBOW (1) on a support within the wall at the *dimension shown. Secure with two M5 SCREWS(2) (not provided).

 

 

 

 

 

82.6mm

 

 

 

 

 

(3-1/4")

 

 

 

 

83mm

 

 

 

 

(3

-1/4")

 

54-60

 

 

1

(2-

mm

 

 

1/8" -

 

 

 

 

2-3/8"

DIA.)

 

2

 

 

 

 

 

54-60mm

 

 

 

 

 

(2-1/8"-2-3/8"DIA.)

 

 

 

 

 

1

 

 

 

 

 

“Installation Hole”

 

 

 

 

{“Installation Hole”

 

 

 

 

2

*63.6-70.6mm

 

 

 

 

 

(2-1/2"-2-3/4")

 

 

 

 

 

FINISHED WALL

 

 

 

 

 

*75.6-82.6mm

 

 

 

 

 

(2-15/16"-3-1/4")

 

 

 

 

 

WALL SUPPORT

2 INSTALL PLASTER GUARD

Make sure the O-RING(3) is installed on the PLASTER GUARD(1).

Install the PLASTER GUARD (1) into ELBOW(2).Note: The finished wall must be between the Min. & Max. lines on the PLASTER GUARD(1).

Complete all tiling and wall work. When walls are finished remove PLASTER GUARD (1).

 

 

FINISHED WALL

 

 

 

1

3

 

2

MAX.

2

3

(LINE MARK)

 

 

 

INSTALL

 

 

 

REMOVE

 

MINIMUM

 

 

 

 

 

1

(LINE MARK)

 

 

 

 

 

 

 

M968617 Rev. 1. 2

3 INSTALL BODY SPRAY

Remove the PLASTER GUARD (1) if not already removed.

Make sure the O-RING(2) and FLANGE GASKET(6) are installed on the BODY SPRAY(3). Thread BODY SPRAY(3) into the ELBOW(4).

Tighten BODY SPRAY (3) using WRENCH(5) supplied until flush against finished wall and FLANGE GASKET(6) is compressed. Turn on water supply and test installed BODY SPRAY(3) for leaks and proper operation.

 

 

 

2

6

2

4

4

 

 

 

 

 

 

3

1

3

 

 

6

 

 

 

 

 

 

5

 

 

 

FINISHED WALL

5

4 INSTALL ESCUTCHEON

Align ribs on back of ESCUTCHEON (1, 2), with slots in BODY SPRAY(3). Push ESCUTCHEON(1, 2) against BODY SPRAY(3) until ESCUTCHEON(1, 2) snaps into place.

Turn on water supply and test installed BODY SPRAY (3) for leaks and proper operation.

FINISHED WALL

ALIGNMENT RIBS ON

BACK OF ESCUTCHEON

SLOTS

3

ALIGNMENT RIBS ON

 

BACK OF ESCUTCHEON

1

2

2

1

5 CARE:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

M968617 Rev. 1. 2