American Standard 1340M Series User Manual

Size:
185.4 Kb
Download

Installation

Instructions

METERING FAUCET

1340 SERIES

1340M SERIES

SINGLE TAP PUSH BUTTON FAUCET

1340 SERIES FOR COLD AND TEMPERED SUPPLIES

1340M SERIES INCLUDES BELOW DECK MIXING VALVE WITH STRAINER

PUSH

Certified to comply with ANSI A112.18.1M

U.S. PATENT NOS.

Thank you for selecting American-Standard...thebenchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.

WARNING: SUPPLY INLET MUST BE FILTERED WITH A 60 MESH SCREEN.

 

USE AMERICAN STANDARD MIXING VALVE WITH STRAINER OR COMMERCIAL 60 MESH STRAINER.

0 1 2 6 9 2 D

 

BODY

SET SCREWS

 

AERATOR

HANDLE

 

 

 

KEY

 

 

 

SPRING

 

GASKET

 

 

 

RETAINING

 

 

RING

 

 

LEVER

 

ESCUTCHEON KIT

 

 

(OPTIONAL)

VALVE

 

 

CARTRIDGE

 

DECK

 

 

WASHER,

HANDLE

 

RETAINER

 

BRASS

 

 

 

LOCK-RING

 

 

AND SCREWS

 

 

RISER TUBE

 

 

(NOT INCLUDED)

 

 

1340 SERIES

 

 

SUPPLY

 

 

NUT

 

MIXING

 

 

STRAINER

 

 

VALVE

FILTER

 

ASSEMBLY

 

SCREEN

 

 

 

 

DUCK

 

 

BILL 1340M SERIES

 

 

CHECKS

 

1 ASSEMBLING ESCUTCHEON KIT (OPTIONAL)

CAUTION

Turn off hot and cold water supplies before beginning.

Peel off paper backing from PADS and stick both PADS to underside of ESCUTCHEON about 1/4" from ends.

Peel off paper backing from WASHER and stick

WASHER into circular groove of SUPPORT PLATE.

PAD

Place SUPPORT PLATE in center

WASHER

 

of ESCUTCHEON with WASHER visible.

 

Apply a bead of PUTTY around

SUPPORT

PLATE

the inside of ESCUTCHEON edge.

 

Turn ESCUTCHEON over and

PAD

 

center it with SUPPORT

 

 

PLATE over center hole

PUTTY

ESCUTCHEON

of sink deck.

 

 

 

2

ASSEMBLING MOUNTING KIT

LOCK RING

 

 

 

 

 

Thread (3) SCREWS into LOCK RING.

SCREWS should extend half-waythru RING.

SCREWS

3 MOUNTING FITTING

Install faucet through the ESCUTCHEON being sure the rubber GASKET is between the FAUCET and the ESCUTCHEON.

Install brass WASHER and turn LOCK-RINGonto SHANK.

Tighten (3) SCREWS in the LOCK-RINGto secure fitting.

FOR 1340 SERIES ONLY

Warning; 60 MESH STRAINER required for supply water.

Install RISER TUBE (not included) and tighten SUPPLY NUT.

Connect RISER TUBE to COLD or TEMPERED water supply.

FOR 1340M SERIES

STRAINER

MIXING

VALVE

Connect FLEXIBLE FAUCET SUPPLIES (1/2" faucet cone on one end, 3/8" compression on the other) to the MIXING

VALVE INLETS and the

 

hot/cold wall stops.

 

The FLEXIBLE FAUCET

 

SUPPLIES are NOT

 

included. Turn on WALL

 

STOPS and check

 

for leaks.

HOT

With WALL STOPS open and water flowing, adjust MIXING VALVE to temper water.

MIXING

VALVE

INLETS

MIXING

VALVE

ADJUSTMENT

FLEXIBLE

FAUCET

SUPPLIES

WALL

COLD

STOPS

MIXING

VALVE

HOTTER

COLDER

4 TO OPERATE

7 sec.

 

 

 

PUSH

 

-

Start

 

40 sec.

+

 

 

Lever

Retaining

 

 

Ring

Stop

10 sec.

 

Automatic

minimum

 

 

Lift off retaining

 

 

ring then slide

 

 

out lever

 

 

horizontally.

 

Press down to start.

Cycle time is factory set but can

 

be changed as shown.

5 TO SERVICE

TO remove HANDLE use a 3/32" ALLEN WRENCH to loosen three set screws in the HANDLE as shown in Figure A.

Remove VALVE CARTRIDGE for cleaning or replacement, see in Figure B.

Reassemble in reverse order, Figures C & D.

 

VALVE

 

CARTRIDGE

 

 

 

 

TIGHTEN VALVE

HANDLE

 

CARTRIDGE

REMOVE

REPLACE

3/32" ALLEN WRENCH

Figure A

Figure B

Figure C

 

TIGHTEN

SET SCREWS

Figure D

6 SPRAY INSTALLATION/REMOVAL

7 ROUGHING-INDIMENSIONS

48mm (1-55/64)

 

111mm

 

 

 

(4-3/8)

 

 

 

 

45mm

 

 

 

(1-3/4DIA.)

53mm

 

 

 

(2)

 

 

 

30°

 

 

21mm

 

Use included key to install SPRAY into spout end.

 

(53/64 DIA.)

 

 

 

1/2"-14

 

 

 

NPSM

 

HOTLINE FOR HELP

25mm

THREAD

 

For toll-freeinformation and answers to your questions, call:

(1" MAX)

 

 

1 (800) 442-1902

 

 

 

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time

 

90mm

 

IN CANADA 1-800-387-0369(TORONTO1-905-306-1093)

 

(3-9/16)

 

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

All dimensions are approximate and for reference only.

 

 

 

C A m e r i c a n S t a n d a r d I n c . 1 9 9 6

 

 

0 1 2 6 9 2 D