American Standard 1340.865 User Manual

Size:
719.62 Kb
Download

 

Installation

METERING

Instructions

1340.725

SPREAD LAVATORY

1340.825

FAUCETS

1340.855

 

 

1340.865

Thank you for selecting American-Standard...thebenchmark of fine quality for over 100 years.

1340.725

 

 

1340.825

1340.855

1340.865

To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M

TOOLS REQUIRED

 

Channel Locks

Adjustable Wrench

Plumbers' Putty or Caulking

2.5mm Hex Wrench

 

 

 

Turn off hot and cold water

 

SPOUT ASSEMBLY

CAUTION

supplies before beginning.

 

 

 

 

 

Install RING WASHER (1) into SPOUT (2) recess. Check

that O-RING(3) on end of SPOUT SHANK (4) is in place. Insert SPOUT SHANK (4) into center hole on mounting surface.

Assemble RUBBER WASHER (5) and BRASS WASHER (6) and LOCKNUT (7) onto SPOUT SHANK (4). Align SPOUT ASSEMBLY. From underside of ledge, tighten LOCKNUT (7) to secure SPOUT ASSEMBLY to mounting surface.

SPOUT

ASSEMBLY

SPOUT RECESS

2

 

1

 

 

 

4

3

MOUNTING

 

 

 

SURFACE

5

6

7

PREPARE TUBE AND TEE ASSEMBLY

Remove COUPLING NUT (1) and FERRULE (2) from each VALVE (3) and slide onto TUBING (4).

1

2

4

1

2

8"

 

 

MOUNTING

 

 

SURFACE

 

 

3

 

REMOVE HANDLE AND

3

ACTUATOR ASSEMBLY

2

 

Remove HANDLE (1) by

1

removing INDEX BUTTON (2) and SET SCREW (3) with a 2.5mm hex wrench.

Pull off HANDLE (1).

Remove ACTUATOR

ASSEMBLY (4).

Remove WASHER (5).

NOTE; Washer (5) may remain inside of Actuator Assembly.

REMOVE REPLACE

4

5

VALVE ASSEMBLY (1340.825; 1340.855; 1340.865)

Install LOCKNUTS (1), METAL WASHERS (3) and RUBBER WASHERS (2) onto valve shanks.

Push TUBING (14) ends into VALVE (4) side outlets. Insert VALVES (4) into mounting holes from underside of ledge.

Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING(7) is properly seated on SHANK (6). Push COUPLING (8) into TEE (5) and

attach to SPOUT SHANK (6) and tighten.

Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1).

Place RUBBER RING (10) into ESCUTCHEONS (9) and thread onto valves until snug against internal stop.

 

Tighten LOCKNUT (1) to secure VALVE (4) position.

MOUNTING

 

SURFACE

 

Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4)

 

 

 

 

 

and tighten COUPLING NUT (13) firmly.

 

Place WASHER (16) on top of VALVE ASSEMBLY (4).

15

10

11

9

16

10

Thread VALVE ACTUATORS (15) onto VALVES (4) and torque VALVE

 

 

 

 

ACTUATOR 12-15ft. lbs,(12-20Nm).

 

 

 

7

Connect water supply to VALVES (4) with 1/2" IPS FLEXIBLE SUPPLIES or

 

 

 

 

12

 

 

3/8" O.D. BULL-NOSERISERS. Use adjustable wrench to tighten connections.

4

13

6

Do not over tighten. Be careful not to kink copper supply when bending. Use

 

 

16

tubing cutter to cut to proper length.

 

 

 

HOT

 

 

 

 

 

 

 

 

10

9

 

 

12

 

 

 

14

 

 

 

 

 

 

 

 

 

5/16'' MIN.

4

11

MOUNTING

5

 

 

 

 

SURFACE

8

4

 

 

 

 

 

3

2

 

13

COLD

 

1

 

1/2" IPS FLEXIBLE SUPPLIES or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3/8" O.D. BULL-NOSERISERS

 

 

 

 

 

COUPLING NUT

 

VALVE ASSEMBLY (1340.725)

For Cold or Tempered Water Supply

Valve assembly is same as two handle lavatory faucets. See above instructions for assembly, (1340.725 Single Valve Faucet) is for Cold or Tempered water only.

15

9

10

9

MOUNTING

11

10

 

SURFACE

 

 

5/16'' MIN.

4

11

MOUNTING

7

 

 

 

 

SURFACE

16

 

 

 

 

 

 

2

 

6

 

 

 

 

 

12

 

3

1

 

5

 

 

 

 

 

 

 

 

 

8

4

 

13

COLD OR

14 TEMPERED

WATER

1/2" IPS FLEXIBLE SUPPLIES or 3/8" O.D. BULL-NOSERISER

COUPLING NUT

INSTALL HANDLES

Remove INDEX BUTTON (1; 2) and loosen SET SCREW (3) with a 2.5mm hex wrench.

Install HANDLES (4) onto VALVE STEM (5).

Tighten SET SCREWS (3) with 2.5mm Hex Wrench.

Replace INDEX BUTTONS. Red (1) in Left HANDLE (4) Blue (2) in Right HANDLE (4).

1

4

3

3

4

2.5mm

HEX WRENCH

5

2

TEST INSTALLED FITTING

 

Turn on water supplies and check connections for leaks.

PRESS HANDLE

 

 

DOWN TO OPERATE

 

 

 

Remove AERATOR (1) with KEY (2) supplied.

 

 

 

Operate HOT and COLD HANDLES by pressing down on HANDLES.

Both Hot and Cold handles are set for approximately 8 second operating cycles.

Replace AERATOR (1).

1

2

TO ADJUST CYCLE TIME

Remove HANDLE (1) by removing INDEX BUTTON (2) and SET SCREW (3) with a 2.5mm hex wrench.

Pull off HANDLE (1).

To increase cycle time, turn the gray PLASTIC ADJUSTING KNOB (4) clockwise.

To decrease cycle time, turn the gray PLASTIC

ADJUSTING KNOB (4) counter-clockwise.

Replace SET SCREW (3), INDEX BUTTON (2) and HANDLE (1). Test faucet for proper operation and cycle time.

2

3

 

 

 

1

 

2.5mm HEX WRENCH

TO DECREASE

TO INCREASE

 

CYCLE TIME

CYCLE TIME

 

ROTATE

ROTATE

 

COUNTER-

CLOCKWISE

CLOCKWISE

 

4

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

SERVICE

Remove HANDLE (1). Refer to Step 4 for handle removal.

Remove ACTUATOR ASSEMBLY (2).

Remove WASHER (3). Pull out VALVE ASSEMBLY (4) and

FILTER SCREEN (5).

Inspect that VALVE ASSEMBLY (4), FILTER SCREEN (5) and VALVE SEAT (6) are clean and free from debris. VALVE ASSEMBLY (3) and FILTER SCREEN (5) can be cleaned with soap and water.

Replace FILTER SCREEN (5) and VALVE ASSEMBLY (4). Place WASHER (3) on top of VALVE ASSEMBLY (4). Thread VALVE ACTUATOR (2) onto faucet. Torque VALVE ACTUATOR (2)

to 12-15ft. lbs(15-20Nm).

Replace HANDLE (1).

1

REMOVE

REPLACE

2

3

4

5

6

 

 

 

METERING

 

 

 

Center Set Faucets

 

 

 

PRODUCT NUMBERS

M962390-YYYOA

 

 

1340.825

HANDEL KIT

 

 

1340.725

M962391-0070A

 

 

 

 

5" GN 1340.855

INDEX KIT

 

 

M952200-YYY0A

M962392-0070A

6" GN 1340.865

VALVE KIT

 

 

ACTUATOR UNIT

 

 

 

 

 

 

M962399-YYY0A

M913860-0070A

 

 

SPOUT KIT

WASHER

 

 

 

M952210-0070A

 

 

 

VALVE

 

 

M962393-YYY0A

M952220-0070A

 

 

1.56 GPM AERATOR

 

 

 

FILTER SCREEN

 

 

 

M962398-YYY0A

 

A911836-0070A

 

ESCUTCHEON KIT

 

SEAL WASHER

 

 

 

030253-0070A

 

051213-0070A

 

SPOUT MTG. KIT

 

 

 

 

MOUNTING KIT

 

 

 

 

 

028679-0070A

M962400-0070A

 

 

TUBE & TEE

TUBE & TEE ASSEMBLY

 

 

ASSEMBLY

(FOR 1340.725)

 

 

033757-0070A

 

 

 

TEE MTG. KIT

 

024220-0070A

 

 

 

SUPPLY NUT

 

 

 

 

012078-0070A

 

 

VALVE COUPLING KIT

 

 

 

M962406-YYY0A

 

 

 

6" SPOUT KIT

 

 

Replace the "YYY" with

 

 

appropriate finish code

 

 

CHROME

002

 

M962394-YYY0A

 

 

M962394-YYY0A

AERATOR

 

 

AERATOR

 

HOT LINE FOR HELP

M962405-YYY0A

5" SPOUT KIT

For toll-freeinformation and answers to your questions, call:

 

 

1 (800) 442-1902

 

 

Weekdays 8:00 a.m. to 8:00 p.m. EST

 

 

IN CANADA 1-800-387-0369

(TORONTO 1-905-306-1093)

 

 

Weekdays 8:00 a.m. to 7:00 p.m. EST

 

 

Product names listed herein are trademarks of American Standard Inc .

 

 

© American Standard Inc . 2005