American Standard 1340.225 User Manual

Size:
688.81 Kb
Download

 

Installation

 

 

 

METERING

Instructions

 

 

 

1340.225

 

 

 

Center Set Faucets

1340.255

 

 

 

 

 

 

 

 

1340.265

 

 

 

Thank you for selecting American-Standard...the

 

 

 

benchmark of fine quality for over 100 years.

1340.225

1340.255

1340.265

To ensure that your installation proceeds

smoothly--pleaseread these instructions carefully

Certified to comply with ANSI A112.18.1

before you begin.

TOOLS REQUIRED

 

Channel Locks

Adjustable Wrench

Plumbers' Putty or Caulking

2.5mm Hex Wrench

INSTALL FAUCET

CAUTION

Turn off hot and cold water supplies before beginning.

Apply a bead of PUTTY along the edge of the underside of the FAUCET (1).

Insert faucet SHANKS through holes of SINK or MOUNTING SURFACE.

Install GASKET (2), FRICTION WASHER (3), DEEP WASHER (4) and LOCK NUT (5). onto SHANKS (6).

Tighten LOCK NUTS (5) firmly to secure FAUCET (1).

1

SHANK

PUTTY

SINK OR

MOUNTING

SURFACE

2

3

4

MAKE WATER SUPPLY CONNECTIONS

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSERISERS MUST BE PURCHASED SEPARATELY.

Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (1) or 3/8" O.D. BULL-NOSERISERS (2).

Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.

1

COUPLING NUT

2

FERRULE

5

TEST INSTALLED FITTING

Turn on water supplies and check connections for leaks.

Remove AERATOR (1) with KEY (2) supplied.

Operate HOT and COLD HANDLES by pressing down on HANDLES. Both Hot and Cold handles are set for approximately 8 second operating cycles.

PRESS HANDLE

Replace AERATOR (1). DOWN TO OPERATE

1

2

WATER SUPPLIES

TO ADJUST CYCLE TIME

Remove HANDLE (1) by removing INDEX BUTTON (2) and SET SCREW (3) with a 2.5mm hex wrench.

Pull off HANDLE (1).

To increase cycle time, turn the gray PLASTIC ADJUSTING NUT (4) clockwise.

To decrease cycle time, turn the gray PLASTIC ADJUSTING NUT (4) counter-clockwise.

Replace SET SCREW (3), INDEX BUTTON (2) and HANDLE (1). Test faucet for proper operation and cycle time.

3

2

1

2.5mm HEX WRENCH

TO DECREASE CYCLE TIME

ROTATE COUNTER-CLOCKWISE

TO INCREASE CYCLE TIME

ROTATE CLOCKWISE

4

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

SERVICE

Remove HANDLE (1). Refer to Step 4 for handle removal.

Remove ACTUATOR ASSEMBLY (2).

Remove WASHER (3). Pull out VALVE ASSEMBLY (4) and FILTER SCREEN (5).

Inspect that VALVE ASSEMBLY (4), FILTER SCREEN (5) and VALVE SEAT (6) are clean and free from debris. VALVE ASSEMBLY (3) and FILTER SCREEN (5) can be cleaned with soap and water.

Replace FILTER SCREEN (5) and VALVE ASSEMBLY (4). Place WASHER (3) on top of VALVE ASSEMBLY (4). Thread VALVE ACTUATOR (2) onto faucet. Torque VALVE ACTUATOR (2)

to 12-15ft. lbs(15-20Nm).

Replace HANDLE (1).

1

REMOVE

REPLACE

2

3

4

5

CONVERT RIGID SPOUT TO SWIVEL SPOUT

(1340.255; 1340.265)

Unthread SPOUT NUT (1) and remove SPOUT (2)

Remove SPOUT CLIP (3) and O-RINGS(4).

Replace RUBBER RING (5) with separate

PLASTIC RING (6) supplied with faucet.

Replace SPOUT CLIP (3) and O-RINGS(4).

Reassemble SPOUT (2) TO BODY.

2

1

REMOVE 5

RUBBER RING

3

4

INSTALL 6

PLASTIC RING

 

 

METERING

 

 

Center Set Faucets

 

 

PRODUCT NUMBERS

 

M962390-YYYOA

1340.225

 

HANDEL KIT

5" GN 1340.255

 

 

 

M962391-0070A

6" GN 1340.265

 

INDEX KIT

 

 

M952200-YYY0A

 

Replace the "YYY" with

ACTUATOR UNIT

M962392-0070A

 

VALVE KIT

appropriate finish code

 

 

CHROME

002

M913860-0070A

WASHER

M952210-0070A

VALVE

M952220-0070A

FILTER SCREEN

M962393-YYY0A

1.56 GPM AERATOR

M962397-0070A

MOUNTING KIT

024220-0070A

SUPPLY NUT

 

M962394-YYY0A

M962394-YYY0A

M962396-YYY0A

AERATOR

AERATOR

6" SPOUT KIT

 

 

 

M962395-YYY0A

 

 

5" SPOUT KIT

 

HOT LINE FOR HELP

For toll-freeinformation and answers to your questions, call: 1 (800)442-1902

Weekdays 8:00 a.m. to 8:00 p.m. EST

IN CANADA 1-800-387-0369(TORONTO1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc . © American Standard Inc . 2005

012087-0070A

051214-0070A

SPOUT SEAL KIT

SWIVEL & FIXED

 

SPOUT RINGS