American Standard 0621.001 STUDIO User Manual
CARE AND MAINTENANCE
ABOVE COUNTER SINK
FOR USE WITH: 0621.001 STUDIO
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED FAUCET*: 2064.101 ONE lavatory faucet
*Log on to
RECOMMENDED TOOLS AND MATERIALS
Channel Lock Pliers
Plumber’s Putty or Caulking
OBSERVE LOCAL PLUMBING AND BUILDING CODES
1a Countertop Installation:
Using the template provided, locate the position of the sink on the countertop. Provide proper clearance under the countertop for the faucet supply lines, drain assembly and the structural parts of the cabinet. NOTE: If replacing an existing sink be certain to shut off water supply before removing old sink.
1b Mounting on Studio 22" Vanity:
Assemble vanity as per instructions.
2Drill a clearance hole inside the perimeter line of the template for countertop installation.
Cut opening around the perimeter of the template.
3Mount the faucet and drain assembly (not included) on the sink following the manufacturer’s instructions. Be certain to apply a bead of sealing putty on the underside of the drain (Part “A”) in order to ensure a watertight seal between the sink and drain. Remove excess putty after installing drain on sink.
•Place the sink temporarily into the template
•Check for alignment and clearance
•Mark the sink and countertop in several places as a guide for the installation location.
4b Vanity Installation:
•Place the sink temporarily on the vanity to check for alignment and clearance
•The sink should be centered left to right on the vanity with the front edge of the sink even with the front of the vanity
After checking fit and alignment, turn sink upside down and apply a generous portion of silicone adhesive around the under side of the rim near the edge. Place sink in position. Wipe off excess adhesive.
S A V E F O R F U T U R E U S E
P r o d u c t n a m e s l i s t e d
h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 8
Connect supply line to faucet (finger tight) and carefully bend tubes to engage with the supply
Connect trap to drain assembly hand tight to check alignment. It may be necessary to cut off part of the tailpiece (area “B”) or part of the horizontal leg of the trap (area “C”). Secure joints for watertight assembly.
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
If inspection of this AS America, Inc. (”American Standard”) plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof of purchase will be
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation.
This limited warranty is void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.
American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal or installation. IN NO EVENT WILL AMERICAN STANDARD BE LIABLE FOR THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION MATERIALS, INCLUDING BUT NOT LIMITED TO, TILES, MARBLE ETC. American Standard will not be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this limited warranty. This limited warranty does not cover any liability for consequential or incidental damages, all of which are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including those of merchantability or fitness for an intended purpose. (Some states or provinces do not allow the exclusion or limitation of implied limited warranties, so this exclusion may not apply to you.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this limited warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard, Inc.,
Customer Service Manager
P.O. Box 6820
2480 Stanfield Rd.,
Ideal Standard, S.A. de C.V.
Piscataway, New Jersey 08855
Via Morelos #330
Attention: Director of Consumer Affairs
Canada L4Y 1S2
Col. Santa Clara
For residents of the United States, warranty
Toll Free: (800)
Ecatepec 55540 Edo. Mexico
information may also be obtained by calling the
following toll free number: (800)