American Standard 0.18 User Manual

Size:
214.68 Kb
Download

 

Installation

ACCESSORIES

Instructions

6028.230

6090

TOILET TISSUE HOLDER

6028.180

6091

18"TOWEL BAR

6028.244

6092

24"TOWEL BAR

6028.024

6093

GLASS SHELF

Thank you for selecting American-Standard...thebenchmark

of fine quality for over 100 years.

 

To ensure that your installation proceeds smoothly--pleaseCertified to comply with ANSI A112.18.1

read instructions carefully before you begin.

M968860 REV . 1 . 1

 

 

Recommended Tools

10'

Tape Measure

Regular Screwdriver

 

Drill

Phillips Screwdriver

Level

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

1

18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF AND TOILET TISSUE HOLDER

MOUNTING BRACKET INSTALLATION

The 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using the SCREWS (4) supplied.

If the 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER are to be installed on a tile or plaster wall the ANCHORS and SCREWS should be used.

Determine desired height and location (optional) for the accessory and mark a center line. Use the full size template supplied to mark hole locations for the mounting brackets. For the 24" TOWEL BAR and GLASS SHELF use 24” template. For 18” TOWEL BAR use 18” template. For the TOILET TISSUE HOLDER use the 7” template. If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (2).

For installations on drywall, use DRYWALL ANCHOR (3) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. Place MOUNTING BRACKET (1) over DRYWALL ANCHORS (3) and insert screws provided with #2 Phillips screwdriver. See illustration below. Secure MOUNTING BRACKETS (1) to wall with SCREWS (2).

For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (2) are used for securing MOUNTING BRACKET (1), then drill two 1/4" diameter holes a minimum of1-1/4"deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall.

Secure MOUNTING PLATES (1) to wall with SCREWS (2).

2

 

1a

 

INSTALL 18" TOWEL BAR, AND 24" TOWEL BAR

5a

CENTER

 

LEVEL

 

 

 

LINE

 

Place right ESCUTCHEON (5) onto MOUNTING BRACKET (1), and secure

6

1

 

with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.

 

 

Insert each end of TOWEL BAR (8) into the CRANKS (9).

Place LEFT ESCUTCHEON (5a) onto MOUNTING BRACKET (1a) and

9

8

 

secure with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.

 

5

 

 

 

 

6092

24"

6093

 

 

6

 

 

GLASS SHELF

24" TOWEL BAR

 

 

 

18"

 

 

 

 

CENTER LINE

 

7"

6091

 

 

FINISHED WALL

 

 

18" TOWEL BAR

CENTER LINE

 

 

(OPTIONAL TO

 

6090

 

 

 

 

 

FINISHED FLOOR)

9

TOILET TISSUE HOLDER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DRILL PILOT HOLE FOR

 

 

 

 

7

 

 

WOOD SCREW OR

 

 

 

 

 

 

1/4" DIA. HOLE FOR

 

 

 

 

 

 

ANCHOR

 

TEMPLATE

 

 

 

 

ANCHORS (FOR TILED WALLS)

 

 

 

 

 

DRYWALL ANCHORS

 

 

 

 

 

 

 

 

FINISHED WALL

1

CENTER

3

5 5a

LINE

4

2

 

 

1

 

 

 

4

DRILL PILOT HOLE FOR

 

 

WOOD SCREW (1) OR

 

 

3

1/4" DIA. HOLE FOR

 

6

ANCHOR (4)

 

SLOT

 

 

 

3 INSTALL GLASS SHELF

Place ESCUTCHEON (1,1a) onto installed MOUNTING

5

6

BRACKETS (2) and secure with SET SCREWS (3) using

2.5mm HEX WRENCH (4) supplied.

8

Remove SCREW (5) and top WASHER (6) from SHELF

 

RISER (7).

 

Install GLASS SHELF (8) onto SHELF RISERS (7).

 

Secure GLASS SHELF (8) with SCREWS (5) and

 

 

 

5

WASHERS (6).

 

 

 

 

 

 

 

 

5

 

7

 

6

 

 

6

 

 

 

 

 

 

1

3

2

FINISHED WALL

1 1a

 

 

 

 

 

 

 

 

7

 

 

 

2

2

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

3

 

 

 

 

1a

 

 

 

 

 

 

 

 

6092

24"

6093

 

3

 

 

GLASS SHELF

 

24" TOWEL BAR

 

 

18"

 

 

 

 

 

 

6091

 

 

 

 

 

6090

18" TOWEL BAR

CENTER LINE

 

 

 

CENTER

 

 

 

FINISHED WALL

 

7"

 

 

 

 

LINE

TOILET TISSUE HOLDER

 

 

 

 

 

 

 

DRILL PILOT HOLE FOR

 

 

 

 

 

 

WOOD SCREW OR

 

 

 

 

 

 

1/4" DIA. HOLE FOR

 

 

 

 

 

 

ANCHOR

 

 

 

 

 

 

ANCHORS (FOR TILED WALLS)

 

 

 

 

 

 

DRYWALL ANCHORS

 

 

 

 

4 INSTALL TOILET TISSUE HOLDER

 

 

 

 

 

Place ESCUTCHEON with TISSUE PAPER ROD ATTACHED (1) onto LEFT MOUNTING BRACKET (2) and secure with SET SCREW (3) using 2.5mm HEX WRENCH (4) supplied.

Attach ESCUTCHEON (1A) to RIGHT MOUNTING BRACKET (2A) and secure with set screw (3) using 2.5mm HEX WRENCH (4) supplied.

Swing TISSUE PAPER ROD (5) onto LATCH (6) at the tip of the

RIGHT ESCUTCHEON (1A) to complete assembly.

2

FINISHED WALL

 

2A

1 1A

1

5

 

1A

2

 

 

3

4

3

7”

6

2

CENTER LINE

OPTIONAL TO

FINISHED FLOOR

M968860 REV . 1 . 1