American Power Conversion 7500-10000 VA User Manual

Size:
991.17 Kb
Download

User Manual

English

APC Smart-UPS® RT

7500/10000 VA 200-240VAC 6U

Tower/Rack Mount

Uninterruptible Power Supply

990-1216B02/2004

Introduction

The APC Smart-UPSRT is ahigh-performance,uninterruptible power system (UPS), designed to prevent blackouts, brownouts, sags and surges from reaching your computers, servers, and other sensitive electronic equipment.

1: INSTALLATION

Attention: Read the safety information sheet before installation.

Unpacking

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly. Check the package contents:

UPS (with batteries disconnected)

Two front bezels

Literature kit containing:

Software

Smart-UPSUser Manuals CD

XLI model only: Six output power cords

Serial cable

Product documentation, safety and warranty information

SNMP/Web Card User Manual

Removing the Batteries

The unit is heavy. To lighten the unit, remove the batteries. Refer to the unpacking instructions on the carton in which the unit is shipped.

Placement

Attention: The UPS is heavy. Select a location sturdy enough to handle the weight.

Do not operate the UPS in excessive dust or in temperature and humidity outside the specified limits.

Ensure the air vents on the front and rear of the UPS are not blocked.

Refer to the APC web site, www.apc.com for details.

1

Hardwiring

Attention: Wiring must be performed by a qualified electrician.

1.Install a utility circuit breaker in accordance with local electrical codes (see tables below) for input wiring only.

2.Switch the UPS input circuit breaker (see A) and utility circuit breakers OFF.

3.Remove the access panel (see B).

4.Remove circular knockouts.

5.Run wires through access panel to terminal blocks. Wire to ground block first. Adhere to all national and local electrical codes. (See tables and graphics.)

6.Use appropriate glands to achieve strain-reliefon the hardwired input and output power cables.

XLT, XLJ, AND XLTW MODELS

Input Connection

 

 

 

 

 

 

Output Connection (optional)

 

 

Wire to L1, L2, and .

 

 

 

 

Wire to L1A, L2A, and

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

System

 

Wiring

 

 

Voltage

Current

External Input

 

Wire Size

 

 

 

 

 

 

 

 

Full Load

Circuit Breaker

 

(typical)

 

 

 

 

 

 

 

 

(Nominal)

(typical)

 

 

 

SURT7500XLJ,

 

Input & Output

 

200/208/220V

40 amps

50 amps / 2-polefor

 

#8AWG/

SURT7500XLT,

 

 

 

 

 

 

XLTW- 38 amps

Input Wiring Only

 

10mm2

SURT7500XLTW

 

 

 

 

 

 

 

 

 

 

 

 

SURT10000XLJ,

 

Input & Output

 

200/208/220V

54 amps

70 amps / 2-polefor

 

#6AWG/

SURT10000XLT,

 

 

 

 

 

 

XLTW-50amps

Input Wiring only

 

16mm2

SURT10000XLTW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

XLI MODELS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Connections

 

 

 

 

 

 

Output Connection (optional)

 

 

 

 

 

 

 

 

 

 

 

 

Single-Phase:Wire to L1, N, and .

 

 

Wire to L1A, N1, and

.

 

 

 

Three-Phase:Wire to L1, L2, L3, N, and .

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

System

 

Wiring

Number

 

Voltage

Current

 

External Input

 

Wire Size

 

 

 

 

of

 

 

Full Load

 

Circuit Breaker

 

(typical)

 

 

 

 

Phases

 

 

(Nominal)

 

(typical)

 

 

SURT7500XLI

 

Input

1

 

 

220/230/240V

38 amps

 

50 amps / 2-pole

 

10mm2

 

 

 

 

 

 

 

 

 

 

 

 

 

Input

3+

 

 

380/400/415V

14 amps / phase when

50 amps / 4-pole

 

10mm2

 

 

 

 

Neutral

 

 

online, 38 amps on L1

 

 

 

 

 

 

 

 

 

 

 

 

in bypass

 

 

 

 

 

 

 

Output

1

 

 

220/230/240V

38 amps

 

(not required)

 

10mm2

 

 

 

 

 

 

 

 

 

 

 

 

SURT10000XLI

 

Input

1

 

 

220/230/240V

50 amps

 

63 amps / 2-pole

 

16mm2

 

 

Input

3+

 

 

380/400/415V

18 amps / phase when

63 amps / 4-pole

 

16mm2

 

 

 

 

Neutral

 

 

online, 50 amps on L1

 

 

 

 

 

 

 

 

 

 

 

 

in bypass

 

 

 

 

 

 

 

Output

1

 

 

220/230/240V

50 amps

 

(not required)

 

16mm2

2

7.XLI model only: Forthree-phaseinput, set the Input Phase Selector switch (seeC) to ‘3’. Forsingle-phaseinput, leave switch in default position of ‘1’.

XLT/XLJ/XLTW MODELS

OUTPUT

L1A

L2A

INPUT

L1

L2

A B

XLI MODEL

A

8.Switch the circuit breakers ON.

9.Check line voltages.

10.Replace the access panel.

3

OUTPUT

L1A

N1

INPUT

L1

L2

L3

N

C

B

Installing and Connecting the Batteries and Attaching the Front Bezel

 

 

 

 

 

 

4

CONNECTINGPOWER ANDEQUIPMENT TO THEUPS

1.Hardwire the UPS (see Hardwiring).

2.Connect equipment to the UPS (cables not included for XLT/XLJ/XLTW models).

3.Turn on all connected equipment. To use the UPS as a master on/off switch, be sure that all connected equipment is switched ON.

4.Press the button on the front panel to power up the UPS.

The battery charges to 90% capacity during the first three hours of normal operation. Do not expect full battery run capability during this initial charge period.

5.Configure the Web/SNMP management card (optional).

OPTIONS

Refer to the APC web site, www.apc.com for available accessories.

External Battery Pack SURT192XLBP

Rail Kit SURTRK2

Isolation Transformer

Service Bypass Panel

CIRCUITBREAKERS

Input Circuit Breaker The UPS is protected from extreme overloads when in ON position.

7500/10000 VA The breaker must be on for the UPS to operate.

XLI/XLJ/XLT/XLTW

Output Circuit Breaker 7500/10000 VA XLJ/XLT/XLTW

L6-20

L6-30

250V 20A

250V 30A

Output Circuit Breaker

7500/10000 VA XLI

IEC 320-C13

IEC 320-C19

10A for each

16A for each

receptacle

receptacle

5

BASICCONNECTORS

 

Power management software and interface kits can be used with the

Serial Port

UPS.

Use only interface kits supplied or approved by APC.

 

 

 

Connect the UPS to the network.

Ethernet Port

(Located on Web/SNMP card.)

 

 

 

 

The optional Emergency Power Off (EPO) feature allows connected

 

loads to be immediately de-energizedfrom a remote location, without

EPO Terminal

switching to battery operation (see EPO Option).

 

 

 

 

The UPS features a transient voltage surge-suppression(TVSS) screw

 

for connecting the ground lead on surge suppression devices such as

TVSS Screw

telephone and network line protectors.

 

When connecting grounding cable, disconnect the unit from the utility

 

power outlet.

 

Optional external battery packs provide extended runtime during

External Battery Pack

power outages. These units support up to 10 external battery packs.

See the APC website, www.apc.com/products for the information on

Connectors

the external battery pack, SURT192XLBP.

6

2:OPERATION

FRONTDISPLAYPANEL

Indicator

Description

 

 

Online

The UPS is drawing utility power and performing double conversion to supply

 

power to connected equipment (see Troubleshooting).

 

 

On Battery

The UPS is supplying battery power to the connected equipment.

 

 

Bypass

The UPS is in bypass mode, sending utility power directly to connected equipment.

 

Bypass mode operation is the result of an internal UPS fault, an overload condition

 

or a user initiated command either through an accessory or the manual bypass

 

switch. Battery operation is not available while the UPS is in bypass mode (see

 

Troubleshooting).

Fault

The UPS detects an internal fault (see Troubleshooting).

 

 

Overload

The connected loads are drawing more power than the UPS power rating (see

 

Troubleshooting).

 

 

Replace

The battery is disconnected or must be replaced (see Troubleshooting).

Battery

 

 

 

 

 

Feature

Function

 

 

Power On

Press this button to turn on the UPS. (Read on for additional capabilities.)

 

 

Power Off

Press this button to turn off the UPS.

 

 

 

7

Feature

Function

 

 

 

 

 

 

Normal /Bypass

Manually switch connected equipment to bypass mode, so that utility power is

 

sent directly to connected equipment. Battery operation is not available while

 

the UPS is in bypass mode. (See Troubleshooting.)

 

Cold Start

This is not a normal condition.

 

 

 

 

Supply immediate battery power to the UPS and connected equipment (see

 

Troubleshooting). Press and hold the

button to power up the UPS and

 

connected equipment. The UPS will emit two beeps. During the second beep,

 

release the button.

 

 

 

 

Self-Test

Automatic: The UPS performs aself-testautomatically when turned on, and

 

every two weeks thereafter (by default). During the self-test,the UPS briefly

 

operates the connected equipment on battery.

 

 

Manual: Press and hold the

button for a few seconds to initiate the self-

 

test.

 

 

 

 

Diagnostic Utility

The UPS has a diagnostic feature that displays the utility voltage. Plug the UPS

Voltage

into the normal utility power.

 

 

 

 

The UPS starts a self-testas part of this procedure. Theself-testdoes not

 

affect the voltage display.

 

 

 

 

Press and hold the

button to view the utility voltage bar graph display.

 

After a few seconds the five-LED,Battery Charge

display on the right of

 

the front panel shows the utility input voltage.

 

 

Refer to the figure at left for the voltage reading (values are not listed on the

 

UPS).

 

 

 

 

 

The display indicates the voltage is between the displayed value on the list and

 

the next higher value.

 

 

 

 

 

 

 

 

 

 

On Battery Operation

The UPS switches to battery operation automatically if the utility power fails. While running on battery, an alarm beeps four times every 30 seconds.

Press the button to silence this alarm. If the utility power does not return, the UPS continues to supply power to the connected equipment until the battery is fully discharged.

When two minutes of runtime remain the UPS emits a continuous beep. If PowerChute or the Web/SNMP card is not being used, files must be manually saved and the computer must be properly shut down before the UPS fully discharges the battery.

The UPS battery life differs based on usage and environment. Refer to www.apc.com/products for on battery runtimes.

8