American Power Conversion 5000 VA User Manual

Size:
486.02 Kb
Download

User Manual

English

APC Smart-UPS® RT

3000/5000 VA 200-240VAC

Tower/Rack Mount 3U

Uninterruptible Power Supply

990-269002/2006

Introduction

The APC Smart-UPS®RT is ahigh-performance,uninterruptible power supply (UPS) that provides protection for electronic equipment from utility power blackouts, brownouts, sags and surges. The UPS filters small utility line fluctuations and isolates electronic equipment from large disturbances by internally disconnecting from utility line power. The UPS provides continuous power from the internal battery until utility power returns to safe levels or the battery is fully discharged.

INSTALLATION

Read the Safety Guide before installing the UPS.

Unpacking

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly.

Check the package contents:

UPS (with battery modules disconnected)

Front bezel

Literature kit containing:

Product documentation

Smart-UPSRT User Manuals CD

Warranty Information

Specifications

XLT/XLI/XLTW models:Software CD

Serial cable

3000 VA XLI models: three output power cords, two input power cords

3000 VA models: conversion faceplate for accommodating a Network Management Card

5000 VA XLI models: six output power cords, Network Management Card documentation

TEMPERATURE

 

This unit is intended for indoor use only.

OPERATING

32° to 104° F (0° to 40° C)

Select a location sturdy enough to

STORAGE

5° to 113° F (-15°to 45° C) charge the UPS

handle the weight.

 

battery every six months

Do not operate the UPS where there is

MAXIMUM

 

excessive dust or the temperature and

ELEVATION

 

humidity are outside the specified limits.

OPERATING

10,000 ft (3,000 m)

Ensure that the air vents on the front

STORAGE

50,000 ft (15,240 m)

and rear of the UPS are not blocked.

 

 

 

 

 

HUMIDITY

0 to 95% relative humidity

 

 

 

 

 

 

 

 

WEIGHT

 

 

 

 

UPS

120 lbs (55 kg)

 

 

 

UPS WITH

140 lbs (64 kg)

 

 

 

PACKAGING

 

 

 

 

 

1

 

 

 

Wiring and Connecting the UPS

5000 VA XLI MODELSONLY: HARDWIRINGINSTRUCTIONS

Wiring must be performed by a qualified electrician.

Install a high magnetic 30/32 A utility circuit breaker.

Adhere to all national and local electrical codes.

Use #10 AWG gauge (5 mm2) wire.

1.Switch the utility circuit breaker OFF.

2.Remove the input access panel.

3.Remove circular knockout.

4.Run #10 AWG gauge (5 mm2) wire through the access panel, and connect the wires to the terminal block (Green: Ground, Brown: Hot, Blue: Neutral). Use an appropriate strain relief (not included).

5.Switch the utility circuit breaker ON.

6.Check line voltages.

7.Replace the access panel.

2

CONNECTING THEBATTERY MODULES ANDATTACHING THEFRONTBEZEL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

BASICCONNECTORS

 

 

 

 

 

 

 

The serial connector is to be used for interfacing with APC PowerChute

 

 

 

 

 

 

 

software and terminal emulation software.

serial com

Use only cables approved by APC.

 

 

 

 

 

 

 

Any other interface cable will be incompatible with the UPS

 

 

 

 

 

 

 

connector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Manual bypass enables the user to manually put connected equipment into

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bypass mode.

normal bypass

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Emergency Power Off terminal allows the user to connect the UPS to the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

central EPO system.

EPO terminal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The UPS features a transient voltage surge-suppression(TVSS) screw for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connecting the ground lead on surge suppression devices such as telephone

TVSS screw

and network line protectors.

When connecting grounding cable, disconnect the unit from the utility

 

 

 

 

 

 

 

 

 

 

 

 

 

 

power outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Optional external battery packs provide extended run time during power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

outages. These units support up to ten external battery packs.

external battery

See the APC Web site, www.apc.com for the information on the external

pack connector

battery pack, SURT192XLBP.

 

 

5000 VA

 

XLI models

 

 

 

 

 

 

 

 

 

output circuit breakers

3000/5000VA XLJ/XLT/XLTW models

output circuit breakers

4

CONNECTINGEQUIPMENT ANDPOWER TO THEUPS

1.Connect equipment to the UPS (cables not included for XLJ/XLT/XLTW models).

2.Avoid using extension cords.

3000 VA XLJ/XLT/XLI/XLTW and 5000 VA XLJ/XLT/XLTW models: Using a power cord, plug the UPS into a two-pole, three-wire, grounded receptacle only.

5000 VA XLJ models: To draw full 5000 VA from the UPS have a qualified electrician cut off the input plug and hardwire the UPS to the appropriate power panel.

3.Turn on all connected equipment. To use the UPS as a master ON/OFF switch, ensure all connected equipment is switched ON. The equipment will not be powered until the UPS is turned on.

4.To power up the UPS press the button on the front panel.

The UPS battery charges when it is connected to utility power. The battery charges to 90% capacity during the first three hours of normal operation. Do not expect full battery run capability during this initial charge period.

5.For additional computer system security, install PowerChute® Server Smart-UPSmonitoring software.

OPTIONS

Refer to the APC Web site, www.apc.com for available accessories.

External Battery Pack SURT192XLBP

Rail Kit SURTRK2

Isolation Transformer

Service Bypass Panel

5

OPERATION

Load

SMART-UPS RT FRONTDISPLAY

Battery Charge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicator

 

Description

 

 

 

 

 

 

Online

 

The Online LED illuminates when the UPS is drawing utility power and performing

 

 

 

 

 

 

double conversion to supply power to connected equipment.

 

 

 

 

 

 

On Battery

 

The UPS is supplying battery power to the connected equipment.

 

 

 

 

 

Bypass

 

The Bypass LED illuminates indicating that the UPS is in bypass mode. Utility

 

 

 

 

 

 

power is sent directly to connected equipment during bypass mode operation.

 

 

 

 

 

 

 

 

 

 

 

 

Bypass mode operation is the result of an internal UPS fault, an overload condition

 

 

 

 

 

 

or a user initiated command either through an accessory or the manual bypass

 

 

 

 

 

 

 

 

 

 

 

 

switch. Battery operation is not available while the UPS is in bypass mode. Refer to

 

 

 

 

 

 

Troubleshooting in this manual.

 

 

 

 

Fault

 

The UPS detects an internal fault.

 

 

 

 

 

 

Refer to Troubleshooting in this manual.

 

 

 

 

 

 

 

 

 

 

Overload

 

An overload condition exists. See Troubleshooting.

 

 

 

 

Replace

 

The battery is disconnected or must be replaced. See Troubleshooting.

Battery

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Feature

 

Function

 

 

 

Power On

 

Press this button to turn on the UPS. (See below for additional capabilities.)

 

 

 

 

 

 

 

 

 

 

 

Power Off

 

Press this button to turn off the UPS.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

Feature

Function

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cold Start

When there is no utility power and the UPS is off, press and hold the

 

 

button to

 

 

 

 

 

 

 

 

power up the UPS and connected equipment.

 

 

 

 

 

 

 

The UPS will emit two beeps. During the second beep, release the button.

 

 

 

 

 

 

 

 

 

 

 

 

Self-Test

Automatic: The UPS performs aself-testautomatically when turned on, and every

 

 

 

two weeks thereafter (by default). During the self-test,the UPS briefly operates the

 

 

 

connected equipment on battery.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Manual: Press and hold the

 

button for a few seconds to initiate the self-test.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Diagnostic Utility Voltage

The UPS has a diagnostic feature that displays the utility voltage. Plug

 

 

 

 

 

the UPS into the normal utility power.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The UPS starts a self-testas part of this procedure. Theself-test

 

 

 

 

 

does not affect the voltage display.

 

 

 

 

 

 

 

 

 

Press and hold the

 

button to view the utility voltage bar graph

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

display. The five-LED,Battery Charge

 

display on the right of the

 

 

 

 

 

 

 

 

 

 

 

front panel shows the utility input voltage.

 

 

 

 

 

 

 

 

 

Refer to the figure at left for the voltage reading (values are not listed

 

 

 

 

 

on the UPS).

 

 

 

 

 

 

 

 

 

 

 

 

The display indicates the voltage is between the displayed value on the

 

 

 

 

 

list and the next higher value.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

USERCONFIGURABLEITEMS

NOTE: SETTINGS ARE MADE THROUGH SUPPLIEDPOWERCHUTE SOFTWARE, OPTIONALSMARTSLOT ACCESSORY CARDS, ORTERMINALMODE.

FUNCTION

FACTORY

USERSELECTABLE

DESCRIPTION

DEFAULT

CHOICES

 

 

Automatic Self-Test

On start-upand

On start-upand every 7

Set the interval at which the

 

every 14 days,

days thereafter

UPS will execute a self-test.

 

thereafter

On start-upand every 14

 

 

 

days thereafter

 

 

 

On start-uponly

 

 

 

No self-test

 

 

 

 

 

Date of Last Battery

Manufacture date

Date of

Reset this date when you replace

Replacement

 

battery replacement

the battery modules.

 

 

 

 

Minimum Run time

0 seconds

0 to 3600 s of run time

Specify the minimum run time

Before Return from

 

 

following a low battery

Shutdown

 

 

shutdown, before powering

 

 

 

connected equipment.

Audible Alarm

ON

ON, OFF

Enable or disable all alarms

Setting

 

 

permanently.

 

 

 

 

Simple Shutdown

90 seconds

0 to 1800 s

Set the interval between the time

Delay

 

 

when the UPS receives a simple

 

 

 

shutdown command and the

 

 

 

actual shutdown.

 

 

 

 

Simple Low Run

150 seconds

0 to 1800 s

Change the warning interval

Time Warning

 

 

default to a higher setting if the

 

 

 

operating system requires a

 

 

 

longer interval for shutdown.

 

 

 

The low battery warning beeps

 

 

 

are continuous when 150

 

 

 

seconds of run time remain.

 

 

 

 

High Bypass Point

 

Output Voltage Setting

Maximum voltage that the UPS

 

255 VAC

200 VAC:

will pass to connected

 

 

210 - 280 VAC

equipment during internal

 

 

bypass operation.

 

 

208 VAC:

 

 

 

 

 

220 - 280 VAC

 

 

 

220 VAC:

 

 

 

235 - 280 VAC

 

 

 

230 VAC:

 

 

 

245 - 280 VAC

 

 

 

240 VAC:

 

 

 

255 - 280 VAC

 

 

 

 

 

8