American Power Conversion 240 VAC User Manual

Size:
403.91 Kb
Download

User Manual

English

APC Smart-UPS® RT – UXI/UXICH

8000/10000 VA 220/230/240 VAC

Tower/Rack-Mount6U

Uninterruptible Power Supply

990-2687B04/2006

Introduction

The APC Smart-UPS®RT is ahigh-performance,uninterruptible power supply (UPS) that provides protection for electronic equipment from utility power blackouts, brownouts, sags and surges. The UPS filters small utility line fluctuations and isolates electronic equipment from large disturbances by internally disconnecting from utility line power. The UPS provides continuous power from the internal battery until utility power returns to safe levels or the battery is fully discharged.

INSTALLATION

Read the Safety Instruction sheet before installing the UPS.

Unpacking

Inspect the UPS upon receipt. Notify the carrier

Literature kit containing:

and dealer if there is damage.

Software CD

The packaging is recyclable; save it for reuse or dispose of it properly.

Check the package contents.

UPS

Front bezel

Smart-UPSUser Manuals CD

Serial cable

Six output power cords

Two battery cable assemblies

Two ground wires

Product documentation, warranty information, and safety information

Network Management Card

documentation

Specifications

TEMPERATURE

32° to 104° F (0° to 40° C)

This unit is intended for

OPERATING

indoor use only. Select a

STORAGE

5° to 113° F(-15to 45° C) charge UPS battery every six months

location sturdy enough to

 

 

handle the weight.

MAXIMUM

 

 

Do not operate the UPS where

ELEVATION

 

OPERATING

10,000 ft (3,000 m)

there is excessive dust or the

STORAGE

50,000 ft (15,000 m)

temperature and humidity are

 

 

outside the specified limits.

HUMIDITY

0% to 95% relative humidity, non-condensing

Ensure the air vents on the

 

 

 

 

front and rear of the UPS

 

 

are not blocked.

 

 

 

WEIGHT

244 lbs (111 kg)

 

UPS

 

UPS WITH

284 lbs (129 kg)

 

PACKAGING

 

 

1

ATTACH THEBEZEL TO THEUPS

HARDWIRINGINSTRUCTIONS

Wiring must be performed by a qualified electrician.

Adhere to all national and local electrical codes.

Install a utility circuit breaker for input wiring, (see tables below).

220/230/240 V MODELS

Input Connections

 

 

 

 

 

 

 

Output Connection (optional)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Single-Phase:Wire to L1, N, and

 

.

 

 

 

Wire to L1A, N1, and

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Three-Phase:Wire to L1, L2, L3, N, and

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

System

 

Wiring

Number

 

Voltage

 

Current

 

External Input

Wire

 

 

 

of

 

 

 

 

 

Full Load

 

Circuit Breaker

Size

 

 

 

Phases

 

 

 

 

(Nominal)

 

(Typical)

(Typical)

SURT8000

 

Input

1

 

 

 

220/230/240 V

 

40 A

 

50 A / 2-pole

10mm2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input

3+

 

 

380/400/415 V

 

15

A / phase when

 

50 A / 4-pole

10mm2

 

 

 

Neutral

 

 

 

 

online

 

 

 

 

 

 

 

 

 

 

 

 

 

40

A on L1 in bypass

 

 

 

 

 

Output

1

 

 

 

220/230/240 V

 

40

A

 

(not required)

10mm2

 

 

 

 

 

 

 

 

 

 

 

 

 

SURT10000

 

Input

1

 

 

 

220/230/240 V

 

50 A

 

63 A / 2-pole

16mm2

 

 

Input

3+

 

 

380/400/415 V

 

18

A / phase when

 

63 A / 4-pole

16mm2

 

 

 

Neutral

 

 

 

 

online

 

 

 

 

 

 

 

 

 

 

 

 

 

50

A on L1 in bypass

 

 

 

 

 

Output

1

 

 

 

220/230/240 V

 

50

A

 

(not required)

16mm2

2

1.Switch the UPS input circuit breaker (see A in diagram) and utility circuit breakers OFF.

2.Remove the input access panel, (see B in diagram).

3.Remove circular knockout.

4.Run appropriate size wire through the access panel, and connect to the terminal block, (Green: Ground, Brown: Hot, Blue: Neutral). Connect the ground wire first. Use appropriate strain reliefs, (not included).

5.For three-phaseinput, set the input phase selector switch, (seeC in diagram) to “3”. Forsingle-phaseinput, leave the switch in the default position of “1”.

6.Replace the access panel.

3

CIRCUITBREAKERS

8000/10000 VA

The input circuit breaker must be switched on for the UPS to operate.

 

 

 

 

 

 

 

The input circuit breaker protects the UPS from extreme overload

 

 

 

 

 

 

 

 

 

 

 

 

 

 

conditions.

 

Input Circuit

 

 

 

 

Breaker

 

 

 

 

 

 

 

 

 

 

8000/10000 VA

IEC 320-C13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Output Circuit

10 A total current

IEC 320-C19

from four

Breakers

16 A for each

receptacles

 

 

 

 

 

 

 

receptacle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BASICCONNECTORS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power management software and interface kits can be used with the UPS.

Serial Com

Use only interface kits supplied or approved by APC.

 

Any other serial interface cable will be incompatible with the UPS

 

 

 

 

 

 

 

connector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connect the UPS to the network using the Network Management Card.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ethernet Port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Emergency Power Off terminal allows the user to connect the UPS to the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

central EPO system.

 

EPO Terminal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The UPS features a transient voltage surge-suppression(TVSS) screw for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connecting the ground lead on surge suppression devices such as telephone

TVSS Screw

and network line protectors.

 

 

 

 

 

 

 

 

When connecting grounding cable, disconnect the unit from the utility

 

 

 

 

 

 

 

power outlet.

 

 

 

 

 

 

 

 

External battery packs must be connected to these connectors located on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the rear panel of the unit.

 

External Battery

 

 

 

 

Pack Connectors

 

 

 

4

CONNECT THEEXTERNALBATTERIES

Battery Safety

Read and adhere to the following warnings when installing or servicing the external batteries.

Failure to observe these warnings may result in serious injury, death or damage to the equipment.

WARNINGS

Do not attempt to install or service external batteries alone.A qualified

 

 

 

electrician should perform the installation and servicing of external

 

 

 

batteries.

 

 

 

 

Disconnect charging source(s)BEFORE connecting or disconnecting battery

 

 

 

 

 

 

terminals.

 

 

 

 

External batteries may retain lethal voltages after power has been disconnected

 

 

 

and all switches are off.

 

 

 

Use extreme caution when making terminal connections. Do not allow cables

 

 

 

to touch anything except the intended terminal.

 

 

PRACTICES

Always wear: Goggles or face shields

 

 

 

 

Acid-resistant,insulated gloves

 

 

 

 

Protective aprons

 

 

 

 

Protective overshoes or rubber boots

 

 

 

Always Use:

Insulated tools

 

 

 

 

Rubber mats to cover batteries during servicing

 

 

 

 

Rubber mats or rubber stands on the floor

 

 

 

 

Adequate lifting devices

 

 

 

Remove:

Watches, rings, and other metal objects from your body

 

 

PRECAUTIONS

To avoid staticbuild-up,service personnel should establish a grounding

 

 

 

contact prior working on batteries.

 

 

 

Do not lay tools or metal parts on top of batteries.

 

 

 

Lead-acidbatteries contain hazardous, toxic materials.

 

 

 

Do not open, alter or mutilate batteries. Internal materials may be harmful

 

 

 

to the skin and eyes.

 

 

 

Do not dispose of batteries in a fire. There is danger of explosion.

 

 

 

Handle, transport and recycle batteries in accordance with local codes and

 

 

 

regulations.

 

 

 

 

 

APC BATTERYSOLUTION

See the APC Web site www.apc.com, or contact your APC dealer for information regarding the APC external battery pack.

5

THIRDPARTYBATTERYSOLUTION

Batteries must be Sealed Lead-Acidtype. Use 50 A, 250 VDC fuses with an Interrupt rating of20,000 A.

Ensure that the external batteries are wired prior to connecting the batteries to the UPS.

Two separate, isolated 192 V battery systems are required when using a third party battery solution. One cable assembly must be wired to each 192 V battery system. Two cable assemblies are included with the UPS, one for each 192 V battery system.

Connect the Ground and Wire the Battery System

1.Connect the ground wires (included), to each battery enclosure ground and the TVSS screw on the back of the UPS.

2.Cut off one of the connectors on each cable assembly revealing the positive and negative wires in each cable.

3.Connect the positive (red), and negative (black) wires to the positive and negative terminals on each external battery system. Ensure that the proper polarities are connected.

4.Plug the cable connectors into the battery connector receptacles on the back of the UPS.

Battery

System 1

Battery

System 2

6

CONNECTEQUIPMENT ANDPOWER TO THEUPS

1.Connect equipment to the UPS.

2.Turn on all connected equipment. To use the UPS as a master ON/OFF switch, ensure all connected equipment is switched ON. The equipment will not be powered until the UPS is turned on.

3.Switch the utility circuit breaker on.

4.To power up the UPS press the button on the front panel.

The UPS battery charges when it is connected to utility power.

Allow at least 24 hours for the batteries to fully charge prior to connecting equipment to the UPS.

5.Configure the Network Management card. Refer to the Network Management card user manual.

7

TERMINALMODE TOCONFIGUREUPS PARAMETERS ANDPROGRAM THENUMBER OFBATTERYPACKS

Terminal Mode is a menu driven interface that enables enhanced configuration of the UPS. Connect the serial cable from the computer to the serial com connector on the back of the UPS. Instructions for use with PowerChute Network Shutdown software:

1.Open a terminal program. Example: HyperTerminal

From the Desktop, go to Start=> Programs=> Accessories=> Communication=>HyperTerminal.

2.Double-clickon theHyperTerminal icon.

Follow the prompts to choose a name and select an icon. Disregard the message, “...must install a modem,” if it is displayed. Click OK.

Select the COM port that is connected to your UPS. The port settings are:

9bits per second - 2400

9data - bits 8

9parity - none

9stop bit - 1

9flow control - none

Press ENTER

3.Example for setting the number of external battery packs:

Once the blank terminal window is open, follow these steps to enter the number of battery packs:

Press ENTER to initiate terminal mode. Press ENTER multiple times, until the prompt User Name: is displayed. Follow the prompts. Type slowly, waiting until each character appears on the screen prior to typing the next character.

Network Management card defaults:

User Name: apc

Password: apc

Press 1 and ENTER to select Device Manager.

Select the model by entering the corresponding number, then press Enter.

Press 3 and ENTER to select Configuration.

Press 1 and ENTER to select Battery.

Press 2 and ENTER to change the Battery Settings.

Type in the number of external battery packs.

Number of packs: 1= 1920 VAh, 2 = 3840 VAh, 3 = 5760 VAh, etc.

Press 3 and ENTER to accept the changes.

Press ESC multiple times (5) to return to the main menu.

Press 4 and ENTER to log out.

8