American Power Conversion 2200 VA, 120 Vac, 230 Vac, 3000 VA, 100 Vac, 120 Vac, 208 Vac, 230 Vac User Manual

Size:
325.1 Kb
Download

User Manual

English

APC Smart-UPS®

2200 VA

120/230 Vac

3000 VA

100/120/208/230 Vac

2U Rack Mount

Uninterruptible Power Supply

990-1352A11/2003

Introduction

The APC Uninterruptible Power Supply (UPS) is designed to prevent blackouts, brownouts, sags, and surges from reaching your equipment. The uninterruptible power supply (UPS) filters small utility line fluctuations and isolates your equipment from large disturbances by internally disconnecting from the utility line. The UPS provides continuous power from its internal battery until the utility line returns to safe levels or the battery is fully discharged.

1:INSTALLATION

Unpack

Read the Safety Guide before installing the UPS. The User Manual and Safety Guide are accessible on the supplied User Manuals CD and on the APC web site, www.apc.com.

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly. Check the package contents:

UPS Front bezel Rail kit

UPS literature kit containing: Smart-UPS® User Manuals CD

120/208/230 V Models Only: PowerChute® CD, Serial and USB communication cables

Product documentation, safety and warranty information

Rack mounting brackets

 

EPO Connector

 

Hardware

 

230 V Models Only:

 

Input power cord

Utility connector plug

Alternate input power cord

IEC Jumper cords

UK customers

 

Rail Installation

Install the rails following the instructions in the rail kit.

Placement of the UPS

The UPS is heavy. Select a location sturdy enough to handle the weight.

Do not operate the UPS in excessive dust or in temperature and humidity outside the specified limits.

PLACEMENT

1

Mount the UPS in a Rack

Your UPS model may vary from the examples depicted in this manual.

Install brackets as shown, or at a 5 in (12.7 cm) setback.

Remove the battery module to lighten the UPS during installation. Note: The module is heavy.

Install the UPS at or near the bottom of the

Reinstall the battery module.

rack.

 

Connect the battery module.

Attach the front bezel.

2

Connect Equipment and Power to the UPS

Startup

1.Connect equipment to the UPS. A laser printer draws significantly more power than other types of equipment and may overload the UPS.

2.Add optional accessories to the Smart-Slot.

3.Plug the UPS into a two-pole,three-wire,grounded receptacle only. Avoid using extension cords.

230 V model: The power cord is supplied in the UPS cable kit. The TVSS ground, located on the rear panel of the UPS must be connected prior to connecting the utility power.

4.120 V model: Check thesite wiring fault LEDlocated on the rear panel. It will be illuminated if the UPS is plugged into an improperly wired utility power outlet, (seeTroubleshooting).

5.Turn on all connected equipment. To use the UPS as a master on/off switch, be sure all connected equipment is on.

6.Press the button on the front panel to power the UPS.

The battery charges to 90% capacity during the first four hours of normal operation. Do not expect full battery run capability during this initial charge period.

7.For optimal computer system security, install PowerChute Smart-UPSmonitoring software.

Rear Panels

100/120 V

208 V

230 V

3

Basic Connectors

 

 

Serial

USB

TVSS

Use only interface kits approved by APC.

Port

Port

Screw

 

Use only the supplied cable to connect to the Serial Port. A standard serial interface cable is incompatible with the UPS.

Serial and USB Ports cannot be used simultaneously.

The UPS features a transient voltage surge-suppression(TVSS) screw for connecting the ground lead on surge suppression devices such as telephone and network line protectors.

Prior to connecting grounding cable, disconnect the UPS from utility power.

Emergency Power Off

The Emergency Power Off (EPO) feature is user configurable. EPO provides immediate deenergizing of connected equipment from a remote location, without switching to battery operation.

1.Use the EPO connector supplied with the UPS.

2.Use a normally-opencontact to connect the +24 terminal to the IN terminal, (see diagram).

3.Wire the four-pinconnector to the EPO system.

EPO Port

EPO Connector

 

(located on rear panel)

 

IN +24

The EPO interface is a Safety Extra Low Voltage (SELV) circuit. Connect it only to other SELV circuits. The EPO interface monitors circuits that have no determined voltage potential. Such closure circuits may be provided by a switch or relay properly isolated from the utility. To avoid damage to the UPS, do not connect the EPO interface to any circuit other than a closure type circuit.

Use one of the following cable types to connect the UPS to the EPO switch:

CL2: Class 2 cable for general use

CL2P: Plenum cable for use in ducts, plenums, and other spaces used for environmental air.

CL2R: Riser cable for use in a vertical run in a floor to floor shaft.

CLEX: Limited use cable for use in dwellings and for use in raceways.

For installation in Canada: Use only CSA certified, type ELC (extra-lowvoltage control cable).

4

2: OPERATION

Front Display Panel

INDICATOR

DESCRIPTION

Online

The UPS is supplying utility power to the connected equipment (see Troubleshoot-

 

ing).

 

 

AVR Trim

The UPS is compensating for a high utility voltage.

 

 

AVR Boost

The UPS is compensating for a low utility voltage.

 

 

On Battery

The UPS is supplying battery power to the connected equipment.

 

 

Overload

The connected loads are drawing more than the UPS power rating, (see Trouble-

 

shooting).

 

 

Replace Battery/

The battery is disconnected or must be replaced, (see Troubleshooting).

Battery Discon-

 

nected

 

 

 

FEATURE

FUNCTION

Power On

Press this button to turn on the UPS, (read on for additional capabilities).

 

 

Power Off

Press this button to turn off the UPS.

 

 

5

FEATURE

FUNCTION

 

 

 

Self-Test

Automatic: The UPS performs aself-testautomatically when turned on, and every

 

two weeks thereafter, (by default). During the self-test,the UPS briefly operates

 

the connected equipment on battery.

 

 

Manual: Press and hold the

button for a few seconds to initiate the self-test.

 

 

Cold Start

When there is no utility power and the UPS is off, the cold start feature will switch

208/120/230 V

the UPS and connected equipment onto battery power, (see Troubleshooting).

models Only

 

 

 

 

 

 

Diagnostic Utility

The UPS has a diagnostic feature that displays the utility voltage.

Voltage

The UPS starts a self-testas part of this procedure. Theself-testdoes not af-

 

 

fect the voltage display.

 

 

 

Press and hold the

button to view the utility voltage bar graph display. After a

 

few seconds, this five-LEDbattery charge

display on the right of the front

 

panel will show the utility input voltage.

 

 

Refer to the figure at left for the voltage reading, (values are not listed on the

 

UPS).

 

 

 

 

The display indicates the voltage is between the displayed value on the list and the

 

next higher value, (see Troubleshooting).

 

 

 

 

 

 

Battery Operation

The UPS switches to battery operation automatically if the utility power fails. While running on battery, an alarm beeps four times every 30 seconds.

Press the button to silence this alarm. If the utility power does not return, the UPS continues to supply power to the connected equipment until the battery is fully discharged.

If PowerChute is not being used, files must be manually saved and the computer must be turned off before the UPS fully discharges the battery.

The UPS battery life differs based on usage and environment. Refer to www.apc.com for on battery runtimes.

6

3:USERCONFIGURABLEITEMS

NOTE: SETTINGS ARE ADJUSTED THROUGHPOWERCHUTE SOFTWARE

OR OPTIONAL SMARTSLOT ACCESSORY CARDS.

FUNCTION

FACTORY

USERSELECTABLE

DESCRIPTION

DEFAULT

CHOICES

 

 

 

Automatic Self-

Every 14 days

Every 7 days

Set the interval at which the UPS will

Test

(336 hours)

(168 hours),

execute a self-test.

 

 

On Startup Only,

 

 

 

 

No Self-Test

 

 

 

 

 

 

UPS ID

UPS_IDEN

Up to eight charac-

Uniquely identify the UPS, (i.e. server

 

 

ters (alphanumeric)

name or location) for network man-

 

 

 

agement purposes.

 

 

 

 

Date of Last Bat-

Manufacture Date

mm/dd/yy

Reset this date when you replace the

tery Replacement

 

 

battery module.

 

 

 

 

 

Minimum Capacity

0 percent

0, 15, 30, 45, 50, 60,

Following a low-batteryshutdown, the

Before Return from

 

75, 90 percent

battery modules will be charged to the

Shutdown

 

 

specified percentage before powering

 

 

 

connected equipment.

 

 

 

 

Voltage Sensitivity

High

: Brightly illu-

Adjust by pressing the voltage sensi-

The UPS detects

tivity button

(rear panel). Use a

 

minated - high sensi-

 

pointed object, (such as a pen) to do

and reacts to line

 

 

tivity.

 

so.

 

voltage distortions

 

 

 

 

 

by transferring to

 

: Dimly illumi-

Note: In situations of poor power qual-

battery operation to

 

nated - medium sen-

ity, the UPS may frequently transfer to

protect connected

 

sitivity.

battery operation. If the connected

equipment.

 

: No illumina-

equipment can operate normally under

 

 

such conditions, reduce the sensitivity

 

 

tion; low sensitivity.

setting to conserve battery capacity

 

 

 

and service life.

 

 

 

 

 

Alarm Delay Con-

Enable

Enable, Mute, Dis-

Mute ongoing alarms or disable all

trol

 

able

alarms permanently.

 

 

 

 

Shutdown Delay

90 seconds

0, 90, 180, 270, 360,

Set the interval between the time when

 

 

450, 540, 630 sec-

the UPS receives a shutdown com-

 

 

onds

mand and the actual shutdown.

 

 

 

 

 

7

NOTE: SETTINGS ARE ADJUSTED THROUGHPOWERCHUTE SOFTWARE

OR OPTIONAL SMARTSLOT ACCESSORY CARDS.

FUNCTION

 

FACTORY

USERSELECTABLE

DESCRIPTION

 

DEFAULT

CHOICES

 

 

 

Low Battery Warn-

 

2 minutes

: Brightly illu-

The UPS will beep when 2 minutes of

ing

 

battery runtime remains.

 

PowerChute soft-

minated - low bat-

Change the warning interval setting by

 

tery warning level of

 

ware provides

about 2 minutes.

pressing the voltage sensitivity button,

 

automatic, unat-

 

while pressing and holding the

 

tended shutdown

: Dimly illumi-

 

when approxi-

button.

 

nated - low battery

 

mately 2 minutes

 

 

warning level of

Change the low battery warning inter-

 

of battery oper-

 

about 5 minutes.

val setting to the time that the operat-

 

ated runtime re-

 

 

ing system or system software requires

 

mains.

: No illumina-

 

to safely shut down.

 

 

 

 

 

 

tion; low battery

 

 

 

 

warning level is

 

 

 

 

approximately 8

 

 

 

 

minutes.

 

 

 

 

 

Synchronized

0 seconds

0, 60, 120, 180, 240,

Specify the time the UPS will wait

Turn-onDelay

 

 

300, 360, 420 sec-

after the return of utility power before

 

 

 

onds

turn-on,(to avoid branch circuit over-

 

 

 

 

load).

 

 

 

 

 

High Transfer

100

V model:

100 V model:

Set the high transfer point higher to

Point

108

Vac

108, 110, 112,

avoid unnecessary battery usage when

 

120

V model:

114 Vac

the utility voltage is usually high and

 

127

Vac

120 V model:

the connected equipment is specified

 

208

V model:

127, 130, 133,

to operate with input voltages this

 

225

Vac

136 Vac

high.

 

230

V model:

208 V model:

 

 

253

Vac

225, 229, 233,

 

 

 

 

237 Vac

 

 

 

 

230 V model:

 

 

 

 

253, 257, 261,

 

 

 

 

265 Vac

 

 

 

 

 

 

Low Transfer Point

100

V model:

100V model:

Set the low transfer point lower when

 

92 Vac

92, 90, 88, 86 Vac

the utility voltage is usually low and

 

120

V model:

120 V model:

the connected equipment is specified

 

106

Vac

97, 100, 103,

to operate with input voltages this low.

 

208

V model:

106 Vac

 

 

182 Vac

208 V model:

 

 

230

V model:

170, 174, 178,

 

 

208 Vac

182 Vac

 

 

 

 

230 V model:

 

 

 

 

196, 200, 204,

 

 

 

 

208 Vac

 

 

 

 

 

 

Output Voltage

230

Vac

220, 230, 240 Vac

Select the output voltage.

230 V Model Only

 

 

 

 

 

 

 

 

 

 

 

 

8