Amana ARB9058CB, ARB8057CC, ARB9058CW, ARS2664BC, ARSE66MBC User Manual

...
0 (0)
Part No. 12642704
Printed in U.S.A.
©2002 Maytag Appliances Sales Co.
Form No. B/07/02
Bottom Freezer
Refrigerator
Ordering parts and accessories?
Questions about your features?
Consumer Affairs Department
Amana Appliances
2800 - 220th Trail
Amana, Iowa 52204
Ph# 1(800)843-0304 in U.S.A.
1(866)587-2002 au Canada
Internet: http:// www.amana.com
Owner’s Manual
Keep instructions for future reference.
Keep this manual and your sales receipt together in a safe place
in case warranty service is required.
Contents
Introduction .................................................................2
Important Safety Information ......................................3
Installing Your Refrigerator .........................................4
How to Remove the Doors and Hinges....................4
How to Reverse Refrigerator Door...........................5
How to Install and Remove Handles........................6
How to Replace the Doors and Hinges....................7
How to Remove and Install Panels ..........................7
How to Remove and Install the Pullout Drawer .......8
How to Connect the Water Supply...........................9
How to Level Your Refrigerator ..............................10
How to Adjust the Temperature Controls................10
About Your Water Filter.............................................11
Fresh Food Features ................................................12
Primary Features....................................................12
Interior Shelves.......................................................12
Door Storage ..........................................................12
Accessories ............................................................12
Climate-Controlled Drawers ...................................13
Freezer Features ......................................................14
Primary Features....................................................14
Drawers ..................................................................14
Accessories ............................................................14
Hints and Care..........................................................15
How to Clean Your Unit..........................................15
How to Remove and Replace Light Bulbs .............16
Trouble Shooting.......................................................17
Water Filter Data.......................................................20
Warranty ...................................................................22
2
Thank you for buying an Amana refrigerator!
Please read this Owner's Manual thoroughly. This manual provides proper maintenance
information.
Complete registration card and promptly return. If registration card is missing, call
the Consumer Affairs Department.
Warranty service must be performed by an authorized servicer. Amana also
recommends contacting an authorized servicer if service is required after warranty
expires. To locate an authorized servicer, call 1-800-NAT-LSVC (1-800-628-5782). You
may also contact us on the web at www.amana.com.
When contacting Amana, please provide the following information. Product information
is on the serial plate, located on ceiling of fresh food section.
Model Number ________________________________________________________
'P' Number ___________________________________________________________
Serial Number _________________________________________________________
Purchase Date ________________________________________________________
Dealer Name _________________________________________________________
Dealer Address ________________________________________________________
Dealer Phone _________________________________________________________
Asure™ extended
service plan
Amana offers long-term service protec-
tion for this new refrigerator. Asure™
Extended Service Plan is specially
designed to supplement Amana’s strong
warranty. This plan covers parts, labor,
and travel charges. Call 1(800)528-2682,
or contact us at www.amana.com for
more information.
Before calling service...
If something seems unusual, please
check “Trouble Shooting” section, which
is designed to help you solve problems
before calling service.
What if these features
are different from
mine?
This book is intended to show the variety
of features that are available in the prod-
uct line. If your refrigerator does not have
all the options that are shown, many of
these options may be purchased by con-
tacting the Consumer Affairs Department.
See contact information on the cover of
your manual.
3
Important safety information
What you need to know
about safety
instructions
Warning and Important Safety
Instructions appearing in this manual are
not meant to cover all possible conditions
and situations that may occur. Common
sense, caution, and care must be
exercised when installing, maintaining, or
operating refrigerator.
Always contact your dealer, distributor,
service agent, or manufacturer about
problems or conditions you do not under-
stand.
Save these instructions
DANGER – Immediate hazards which
WILL result in severe personal injury
or death.
DANGER
WARNING – Hazards or unsafe prac-
tices which COULD result in severe
personal injury or death.
WARNING
CAUTION – Hazards or unsafe prac-
tices which COULD result in minor
personal injury.
CAUTION
To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic precautions,
including the following:
WARNING
To reduce risk of injury or death,
follow basic precautions, including
the following:
IMPORTANT: Child entrapment and
suffocation are not problems of the
past. Junked or abandoned refrigera-
tors are still dangerous – even if they
sit out for “just a few days.” If you are
getting rid of your old refrigerator,
please follow the instructions below to
help prevent accidents.
Before you throw away your old refrig-
erator or freezer:
Take off the doors.
Leave the shelves in
place so children
may not easily climb
inside.
DANGER
RECOGNIZE SAFETY
SYMBOLS, WORDS,
LABELS
1. Read all instructions before using the refrigerator.
2. Observe all local codes and ordinances.
3. Be sure to follow grounding instructions.
4. Check with a qualified electrician if you are not sure this
appliance is properly grounded.
5. DO NOT ground to a gas line.
6. DO NOT ground to a cold-water pipe.
7. Refrigerator is designed to operate on a separate 103 to
126 volt, 15 amp., 60 cycle line. DO NOT modify plug on
power cord. If plug does not fit electrical outlet, have proper
outlet installed by a qualified electrician.
8. DO NOT use a two-prong adapter, extension cord or power
strip.
9. DO NOT remove warning tag from power cord.
10. DO NOT tamper with refrigerator controls.
11. DO NOT service or replace any part of refrigerator unless
specifically recommended in Owner’s Manual or published
user-repair instructions. DO NOT attempt service if instructions
are not understood or if they are beyond personal skill level.
12. Always disconnect refrigerator from electrical supply before
attempting any service. Disconnect power cord by grasping
the plug, not the cord.
13. Install refrigerator according to Installation Instructions. All
connections for water, electrical power and grounding must
comply with local codes and be made by licensed person-
nel when required.
14. Keep your refrigerator in good condition. Bumping or drop-
ping refrigerator can damage unit or cause unit to malfunc-
tion or leak. If damage occurs, have refrigerator checked by
qualified service technician.
15. Replace worn power cords and/or loose plugs.
16. Always read and follow manufacturer’s storage and ideal
environment instructions for items being stored in refrigerator.
1. Unplug power cord from power
source.
2. Remove toe
grille and bot-
tom bracket
cover.
Open freezer door
(some models) as wide as possible.
3. Remove top hinge
cover from refriger-
ator door by remov-
ing Phillips screw
(non-trim models
only).
Retain screw and cover for replace-
ment.
4. Remove top door trim with Phillips
screw (trim models only).
Retain screw and trim for replace-
ment.
5. Unscrew
5
Ú16" hex
head screws from
top hinge to
remove hinge.
Retain hinge and all screws for later
use.
6. Lift refrigerator door from center hinge
pin.
7. Remove center
hinge pin with a
5
Ú16" hex nut driver.
Retain hinge pin
for later use.
8. Remove Phillips
screws to remove
center hinge.
Retain hinge and all screws for later
use.
9. Remove both stabilizing brackets with
3
Ú8" hex head driver.
•Retain screws and brackets for later
use.
4
Installing your refrigerator
These instructions were provided to aid
you in the installation of your refrigerator.
Amana is not responsible for improper
installation.
Measuring the opening
A
1
Ú2" of air space should be provided for
the top and back of the unit to allow for
proper air circulation. When installing
your unit, measure carefully.
Subflooring or floor coverings (i.e. carpet,
tile, wood floors, rugs) may make your
opening smaller than anticipated.
Some clearance may be gained by using
the leveling procedure under How to
Level Your Refrigerator.
IMPORTANT: If unit is to be installed into
a recess where top of unit is completely
covered, use dimensions from floor to top
of hinge cap to verify proper clearance.
Transporting your
refrigerator
Follow these tips when moving the unit to
final location:
NEVER transport unit on its side. If an
upright position is not possible, lay unit
on its back. Allow unit to sit upright for
approximately 30 minutes prior to
plugging unit in to assure oil return to
the compressor. Plugging unit in
immediately may cause damage to
internal parts.
Use an appliance dolly when moving
unit. ALWAYS truck unit from its
side–NEVER from its front or back.
Protect outside finish of unit during
transport by wrapping cabinet in blan-
kets or inserting padding between the
unit and dolly.
Secure unit to dolly firmly with straps
or bungee cords. Thread straps
through handles when possible. DO
NOT overtighten. Overtightening
restraints may dent or damage outside
finish.
Selecting the best
location
Observe these points when choosing the
final location for your unit:
DO NOT install refrigerator near oven,
radiator or other heat source. If not
possible, shield unit with cabinet
material.
DO NOT install where temperature
falls below 55° F (13° C). Malfunction
may occur at this temperature.
Make sure floor is level. If floor is not
level, shim rear wheels of unit with a
piece of plywood or other shim material.
To assure proper door closure, verify
that the unit is leveled with a
1
Ú4" tilt to
the back.
How to remove the
doors and hinges
Some installations require door removal
to get refrigerator to final location.
To avoid electrical shock which can
cause severe personal injury or death,
observe the following:
Disconnect power to refrigerator
before removing doors. Connect
power only after replacing doors.
WARNING
To avoid damage to walls and flooring,
protect soft vinyl or other flooring with
cardboard, rugs or other protective
material.
CAUTION
5
How to reverse
refrigerator door
DOORS WITH TRIM AND
PANELS
1. Perform all steps listed in How to
Remove the Doors and Hinges.
2. Transfer cabinet
plugs and screws to
opposite side of
cabinet.
3. Remove plugs with flat blade of screw-
driver wrapped in masking tape.
4. Remove center mullion screws with
5
Ú16
" hex head driver.
IMPORTANT: When working directly on
doors, place doors on a nonabrasive sur-
face protected by towels or rugs to avoid
damage to door finish.
5. Locate door stop (A) and door cap (B)
on bottom edge of fresh food door.
Remove with a Phillips screwdriver.
Retain all items for later replace-
ment.
6. Remove top door extension with
1
Ú4"
hex head driver. Flip door extension
(A) so notched corner turns in toward
interior of door (B).
7. Remove side door trim (A) and handle
trim (B) from door by tapping bottom
edges upward with soft rubber mallet.
•Trim will slide up approximately
3
Ú4"
and release from door.
8. Replace bottom door cap removed
previously. Install door stop on oppo-
site side of door.
9. Retrieve alternate side door trim
shipped with refrigerator. Install trim
by aligning notches of trim with metal
mounting tabs on side of door.
Slide trim down until piece locks into
place.
•Tap top of trim with rubber mallet to
insure snug fit.
10 . Remove tape from panels.
11. Proceed to How to Install and
Remove Handles to reinstall handle.
To avoid possible injury and damage
to property, tape decorative panels
(some models) securely into place
before removing side door trim and
handles.
WARNING
STANDARD
REFRIGERATOR DOOR
1. Perform all steps listed in How to
Remove the Doors and Hinges.
2. Transfer cabinet
plugs and cabinet
screws to opposite
side of cabinet.
3. Remove cabinet
plugs with flat blade screwdriver tip
wrapped in masking tape.
4. Remove center mullion screws with
5
Ú16" hex head driver.
5. Transfer door stop to opposite edge of
door using Phillips screwdriver.
IMPORTANT: When working directly on
doors, place doors on a nonabrasive sur-
face protected by towels or rugs to avoid
damage to door finish.
6. See How to Install and Remove
Handles to remove and reinstall
handles.
7. Proceed to How to Replace the
Doors and Hinges to mount doors.
B
A
B
A
A
B
6
Installing your refrigerator,
cont.
How to install and
remove handles
REMOVING TRIM AND
PANEL FRESH FOOD
HANDLE
Removing handles is necessary when
removing panels, or when reversing the
door.
1. Remove top door cap using a Phillips
screwdriver.
2. Remove handle from
door by tapping
bottom edge upward
with soft rubber
mallet.
Handle will slide up approximately
3
Ú4"
and release from door.
INSTALLING TRIM AND
PANEL FRESH FOOD
HANDLE
Installing handles may be necessary after
reversing door or installing a panel.
1. Make sure bottom door cap is installed
and top door cap is removed.
Use a Phillips screwdriver for instal-
lation and removal.
2. Install handle by
aligning handle
notches with
metal mounting
tabs on side of door.
Slide handle down until piece locks.
•Tap top of handle with rubber mallet
to insure snug fit.
IMPORTANT: If reversing trim and panel
door, use alternate top hinge shipped
with refrigerator.
3. Install top door cap with Phillips
screwdriver.
INSTALLING FRESH FOOD
SIDE-MOUNTED HANDLE
If installing handles for the first time, the
Fresh Food handles can be located on
the back of the refrigerator.
Install handle
by fastening
with T-15
Torx
®
* screws
removed from
edge of door.
NOTE: If revers-
ing door, remove door plugs from oppo-
site side of door and insert in screw
holes.
REMOVING FRESH FOOD
SIDE-MOUNTED HANDLE
Removing handles may be necessary
when transporting unit through tight
spaces, or when reversing the door.
Remove
handle by
removing
three
T-15 Torx
®
*
screws
from side of
door.
Retain screws for later replacement.
* Torx
®
is a registered trademark of Textron Inc.
To avoid risk of serious personal injury
from sharp edges, use extreme
caution when removing and installing
handles.
WARNING
INSTALLING STAINLESS
STEEL FRONT -MOUNTED
HANDLES
1. Loosen door clip on door
with
1
Ú4" hex nut driver.
2. Locate predrilled hole at
base of handle, and fit
hollow end of handle
over door clip.
3. Fit other end of handle
over other door clip and
slide handle up as far as possible.
NOTE: If top of handle does not fit over
top clip, loosen lower clip further until fit
can be accomplished.
4. Insert
1
Ú4" hex nut driver
into predrilled hole at
base of handle to tight-
en screw. Insert screw
plug into hole.
REMOVING STAINLESS
STEEL FRONT-MOUNTED
HANDLES
1. Remove screw plug at base of handle
with a very small flat-blade screw-
driver.
2. Insert
1
Ú4" hex nut driver into predrilled
hole to remove screw.
3. Slide handle down and
out to remove from
door clip.
To remove panels, remove door han-
dle and slide panel out the handle side
of door.
Install panels by sliding panel in
grooves provided by bottom door cap
and side trim.
Replace the
handles, when
completed.
7
How to replace the
doors and hinges
1. Install hinge assemblies.
2. Install center hinge with Phillips
screws.
3. Install stabilizing bracket with
3
Ú8" hex
head screws.
4. Install center
hinge pin with
5
Ú16"
hex head driver.
5. Place hinge side of refrigerator door
on center hinge pin.
6. While holding refrigerator door
upright, tighten down top hinge with
5
Ú16" hex head driv-
er. Replace hinge
cover (some mod-
els).
To avoid personal injury or property
damage, fresh food panel should not
weigh more than 30 lbs (14 kgs) and
freezer panel should not weigh more
than 15 lbs (7 kgs).
WARNING
How to remove and
install panels
(SOME MODELS)
WHAT IF I AM INSTALLING
RAISED PANELS?
If raised panels are used, allow 2
1
Ú2" (A)
minimum clearance between raised edge
of panel and handle.
Please see the recommended dimen-
sions for panelling.
Raised Panel B – 42" x 35
5
Ú8"
(106.7 cm x 90.5 cm)
Raised Panel C – 23
1
Ú4" x 36
1
Ú16"
(59.1 cm x 91.6 cm)
B
C
8
Installing your refrigerator,
cont.
How to remove and
install the pullout
drawer
To avoid electrical shock which can
cause severe personal injury or death,
disconnect power to refrigerator
before removing doors. After replacing
doors, connect power.
WARNING
To avoid possible injury, product, or
property damage, you will need two
people to perform the following
instructions.
CAUTION
REMOVING PULLOUT
DRAWER
1. Pull drawer open to full extension.
Remove Phillips screw from each side
of rail system.
2. Remove lower basket by lifting basket
from rail system.
3. Pull upper basket out to full extension,
and lift out to remove.
4. Lift top of door to unhook door
supports from rail system. Lift door out
to remove.
INSTALLING PULLOUT
DRAWER
1. Pull both rails out to full extension.
2. Hook door supports into rail tabs, as
illustrated, and lower door into final
position.
3. With drawer pulled out to full exten-
sion, insert lower basket by aligning
tabs on both side of lower basket with
notches in rail assembly.
4. Slide upper basket into unit. Make
sure that rear of basket hooks behind
rail catch.
4. Place end of copper tubing into water
valve inlet port. Shape tubing slightly –
DO NOT KINK – so that tubing feeds
straight into inlet port.
5. Slide brass nut over sleeve and screw
nut into inlet port. Tighten nut with
wrench.
IMPORTANT: DO NOT overtighten.
Cross threading may occur.
6. Pull on tubing to confirm connection is
secure. Connect tubing to frame with
water tubing clamp (C) and turn on
water supply. Check for leaks and
correct, if present.
7. Monitor water connection for 24 hours.
Correct leaks, if necessary.
9
How to connect the
water supply
To reduce the risk of injury or
death, follow basic precautions,
including the following:
Read all instructions before
installing device.
DO NOT attempt installation if
instructions are not understood or if
they are beyond personal skill
level.
Observe all local codes and ordi-
nances.
DO NOT service device unless
specifically recommended in
owner’s manual or published user-
repair instructions.
Disconnect power to unit prior to
installing device.
WARNING
To avoid property damage or possi-
ble injury, follow basic precautions,
including the following:
Consult a plumber to connect
copper tubing to household plumb-
ing to assure compliance with local
codes and ordinances.
Confirm water pressure to water
valve is between 20 and 100
pounds per square inch. If water
filter is installed, water pressure to
water valve must be a minimum of
35 pounds per square inch.
DO NOT use a self-piercing, or
3
Ú16"
saddle valve! Both reduce water
flow, become clogged with time,
and may cause leaks if repair is
attempted.
Tighten nuts by hand to prevent
cross threading. Finish tightening
nuts with pliers and wrenches. Do
not overtighten.
Wait 24 hours before placing unit
into final position to check and
correct any water leaks.
CAUTION
MATERIALS NEEDED
1
Ú4" outer diameter flexible copper
tubing
Shut-off valve (requires a
1
Ú4" hole to be
drilled into water supply before valve
attachment)
Adjustable wrench
1
Ú4" hex nut driver
NOTE: Add 8' to tubing length needed to
reach water supply for creation of service
loop.
1. Create service loop with tubing using
care to avoid kinks in tubing.
2. Remove plastic cap from water valve
inlet port.
C
3. Place brass nut (A) and sleeve (B) on
copper tube end as illustrated.
A
B
10
Installing your refrigerator,
cont.
How to level your
refrigerator
If your refrigerator requires an ice maker
water supply connection, proceed to How
to connect the water supply section
before leveling your refrigerator.
To protect personal property or unit
from damage, observe the following:
Protect soft vinyl or other flooring
with cardboard, rugs, or other
protective material.
Do not use power tools when
performing leveling procedure.
CAUTION
MATERIALS NEEDED
3
Ú8" hex head driver
Level
1. Remove toe grille and bottom hinge
covers (see previous instructions).
2. Turn both front adjustment screws (A)
clockwise to raise and counter-
clockwise to lower.
3. Turn both rear adjustment screws (B)
clockwise to raise and counterclock-
wise to lower.
4. Turn stabilizing legs (C) clockwise
until firmly against floor.
5. Turn front roller adjustment screws (A)
2 to 3 times counterclockwise, so that
full weight of unit rests on stabilizing
legs (C).
6. Using a level, make sure front of
refrigerator is
1
Ú4" (6 mm) or
1
Ú2 bubble
higher than back of refrigerator. See
leveling step 3 for assistance.
7. Replace toe grille and bracket
cover(s). See markings on inside of
toe grille to insure proper placement.
Snap bottom portion into place
first. Press down on top part of grille
until top portion snaps into place.
How to adjust the
temperature controls
This refrigerator is designed to operate at
a household temperature of 55° to 110° F
(13° to 43° C). For initial temperature
setting, follow all five steps listed below. If
doing a simple temperature modification
for an operational unit, only steps 3
through 5 are required.
A
B
A
C
1. Locate refrigerator controls at the top
of fresh food compartment and freezer
controls at top of freezer section. Set
both controls to 4.
IMPORTANT: Neither section will cool if
freezer control is set to Off.
2. Allow 24 hours for temperatures to
stabilize.
3. Check to see if
freezer tempera-
ture is 0° to 2° F
(-17° to -16° C).
Turn control to next highest number
if too warm.
Turn control to next lowest number
if too cold. Allow 5 to 8 hours for
adjustments to take effect.
4. Check to see that
fresh food section
is 38° to 40° F
(3° to 4° C).
Turn control to next highest number
if too warm.
Turn control to next lowest number
if too cold.
Allow 5 to 8 hours for adjustments
to take effect.
5. Repeat steps 3 & 4, as necessary.
HOW DO I PERFORM A
TEMPERATURE TEST?
MATERIALS NEEDED
2 thermometers measuring -5° to
50° F (-21° to 10° C)
2 drinking glasses
For Freezer
Place thermometer in glass of
vegetable oil in middle of freezer and
continue with step 3 of temperature
adjustment section.
IMPORTANT: Always start temperature
adjustments with freezer section.
For Refrigerator
Place thermometer in glass of water in
middle of unit and continue with step 3
of temperature adjustment section.
11
About your water filter...
Water filter removal and
installation
To avoid serious illness or death, do
not use unit where water is unsafe or
of unknown quality without adequate
disinfection before or after use of filter.
WARNING
Bypass cartridge DOES NOT filter
water. Be sure to have replace-
ment cartridge available when filter
change is required.
If water filtration system has been
allowed to freeze, replace filter
cartridge.
If system has not been used for
several months, and water has an
unpleasant taste or odor, flush
system by dispensing 2–3 glasses
of water. If unpleasant taste or odor
persists, change filter cartridge.
CAUTION
INITIAL INSTALL OF
WATER FILTER
1. Remove blue bypass cap and retain
for later use.
2. Remove sealing label from end of filter
and insert into filter head.
3. Rotate gently clockwise until filter
stops, and snap filter cover closed.
4. Reduce water spurts by flushing air
from system. Run water continuously
for 2 minutes through dispenser until
water runs steady.
Additional flushing may be required
in some households where water is
of poor quality.
REPLACING WATER
FILTER
IMPORTANT: Air trapped in system may
cause water and cartridge to eject. Use
caution when removing.
1. Turn filter counterclockwise until it
releases from filter head.
2. Drain water from filter into sink, and
dispose in normal household garbage.
3. Wipe up excess water in filter cover
and continue with Initial Install of
Water Filter, steps 2 and 3.
WHEN DO I CHANGE THE
WATER FILTER?
The filter should be changed approxi-
mately every 6 months.
IMPORTANT: Condition of water and
amount used determines life span of
water filter cartridge. If water use is high,
or if water is of poor quality, replacement
may need to take place more often.
HOW DO I ORDER A
REPLACEMENT FILTER
CARTRIDGE?
Amana
®
Replacement Water Filter car-
tridge model WF 50 is available through
Amana
®
dealers and servicers. You may
also order through Amana
®
Consumer
Affairs by using the information on the
cover of your manual.
I'M TRYING TO DISPENSE
WATER TO FLUSH THE
SYSTEM. WHERE'S THE
WATER?
During initial use, allow about a 1 to 2
minute delay in water dispersal to allow
internal water tank to fill.
WHAT IF I CHOOSE NOT
TO USE THE WATER
FILTRATION SYSTEM?
Dispenser feature may be used without
water filter cartridge. If you choose this
option, replace filter with blue bypass
cap.
12
Fresh food features
Primary features
HOW CAN I CLEAN OUT
MY WATER SUMP?
The sump has been designed for easy-
access cleaning.
The cup-style sump can be removed by
sliding straight up out of the sump frame.
It may be required to clean the sump to
remove water or mineral deposits. These
items ARE NOT dishwasher-safe. Sumps
may be washed with soap and water.
IMPORTANT: The sump does not
contain a drain.Spills must be wiped up
occasionally to remove water.
WATER DISPENSER
(SOME MODELS)
A water dispenser is
located on the left
side wall of the fresh
food section. This
design is for cold
water dispensing
only. A water sump
has been designed
below the dispenser to catch drips and
minor spills.
To dispense water:
Hold container under spout and press
dispenser pad, as illustrated.
Interior shelves
To avoid personal injury or property
damage, observe the following:
Confirm shelf is secure before
placing items on shelf.
Handle tempered glass shelves
carefully. Shelves may break
suddenly if nicked, scratched, or
exposed to sudden temperature
change.
CAUTION
FULL-WIDTH SHELF
(SOME MODELS)
To remove shelves,
unhook shelf from
rear ladder assembly
and pull out.
To install shelves, insert shelf hooks
into rear ladder assembly and lower
into place.
SPILLSAVER™
STATIONARY SHELVES
(SOME MODELS)
Spillsaver™ stationary
shelves hold simple
spills for easier cleaning.
To remove shelves, lift up
and out.
To install shelves, reverse above
procedure.
SPILLSAVER™
EASYGLIDE™
(SOME MODELS)
Spillsaver™ EasyGlide™
shelves feature the
convenience of
easy cleaning
with a pullout
design to reach
items in the back. For ease of cleaning,
glass shelf may be removed by pulling to
full extension and lifting out of frame.
To remove shelf and frame, see
instructions for Spillsaver™ stationary
shelves.
REAR SHELF
EXTENSIONS
(SOME MODELS)
Rear shelf extensions help prevent
articles from falling off the back of the
shelf.
To remove and install shelf extension:
To remove,
pull extension
straight up
from rear of
shelf.
To install, insert posts of the shelf
extension into holes in the shelf frame.
Door storage
DAIRY CENTER
The dairy center
provides convenient
storage for items
such as butter,
yogurt, cheese, etc.
This compartment is an adjustable
feature located in the door. It can be
moved to several different locations to
accommodate storage needs.
To remove, open dairy door, pull
upward and tilt out.
To install, reverse above procedure.
DOOR BUCKETS
Door buckets adjust to meet
individual storage needs.
To remove, slide
bucket up and
pull straight
out.
To install, reverse above procedure.
DOOR RETAINER
Door retainers remove for easy cleaning.
To remove, slide retainer up and pull
straight out.
To install, reverse above procedure.
13
Climate-controlled
drawers
HUMIDITY-CONTROLLED
CRISPER DRAWERS
The crisper drawer keeps produce fresh
longer by providing an environment with
adjustable humidity.
Controls
The crisper
controls
regulate
the amount
of humidity in the crisper drawer. Use the
low setting for produce with outer skins.
Use the high setting for leafy produce.
To remove and install crisper drawers:
To remove
drawer, pull
drawer out to
full exten-
sion. Tilt up
front of drawer and pull straight out.
To install, insert drawer into frame rails
and push back into place.
TEMPERATURE-
CONTROLLED DRAWER
Chef's Pantry™
The Chef's Pantry™ system provides a
drawer with a variable temperature
control that keeps the compartment up to
F (3° C) colder than refrigerator
temperature. This drawer can be used for
large party trays, deli items, or
beverages.
Control
The Chef's Pantry™
control regulates the air
temperature in the
drawer. Set control level
to cold to provide normal refrigerator tem-
perature. Use the coldest setting for
meats or other deli items.
NOTE: Cold air directed to the Chef's
Pantry™ can decrease refrigerator tem-
perature. Refrigerator control may need
to be adjusted.
Accessories
GRIP PADS
(SOME MODELS)
The Grip Pads pre-
vents objects from sliding in
the door bucket. Grip Pads are remov-
able and are top-rack dishwasher safe for
easy cleaning.
WINE TRIVET/CAN RACK
(SOME MODELS)
The Wine
Trivet/Can Rack
accessory fits in
the bottom of most
drawer assemblies.
Beer bottles can be laid crosswise, or a
single bottle may be laid in the center
depression. Cans may also be stored
horizontally.
PANTRY DIVIDER
(SOME MODELS)
The pantry divider is used
to organize the
Chef's Pantry™
into sections.
To remove and replace divider:
To remove, raise front of divider to
unhook divider from rear wall of
pantry, and pull out.
To install, hook back of divider over
rear wall of pantry and lower into
place.
NOTE: For easiest removal and replace-
ment, remove pantry. If removal is not
possible, pull drawer open to its fullest
extension.
To remove and install pantry:
To remove draw-
er, lift lid and pull
drawer out to full
extension. Tilt up
front of pantry and pull straight out.
To install, push metal
glide rails to the back
of the unit. Place draw-
er onto rails and slide
drawer back until it falls into place.
HOW DO I REMOVE THE
GLASS AND CRISPER
FRAME IF I WANT TO
CLEAN IT?
1. Remove the drawers as instructed at
left.
2. Place hand beneath frame to push up
glass from underneath. Lift glass out.
3. Lift frame from refrigerator liner rails.
4. To install, repeat above instructions in
reverse order.
WHAT CAN I DO TO
PROLONG THE LIFE
OF MY PRODUCE?
Please observe the following rules when
storing produce in humidity-controlled
crisper drawers:
DO NOT wash produce before placing
in crispers. Any additional moisture
added to the drawers may cause pro-
duce to prematurely spoil.
DO NOT line crispers with paper
towels. Towels will retain moisture.
DO NOT place leafy vegetables in the
temperature-controlled drawer. Colder
temperatures will damage leafy produce.
Follow control instructions carefully.
Not setting controls correctly may
damage produce.
See chart below for assistance with
humidity drawer controls:
LOW cauliflower apples
corn oranges
zucchini • grapes
cucumbers
HIGH lettuce asparagus
spinach • cabbage
celery broccoli
fresh sprouts fresh herbs
14
Freezer features
Primary features
AUTOMATIC ICE MAKER
(SOME MODELS)
Using Ice Maker for the First Time
1. Confirm ice bin is in
place and ice maker
arm is down.
2. After freezer section reaches between
to 2° F (-18° to -17° C), ice maker
fills with water and begins operating.
3. Allow approximately 24 hours after
installation to receive first harvest of
ice.
4. Discard ice created within first 12
hours of operation to verify system is
flushed of impurities.
Operating Instructions
1. Confirm ice bin is in place and ice
maker arm is down.
2. After freezer section reaches 0° to 2° F
(-18° to -17° C), ice maker fills with
water and begins operating. You will
have a complete harvest of ice
approximately every 3 hours.
3. Stop ice production
by raising ice maker
arm until click is
heard.
4. Ice maker will remain in the off posi-
tion until arm is pushed down.
To avoid property damage, observe
the following:
Do not force ice maker arm down
or up.
Do not place or store anything in
ice storage bin.
CAUTION
To prevent accidental child entrap-
ment or suffocation risk, DO NOT
remove the divider in the top freezer
basket.
DANGER
Drawers
PULLOUT DRAWER
BASKETS (SOME MODELS)
(Door assembly of drawer removed from
illustration for visual clarity)
To remove and replace top basket:
Remove basket by pulling basket out
to its full extension and lift out.
Replace basket by sliding into upper
molded railing.
To remove and replace bottom basket:
Remove basket by lifting basket from
rail guides.
Replace basket by placing into rail
guides.
Accessories
LOWER BASKET DIVIDER
(SOME MODELS)
The lower basket divider allows the
option to organize the basket area into
sections.
To remove and replace divider:
To remove, pull divider straight up.
To install, hook top corners of divider
over top horizontal basket rungs.
15
Hints and Care
PART DO
Use 4 tablespoons of baking soda dissolved in 1 quart (1 liter)
warm soapy water.
Rinse surfaces with clean warm water and dry immediately to
avoid water spots.
Use warm, soapy water and a soft, clean cloth or sponge.
Rinse surfaces with clean warm water and dry immediately to
avoid water spots.
Use a vacuum cleaner hose nozzle.
Use a vacuum cleaner hose nozzle with brush attachment.
Follow removal and installation instructions from appropriate
feature section.
Allow items to adjust to room temperature.
Dilute mild detergent and use a soft clean cloth or sponge for
cleaning.
Use a plastic bristle brush to get into crevices.
Rinse surfaces with clean warm water.
Dry glass and clear items immediately to avoid spots.
DO NOT USE
Abrasive or harsh cleaners
Ammonia
Chlorine bleach
Concentrated detergents or
solvents
Metal or plastic-textured
scouring pads
Abrasive or harsh cleaners
Ammonia
Chlorine bleach
Concentrated detergents or
solvents
Metal or plastic-textured
scouring pads
Vinegar-based products
Citrus-based cleaners
Abrasive or harsh cleaners
Metal or plastic-textured
scouring pads
A dishwasher
Textured Doors
and Exterior
Cabinet Interior
Stainless Steel Doors
and Exterior
IMPORTANT: Damage
to stainless steel finish
due to improper use of
cleaning products or
non-recommended
products is not covered
under this product’s
warranty.
Door Gaskets
Condenser Coil
Remove base grille to
access
Condenser Fan Outlet
Grille
See back of refrigerator
Accessories Shelves,
buckets, drawers, etc.
To avoid personal injury or property damage, observe the following:
Read and follow manufacturer’s directions for all cleaning products.
DO NOT place buckets, shelves or accessories in dishwasher. Cracking or warp-
ing of accessories may result.
CAUTION
To avoid electrical shock which can
cause severe personal injury or death,
disconnect power to refrigerator
before cleaning. After cleaning, con-
nect power.
WARNING
How to clean your unit
16
What cleaners does
Amana recommend for my
stainless steel product?
Amana has a cleaner available for pur-
chase (Part # 31960801) through our
Consumer Affairs division.
For this, or a list of other recommended
cleaning products, please contact us at
Amana Consumer Affairs using the infor-
mation on the cover of your Owner's
Manual.
Removing odors from
refrigerator
1. Remove all food.
2. Disconnect refrigerator.
3. Clean the following items using the
appropriate instructions in the Care
and Cleaning table.
–Walls, floor and ceiling of cabinet
interior
Drawers, shelves and gaskets
according to the instructions in this
section.
4. Pay special attention to clean all
crevices by completing the following
steps.
Dilute mild detergent and brush
solution into crevices using a plas-
tic bristle brush.
Let stand for 5 minutes.
Rinse surfaces with warm water.
Dry surfaces with a soft, clean
cloth.
5. Wash and dry all bottles, containers
and jars. Discard spoiled or expired
items.
6. Wrap or store odor-causing foods in
tightly sealed containers to prevent
reoccurring odors.
7. Connect power to refrigerator and
return food to unit.
8. After 24 hours, check if odor has been
eliminated.
If odor is still present:
1. Remove drawers and place on top
shelf of refrigerator.
To avoid personal injury or property
damage, observe the following:
Allow light bulb to cool.
Wear gloves when replacing light
bulb.
CAUTION
To avoid electrical shock which can
cause severe personal injury or death,
disconnect power to refrigerator
before replacing light bulb. After
replacing light bulb, connect power.
WARNING
2. Pack refrigerator and freezer sections
– including doors – with crumpled
sheets of black and white newspaper.
3. Place charcoal briquettes randomly on
crumpled newspaper in both freezer
and refrigerator compartments.
4. Close doors and let stand 24-48
hours.
Energy saving ideas
When placing refrigerator into final
position, allow for
1
Ú2" clearance around
the top and sides of the unit to supply
ample ventilation for optimum energy
efficiency.
Avoid overcrowding refrigerator
shelves. This reduces air circulation
around food and causes refrigerator to
run longer.
Avoid adding too much warm food to
unit at one time. This overloads com-
partments and slows rate of cooling.
Do not use aluminum foil, wax paper,
or paper toweling as shelf liners. This
decreases air flow and causes unit to
run less efficiently.
A freezer that is
2
Ú3
full runs most effi-
ciently.
Locate refrigerator in coolest part of
room. Avoid areas of direct sunlight, or
near heating ducts, registers or other
heat producing appliances. If this is
not possible, isolate exterior by using
a section of cabinet or an added layer
of insulation.
Refer to Owner's Manual section on
temperature controls for recommend-
ed control settings.
Clean door gaskets every three
months according to Owner's Manual
cleaning instructions. This will assure
that door seals properly and unit runs
efficiently.
Take time to organize items in refriger-
ator to reduce time that door is open.
Be sure your doors are closing
securely by leveling unit as instructed
in your Owner's Manual.
Clean condenser coils as indicated in
the Owner’s Manual every 3 months.
This will increase energy efficiency
and cooling performance.
Remove and replace
light bulbs
Fresh Food Section
1. Slide shield toward
back of compartment
to release from light
assembly.
2. Remove light bulbs.
3. Replace with appliance bulbs no
greater than 40 watts.
4. Replace light bulb
cover by inserting
tabs on light shield
into liner holes on
each side of light
assembly. Slide shield toward front of
unit until it locks into place. DO NOT
force shield beyond locking point.
Doing so may damage light shield.
Freezer
1. Pinch rear tabs on
light cover and pull
straight down.
2. Remove light bulb.
3. Replace bulb with appliance bulb no
greater than 40 watts.
4. Insert front tabs of light cover into
freezer liner and snap rear portion
over light assembly until rear tabs
engage.
A
B
Hints and care,
cont.
17
Trouble shooting
Today’s refrigerators have new features and are more energy efficient. Foam insulation is very energy efficient and has excellent insu-
lating capabilities, however, foam insulation is not as sound absorbent. As a result, certain sounds may be unfamiliar. In time, these
sounds will become familiar. Please refer to this information before calling service.
B
J
G
A
F
C
I
E
K
D
H
SOLUTION
Normal operation
Normal operation
Normal operation
Normal operation
Normal operation
Normal operation
See Installation Instructions for details on how to level your
unit.
Normal operation
Stop sound by raising ice maker arm to ‘off’ position. See
Automatic Ice Maker section in your Owner’s Manual for
details.
Normal operation
Normal operation
POSSIBLE CAUSE
Freezer control (A) clicks when
starting or stopping compressor.
Defrost timer (B) sounds like an
electric clock and snaps in and
out of defrost cycle.
Freezer fan (C) and condenser
fan (D) make this noise while
operating.
Evaporator (E) and heat
exchanger (F) refrigerant makes
this noise when flowing.
Ice cubes from ice maker (select
models) drop into ice bucket (G).
Compressor (H) makes a
pulsating sound while running.
Refrigerator is not level.
Ice maker water valve (I)
hookup (select models) buzzes
when ice maker fills with water.
Ice maker (J) is in the ‘on’ posi-
tion without water connection.
Compressor (H) can make a high-
pitched hum while operating.
Defrost heater (K) hisses, sizzles
or pops when operational.
TOPIC
Clicking
Air rushing or whirring
Gurgling or boiling
sound
Thumping
Vibrating noise
Buzzing
Humming
Hissing or
popping
18
PROBLEM POSSIBLE CAUSES WHAT TO DO
Freezer control and lights Refrigerator is in defrost mode. Normal operation. Wait 40 minutes to see if refrigerator restarts.
are on, but compressor
is not operating
Crisper drawer Control settings are too low. See section on Crisper drawer to adjust controls.
temperature is too warm
Freezer controls are set too low. See controls section in Owner’s Manual on how to adjust your
controls.
Drawer is improperly positioned. See section on Crisper drawer to verify drawer positioning.
Refrigerator does not Refrigerator is not plugged in. Plug in unit.
operate
Freezer control is not on. See controls section in Owner’s Manual.
Fuse is blown, or circuit breaker needs to be Replace any blown fuses. Check circuit breaker and reset, if.
reset. necessary.
Power outage has occurred. Call local power company listing to report outage.
Refrigerator still won’t Unit is malfunctioning. Unplug refrigerator and transfer food to another unit. If another
operate unit is not available, place dry ice in freezer section to preserve
food. Warranty does not cover food loss.
Contact service for assistance.
Food temperature Condenser coils are dirty. Clean according to your Owner’s Manual.
is too cold
Refrigerator or freezer controls are set too high. See controls section in Owner’s Manual on how to adjust controls.
Food temperature Door is not closing properly. Refrigerator is not level. See How to Level Your Refrigerator
is too warm for details on how to level your unit.
Check gaskets for proper seal. Clean, if necessary, according to
cleaning instructions in Owner’s Manual.
Check for internal obstructions that are keeping door from closing
properly (i.e. improperly closed drawers, ice buckets, oversized
or improperly stored containers or foodstuffs, etc.)
Controls need to be adjusted. See the controls section in Owner’s Manual for assistance on
how to adjust your controls.
Condenser coils are dirty. Clean according to cleaning instructions in Owner’s Manual.
Rear air grille is blocked. Check the positioning of food items in refrigerator to make sure
grille is not blocked. Rear air grilles are located under crisper
drawers.
Door has been opened frequently, or has been Reduce time door is open. Organize food items efficiently to
opened for long periods of time. assure door is open for as short a time as possible.
Food has recently been added. Allow time for recently added food to reach refrigerator or freezer
temperature.
Refrigerator has an odor Compartment is dirty or has odor-causing food. Refer to Care and Cleaning in Owner’s Manual for odor removal
instructions.
Water droplets form on Check gaskets for proper seal. Clean, if necessary, according to cleaning instructions in
outside of refrigerator Owner’s Manual.
Humidity levels are high. Normal during times of high humidity.
Controls require adjustment. See the controls section in Owner’s Manual for assistance on
how to adjust your controls.
Water droplets form on Humidity levels are high or door has been See the controls section in Owner’s Manual for assistance on
inside of refrigerator been opened frequently. how to adjust your controls.
Check gaskets for proper seal. Reduce time door is open. Organize food items efficiently to
assure door is open for as short a time as possible.
Clean, if necessary, according to cleaning instructions in
Owner’s Manual.
Refrigerator or ice maker Normal operation. Refer to noise section of Normal Operating Sounds guide in
makes unfamiliar sounds Owner’s Manual.
or seems too loud
Operation
Trouble shooting,
cont.
19
PROBLEM POSSIBLE CAUSES WHAT TO DO
Crisper drawers do not Contents of drawer, or positioning of items Reposition food items and containers to avoid interference with
close freely in the surrounding compartment could be the drawers.
obstructing drawer.
Drawer is not in proper position. See Crisper drawer section for proper placement.
Refrigerator is not level. See How to Level Your Refrigerator for details on how to level
your unit.
Drawer channels are dirty or need treatment. Clean drawer channels with warm, soapy water. Rinse and dry
thoroughly.
Apply a thin layer of petroleum jelly to drawer channels.
Refrigerator runs too Doors have been opened frequently or for Reduce time door is open. Organize food items efficiently to
frequently long periods of time. assure door is open for as short a time as possible.
Allow interior environment to adjust for period the door has
been opened.
Humidity or heat in surrounding area is high. Normal operation.
Food has recently been added. Allow time for recently added food to reach refrigerator or
freezer temperature.
Unit is exposed to heat by environment or Evaluate your unit’s environment. Unit may need to be moved to
by appliances nearby. run more efficiently.
Condenser coils are dirty. Clean according to cleaning instructions in your Owner’s Manual.
Controls need to be adjusted. See controls section in your Owner’s Manual for assistance
on how to adjust your controls.
Door is not closing properly. Refrigerator is not level. See How to Level Your Refrigerator
for details on how to level your unit.
Check gaskets for proper seal. Clean, if necessary, according
to cleaning instructions in Owner’s Manual.
Check for internal obstructions that are keeping door from closing
properly (i.e. improperly closed drawers, ice buckets, oversized
or improperly stored containers or foodstuffs, etc.)
PROBLEM POSSIBLE CAUSES WHAT TO DO
Unit is leaking water Plastic tubing was used to complete water The manufacturer recommends using copper tubing for installation.
connection. Plastic is less durable and can cause leakage. The manufac-
turer is not responsible for property damage due to
improper installation or water connection.
Improper water valve was installed. Check water connection procedure in your “Installing Your
Refrigerator.” Self-piercing and
3
Ú
16” saddle valves cause low water
pressure and may clog the line over time. The manufacturer is
not responsible for property damage due to improper
installation or water connection.
Ice forms in inlet tube to Water pressure is low. Water pressure must be between 20 to 100 pounds per square
ice maker inch to function properly. A minimum pressure of 35 pounds per
square inch is recommended for units with water filters.
Freezer temperature is too high. See controls section in chapter called Installing Your Refrigerator
on how to adjust your controls. Freezer is recommended to be
between 0 to 2° F (-18 to –17° C).
Water flow is slower than Water pressure is low. Water pressure must be between 20 to 100 pounds per square
normal inch to function properly. A minimum pressure of 35 pounds per
square inch is recommended for units with water filters.
Improper water valve was installed. Check water connection procedure in your “Installing Your
Refrigerator.” Self-piercing and
3
Ú16” saddle valves cause low water
pressure and may clog the line over time. The manufacturer is
not responsible for property damage due to improper
installation or water connection.
Ice
20
Water filter data
GENERAL USE
CONDITIONS
Read this Performance Data Sheet and
compare the capabilities of this unit with
your actual water treatment needs.
DO NOT use this product where water
is microbiologically unsafe or of
unknown quality without adequate
disinfection before or after the sys-
tem. System certified for cyst reduc-
tion may be used on disinfected water
that may contain filterable cysts.
Use only with cold water supply.
Check for compliance with the state
and local laws and regulations.
The retractable water filtration system
uses a WF50 replacement cartridge.
Timely replacement of filter cartridge is
essential for performance satisfaction
from this filtration system. Please refer to
the applicable section in this owner’s
manual for general operation, mainte-
nance requirements and troubleshooting.
This system has been tested according to
ANSI/NSF 42 and 53 for reduction of the
substances listed below. The concentra-
tion of the indicated substances in water
entering the system was reduced to a
concentration less than or equal to the
permissible limit for water leaving the sys-
tem, as specified in ANSI/NSF 42 and 53.
*Tested using a flow rate of 0.75 GPM (2.83 L/min.) and a maximum pressure of 120 psi (827 kPa) under
standard laboratory conditions, however, actual performance may vary. Health Claim Performance test-
ed and certified by NSF International
** Particle size range classification of test. Particles used were 0.5 –1 microns.
Influent Challenge Effluent Average % Maximum Min. Required Inlet
Substance Concentration Average Reduction Effluent Reduction pH
Lead 0.15 mg/L +/- 10% 0.001 mg/L 99.33% 0.001 mg/L 0.010 mg/L 6.5
Lead 0.15 mg/L +/- 10% 0.002 mg/L 98.66% 0.003 mg/L 0.010 mg/L 8.5
Cyst Minimum 50,000/L 1count/mL 99.99% 3 count/mL > 99.95% NA
Turbidity 11+/-1 NTU 0.12 NTU 98.98% 0.18 NTU 0.5 NTU NA
Lindane 0.002 mg/L +/- 10% 0.00005 mg/L 97.62% 0.00005 mg/L 0.00002 mg/L NA
Atrazine 0.009 mg/L +/- 10% 0.0002 mg/L 97.93% 0.0006 mg/L 0.003 mg/L NA
Chlorine 2.0 mg/L +/- 10% 0.09 mg/L 95.26% 0.17 mg/L 75% NA
Particulate** at least 10,000 900 count/mL 99.68% 2400 count/mL 85% NA
particles/mL
2,4-D 0.210 mg/L +/- 10% 45.45 ug/L 84.42% 100 ug/L 0.0017 mg/L NA
Asbestos
10
7
to 10
8
fibers/L; fibers greater
0.16 MFL/mL 99.96% 0.16 MFL/mL 99% NA
than 10 micometers in length
PERFORMANCE DATA
SYSTEM SPECIFICATION AND PERFORMANCE DATA
SHEET REFRIGERATOR WATER FILTER CARTRIDGE
MODEL WF50
Specifications
Service Flow Rate (maximum) ...............................................0.75 GPM (2.83 L/min)
Rated Service Life WF50-NI300 (maximum) .........................300 gallons/1135 liters
Rated Service Life WF50-WI500 (maximum) ........................500 gallons/1892 liters
Maximum Operating Temperature..........................................100° F/38° C
Minimum Operating Temperature...........................................33° F/1° C
Minimum Pressure Requirement............................................35 psi/138 kPa
Maximum Operating Pressure ...............................................120 psi/827 kPa
1000 Apollo Road
Eagan, Minnesota U.S.A.
EPA EST #35917-MN-1
Standard No. 53: Health Effects
Chemical Reduction Unit
Lead, Atrazine, Lindane and 2, 4-D Reduction
Mechanical Filtration Unit
Cyst, Turbidity and Asbestos Reduction
Te sted and certified by NSF International against ANSI/NSF Standards 42 and 53 in
models WI500 and NI300 for the reduction of:
Standard No. 42: Aesthetic Effects
Taste and Odor Reduction
Chlorine Reduction
Mechanical Filtration Unit
Particulate Reduction Class 1
21
State of California
Department of Health Services
Water Treatment Device
Certificate Number
01 - 1486
Date Issued: September 21, 2001
Date Revised: March 20, 2002
T
rademark/Model Designa
tion Replacement Elements Rated Capacity
WF50-WI500 WF50 500 gal
WF50-NI300 WF50 300 gal
WF50-KWI500 46 9005 500 gal
WF50-KNI300 46 9005 300 gal
OWF50-WI500 OWF51 500 gal
OWF50-NI300 OWF51 300 gal
Manufacturer: PentaPure Incorporated
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the
Health and Safety Code for the following health related contaminants:
Microbiolo
gical Contaminants and Turbidity
Inoganic/Radiological Contaminants
Cysts Asbesos
Lead
Org
anic Contaminants
Atrazine
Lindane
Rated Service Flow: 0.75
22
Amana
refrigerator warranty
Owner's responsibility
Provide proof of purchase (sales receipt).
Provide normal care and maintenance. Replace owner replaceable items
where directions appear in Owner's Manual.
Make product reasonably accessible for service.
Pay premium service costs for service outside technician's normal busi-
ness hours.
Pay for service calls related to product installation and usage.
Amana Appliances Factory Service
1-800-628-5782 inside USA
For more information, Amana Appliances Consumer Services
Amana Appliances
2800 220th Trail
Amana, Iowa 52204
1-800-843-0304 inside USA
1-866-587-2002 au Canada
www.amana.com
First Year
Amana will replace, free of charge, any part
which is defective due to workmanship or
materials.
Second through Fifth Year
Amana will replace free of charge, any sealed
system component (compressor, condenser,
evaporator, drier and interconnecting tubing)
and repair any food compartment liner
(exclusive of door liner) which is defective due
to workmanship or materials.
Warranty Limitations
Begins at date of original purchase.
Excludes original and replacement water or
air filter cartridges (if equipped with the fil-
tration system). Original and replacement
cartridges are warranted for 30 days, parts
only, against defects of material or work-
manship.
Service must be performed by an author-
ized Amana technician.
Damage due to shipping and handling is
not covered by this warranty.
Warranty Is Void If
Repairs resulting from the following:
Serial plate is defaced.
Product is used on a commercial, rental, or
leased basis.
Product has defect or damage due to prod-
uct accident, alteration, connection to an
improper electrical supply, fire, flood, light-
ning, or other conditions beyond the con-
trol of Amana.
Product is improperly installed or used.
IN NO EVENT SHALL AMANA BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
This warranty gives you specific legal rights,
and you may have others which vary from state
to state. For example, some states do not
allow the exclusion or limitation of incidental or
consequential damages, so this exclusion may
not apply to you.
Loading...
+ 50 hidden pages