Allied Telesis Converteon AT-CV5000- User Manual

Size:
5.66 Mb
Download

AT-CV5000Media Converter Chassis Installation Guide

Resetting the Line Cards and the Module in the Rear Expansion Slot

To reset the line cards and the module in the rear expansion slot, perform the following procedure:

1.Locate the RESET LINE/EXP button, which is recessed on the front panel of the LED interface card.

Note

This RESET LINE/EXP button located on the LED interface card allows you to reset the line cards in the front of the chassis and any module in the rear expansion slot. This button does not reset any management cards in the chassis.

2.Press the reset button with the tip of a pen or a non-conductivepointed object, as shown inFigure 55.

PS-A

PS-B

 

SCON LOTS REAR

 

OLE

 

FAN-A

F

 

AN-B

261

Figure 55. Resetting Converteon™ Line Cards/Rear Expansion Module

81

Chapter 3: Working with Line Cards and other Modules

Installing an AT-PWR14AC Power Supply

The AT-CV5000chassis is shipped with two slots in the rear designated for the power supplies, but without any power supplies installed. You must install at least one power supply in order to power on the chassis.

Caution

The AT-CV5000Media Converter chassis can contain two power supplies of the same type (AC or DC) or a combination of the two types with the same power ratings. Make sure not to mix power supplies with different power ratings in the same chassis.

For information on the power supply module, refer to the documentation that is shipped with the module.

Note

You can install an additional AT-PWR14AC power supply while the existing power supply is powered ON.

Note

The AT-PWR14AC power supply is shipped with four power cords, one each for North America, the UK, Europe, and Australia. Locate the correct power cord for your location before beginning this procedure.

To install the AT-PWR14AC power supply, perform the following procedure:

1.Remove the AT-PWR14AC power supply from its shipping package and store the package in a safe place.

Note

You must use the original package if you need to return the unit to

Allied Telesis.

2.Select the power supply slot in the AT-CV5000chassis where you want to install theAT-PWR14AC power supply.

3.Make sure that the power switch for that slot is in the OFF position.

4.Remove any slot cover that may be covering that slot.

82

AT-CV5000Media Converter Chassis Installation Guide

5.Slide the AT-PWR14power supply into the selected slot, as shown inFigure 56, until the module is flush with the front of the chassis.

A

 

A

 

 

 

 

 

100-2

 

 

 

 

 

WARNINGThis unit

 

 

 

 

 

reduce thme ight have

 

 

 

 

 

risk of elemctorircesthhoacnko, ndeispcoownneercint paulltp.Toower

 

 

 

VAC~

 

P

OWER

AT-

PW

R14

AT-

 

FAULT

 

 

 

POWER

PWR14

 

 

 

 

FAULT

 

 

 

 

 

1129

B AT-CV5FAN

PWR A

PWR B

Figure 56. Inserting the AT-PWR14AC Power Supply

6.Secure the AT-PWR14AC power supply to theAT-CV5000chassis by using a Phillips screwdriver to tighten the captive screws, as shown inFigure 57.

A CVFAN-AT

 

A

 

 

 

 

100100--240240

 

 

 

 

 

 

VAC~

WARNINGThis

 

 

 

 

 

risk

unit might

have

 

 

 

 

ser

of electric

than one p

 

 

 

vicing unit. shock,mored

 

 

 

 

 

isconnect all power input

 

 

 

 

 

 

ower inputs. To reduce

the

 

 

 

 

 

before

 

 

 

 

 

AT-

 

 

 

POWER

 

PWR1

4

 

FAULT

 

 

 

 

 

212

PWR A

POWER FAULT

AT-PWR14

VAC~

B

 

CV5FAN-AT

1129

PWR B

Figure 57. Securing the AT-PWR14AC Power Supply

For information about powering on an AC-poweredchassis and starting a management session, refer to“Powering On an AC Powered Chassis” on page 60.

83

Chapter 3: Working with Line Cards and other Modules

Installing an AT-PWR15DC Power Supply

The AT-CV5000chassis is shipped with two slots in the rear designated for the power supplies, but without any power supplies installed. You must install at least one power supply in order to power on the chassis.

Caution

The AT-CV5000Media Converter chassis can contain two power supplies of the same type (AC or DC) or a combination of the two types with the same power ratings. Make sure not to mix power supplies with different power ratings in the same chassis.

For information on the power supply module, refer to the documentation that is shipped with the module.

Note

You can install an additional AT-PWR15DC power supply while the existing power supply is powered ON.

To install an AT-PWR15DC power supply, perform the following procedure:

1.Remove the AT-PWR15DC power supply from its shipping package and store the package in a safe place.

Note

You must use the original package if you need to return the unit to

Allied Telesis.

2.Select the power supply slot in the AT-CV5000chassis where you want to install theAT-PWR15DC power supply.

3.Turn the power switch OFF.

4.Remove any slot cover that may be covering that slot.

84

AT-CV5000Media Converter Chassis Installation Guide

5.Slide the AT-PWR15DC power supply into the selected slot, as shown inFigure 58, until the module is flush with the front of the chassis.

A

A

P

OWER

AT-

PW

R1

5

 

F

 

 

1225

POWER FAULT

AT-PWR15

B

CV5FAN-AT

216

PWR A

PWR B

Figure 58. Inserting the AT-PWR15DC Power Supply

6.Secure the AT-PWR15module to theAT-CV5000chassis by using a Phillips screwdriver to tighten the captive screws, as shown inFigure 59.

A

40-60VDC

A

 

 

 

 

irWARNINGTnehpdisuutcusenbithtefmeoirrgieshksteohrfavveicleeinmcgtoruicrensitthh.oacnko,ndeispcoower input

 

 

 

AT-

nnect all p.Toower

ACFOORRNENSCETECRNTICTIORTANELD,IZINESDTADLCLPOWER

 

PWR1

AREA.

ONLY IN

POWER

 

5

 

FAULT

 

 

 

 

inreWARNINGThpdisuutcusenbthitefmeoirrgisehksteohrfavveiceleinmcgtrouicrensitthh. oacnko, ndeispcoownneercint paulltp.Toower

ACFOORRNENSCETECRNTITCIROTAENLD, IIZNAESRDTEADALC.L

 

AT-

 

 

POWER

PWR1

5

FAULT

 

 

 

B POONWLYERIN

B AT-CV5FAN

1227

220

PWR A

PWR B

Figure 59. Securing the AT-PWR15DC Power Supply

For information about powering on an DC-poweredchassis and starting a management session, refer to“Powering On a DC Powered Chassis” on page 64.

85

Chapter 3: Working with Line Cards and other Modules

Replacing an AT-CVFANModule

This section provides instructions for replacing an AT-CVFANfan module if one fails.

Caution

For normal operation, the chassis must have two operational fans.

Caution

The AT-CVFANmodules arefield-replaceable;however, they are nothot-swappable.Therefore, make sure to power OFF the chassis before installing the fan modules.

Caution

Be sure to observe all standard electrostatic discharge (ESD) precautions, such as wearing an antistatic wrist strap, to avoid damaging the device. A fan module can be damaged by static electricity.

Warning

Remove jewelry before replacing the fan modules.

Warning

Watch your fingers when handling the fan modules.

Warning

To avoid electric shock, do not touch the inside of the fan slots.

To replace an AT-CVFANmodule, perform the following procedure:

1.Power OFF the chassis.

2.Using a Phillips screwdriver, loosen the captive screws at the top and bottom of the installed fan module faceplate.

86

A AN

AT-CV5000Media Converter Chassis Installation Guide

3.Pull the loosened screws to slide the fan out of the chassis, as shown in Figure 60 orFigure 61.

 

A

 

 

 

 

 

100-

 

 

 

 

 

240VAC~

WARNING

 

 

 

 

 

 

CVFAN-AT

 

This unit

 

 

 

 

reduce

might

 

 

 

 

 

the risk have

more than

 

 

 

of

 

 

 

 

 

electric shock,one power

 

 

 

 

 

disconnectinput. To

 

 

 

 

 

all power

204

Figure 60. Removing an AT-CVFANModule from Fan Slot A

 

 

A

 

 

-CV5PWRAC

100-24

0VAC

~

 

 

AT

B

 

 

100-24

0VAC

~

 

TWARhis unNINGthit me risighkt ohfaveelemctoricresthhoacnko, ndeispcoownneercint paulltp. Toower

 

 

reduce

 

 

AT-PWR14

POWE

R

T

 

FAUL

 

B

CVFAN-AT

205

Figure 61. Removing an AT-CVFANModule from Fan Slot B

4.While you wait for the fan to spin down, unpack the new AT-CVFANmodule from the shipping package and store the packaging material in a safe location.

Note

You must use the original shipping material if you need to return the fan module to Allied Telesis.

5.Carefully remove the fan module from the chassis.

6.To install a new fan, do one of the following:

Caution

Avoid touching the fan blades.

87

Chapter 3: Working with Line Cards and other Modules

a.To install a new fan in slot A, turn the fan so that the handle is on the left and slide the new fan module into the fan slot, as shown in Figure 62.

A

100240VAC~

btTWARNINGhehefiosrriusenksitoerfmveiilegcinhcttgrhicuanvseith.omck,oredtihscaonnonneecpt oalwl eprowinepruitn. pToutrseduce

AT-CVFAN

202

Figure 62. Inserting an AT-CVFANModule into Fan Slot A

b.To install a new fan in slot B, turn the fan so that the handle is on the right and slide the new fan module into the fan slot, as shown in Figure 63, until the front of the fan module is flush with the front of

the chassis.

A CV5FAN-

 

A

 

-CV5PWRAC

100-240

VAC~

 

AT

B

4 AT-PWR1

POWE

R

FAULT

 

B

100-240

VAC~

 

CVFAN-AT

203

Figure 63. Inserting an AT-CVFANModule into Fan Slot B

7.Tighten the two captive screws on the fan module, as shown in Figure 64 orFigure 65.

A CVFAN-AT

100240VAC~

WARNING

 

 

This unit

might

 

 

reduce

 

 

 

the risk have

more than

 

of

 

 

 

electric shock,one power

 

 

 

disconnectinput. To

 

 

 

all power

206

Figure 64. Tightening the Screws on the AT-CVFANModule in Slot A.

88

AT-CV5000Media Converter Chassis Installation Guide

A FAN

 

A

 

-CV5PWRAC

100-240

VAC~

 

AT

 

R

B

 

 

100-24

0VAC

~

 

 

TWAhisRNINGunthit me rigishkt ohfaveelemctroicresthhoacnko, ndeispcoownneercint paulltp. Toower

 

 

reduce

 

 

-PWR14

 

 

AT

 

 

POWE

R

T

 

FAUL

 

B AT-CVFAN

Figure 65. Tightening the Screws on the AT-CVFANModule in Slot B

To power on the chassis, proceed to the procedure described in “Powering On an AC Powered Chassis” on page 60 or“Powering On a DC Powered Chassis” on page 64.

When the connection is established, the appropriate fan LED (FAN-AorFAN-B)on the LED interface card should be green. If the LED is OFF, refer to“Troubleshooting” on page 95 for instructions.

89

Chapter 3: Working with Line Cards and other Modules

Installing a Blank Slot Cover

Installing an

AT-CV5PNL1

Blank Slot Cover

If any of the line card or expansion slots in the Converteon™ chassis is unoccupied, it must be covered with a blank slot cover, to keep dust from getting into the chassis and to maintain proper airflow, cooling, and ventilation throughout the chassis.

Note

Allied Telesis strongly recommends that a blank slot cover be inserted in any slot that does not contain a functioning line card or module.

The AT-CV5PNL1blank slot cover is designed to cover any unoccupied line card or management module slot in the Converteon™ Series chassis.

The AT-CV5000chassis is shipped with 18 line card slots covered with theAT-CV5PNL1blank slot covers.

To install an AT-CV5PNL1blank slot cover, perform the following procedure:

1.Select the line card you want to remove from the chassis.

2.Disconnect the cables from all the ports in the line card.

3.Cover the fiber optic port with the dust cap.

4.Remove the line card from the slot as described in “Removing a Converteon™ Line Card” on page 74.

5.Insert the AT-CV5PNL1slot cover into the slot you removed the line card from.

6.Align the back edge of the blank slot cover with the left and right alignment guides.

90