Allied Telesis Converteon AT-CV5000- User Manual
Size:
5.66 Mb
Download

Chapter 2: Installation

Selecting a Site for the Chassis

Observe the following requirements when choosing a site for the chassis:

If you plan to install the chassis in an equipment rack, check to be sure that the rack is safely secured and that it will not tip over. Devices in a rack should be installed starting at the bottom, with the heavier devices near the bottom of the rack.

The chassis is heavy and requires two people to install it. For the weight and dimensions of the chassis, see “Physical Specifications” on page 101.

If you are installing the chassis on a table, be sure that the table is level and secure.

The power outlet for the chassis should be located near the unit and should be easily accessible.

The site should provide easy access to the ports both on the front and the rear of the chassis. This arrangement will make it easy for you to connect and disconnect cables as well as to view the LEDs.

To allow proper cooling of the chassis, air flow around the unit and through its vents should be unrestricted. Allow 8 inches around the rear of the chassis for proper airflow.

Do not place objects on top of the chassis.

Do not expose the chassis to moisture or water.

Make sure that the site is a dust-freeenvironment.

Use dedicated power circuits or power conditioners to supply reliable electrical power to the device.

44

AT-CV5000Media Converter Chassis Installation Guide

Unpacking the Chassis

To unpack the chassis, perform the following procedure:

1. Remove all components from the shipping package.

Note

Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesis.

2.Make sure that the following components are included in the package. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance.

One AT-CV5000chassis

Two rack-mountingbrackets

Eight flathead Phillips rack-mountingbracket screws

Two power cord retaining clips

Two single ground lugs

One line card removal tool

Documentation CD

3.Place the AT-CV5000chassis on a level, secure surface.

45

Chapter 2: Installation

Installing the Power Cord Retaining Clip (AC Powered Chassis Only)

To install the power cord retaining clip on an AT-CV5000chassis with an

AT-PWR14AC power supply, perform the following procedure:

1. Locate the power cord retaining clip which is shown in Figure 14.

Figure 14. Power Cord Retaining Clip

2.Locate the retaining bracket on each side of the AC power connector on the rear of the chassis, as shown in Figure 15.

A

CVFAN-AT

Bracket

 

A

 

 

 

 

 

 

 

 

 

 

100-

 

 

 

 

 

 

 

 

 

 

 

 

 

240VAC~

WARNINGThis u

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

red

 

nit

 

have

 

 

 

 

 

 

 

 

 

uce thmighte

more

 

 

 

 

 

 

inputs

risk of

 

than o

 

 

 

 

 

 

 

before

 

 

elect

 

 

 

 

 

 

 

 

 

servicingric shock, ne power

input.

 

 

 

 

 

 

 

 

 

unit.

disco

 

To

 

 

 

 

 

 

 

 

 

 

 

nnect all

 

 

 

 

 

 

 

 

 

 

 

 

 

power

 

PO

 

 

 

 

 

 

 

 

 

 

 

 

 

WER

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

 

AULT

 

 

 

 

 

 

 

 

 

 

 

275

Figure 15. Power Cord Retaining Bracket

3.With the “u” of the clip facing up, press the sides of the clip toward the center and insert the short ends into the holes in the retaining bracket, as shown in Figure 16.

A CVFAN-AT

 

A

 

 

 

100-

 

 

 

 

240VAC~

WARNINGhis un

 

 

 

 

T

 

 

 

 

inrepduutsce itthme rigishkt have mo

re than

 

 

before

of elec

 

 

 

servicingtruicnsith. ocko, ndeispcoower input.

To

 

 

 

nnect all

 

 

 

 

power

 

PO

 

 

 

 

WER

 

 

 

 

F

 

 

 

 

AULT

 

 

 

276

Figure 16. Inserting the Retaining Clip into the Retaining Bracket

46

AT-CV5000Media Converter Chassis Installation Guide

4.Verify that the retaining clip is in the correct position, as shown in Figure 17.

A CVFAN-AT

 

A

 

 

 

100-

 

 

 

 

 

240VAC~

WARNINGis unit

 

 

 

 

Th

 

 

 

 

 

reduce

might

 

 

 

inputs

the risk have mo

re than

 

 

 

before

of elec

 

 

 

 

servicingtruicnsith. ocko, ndeispcoower input.

To

 

 

 

 

nnect all

 

 

 

 

 

power

 

PO

 

 

 

 

 

WER

 

 

 

 

F

 

 

 

 

 

AULT

 

 

 

 

277

Figure 17. Retaining Clip Properly Installed in the Bracket

47