Allied Telesis AT-SBXFAN12 User Manual

Size:
5.43 Mb
Download

SwitchBlade x3112

Access Edge Chassis Switch

AT-SBx3112Chassis

AT-SBx31GT24Line Card

AT-SBx31GT40Line Card

AT-SBx31GP24PoE Line Card

AT-SBx31GS24SFP Line Card

AT-SBx31GC40SFP BiDi Line Card

AT-SBx31XZ4XFP Line Card

AT-SBx31XS6SFP+ Line Card

AT-SBx31CFCCentral Fabric Control Card

AT-SBxPWRSYS1System Power Supply

AT-SBxPWRPOE1PoE Power Supply

AT-SBxFAN12Module

Installation Guide

613-001297Rev. F

Copyright 2013 Allied Telesis, Inc.

All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.

Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.

Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages.

Electrical Safety and Emissions Standards

This product meets the following standards.

U.S. Federal Communications Commission

Radiated Energy

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate this equipment.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003du Canada.

European Union Restriction of the Use of Certain Hazardous Substances

(RoHS) in Electrical and Electronic Equipment

This Allied Telesis RoHS-compliantproduct conforms to the European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls.

EMI/RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2,EN61000-3-3,CISPR Class A, VCCI Class A, AS/NZS Class A

Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Immunity: EN55024

Electrical Safety: EN60950-1(TUV), UL60950-1(CULUS), EN60825

Safety Agency Approvals: CULUS, TUV,C-TICK,CE

Laser Safety

EN60825

3

Translated Safety Statements

Important: Theindicates that a translation of the safety statement is available in a PDF document titled “Translated Safety Statements” on our web site athttp://www.alliedtelesis.com/support.

4

Contents

Preface ............................................................................................................................................................

15

Safety Symbols Used in this Document ...........................................................................................................

16

Contacting Allied Telesis ..................................................................................................................................

17

Chapter 1:Overview ......................................................................................................................................

19

Introduction.......................................................................................................................................................

20

AT-SBx3112 Chassis .......................................................................................................................................

23

Ethernet Line and Control Cards Slots.......................................................................................................

25

Power Supply Slots....................................................................................................................................

25

AT-SBx31GT24 Line Card................................................................................................................................

27

AT-SBx31GT40 Line Card................................................................................................................................

28

AT-SBx31GP24 PoE Line Card........................................................................................................................

29

AT-SBx31GS24 SFP Line Card .......................................................................................................................

30

AT-SBx31GC40 Line Card ...............................................................................................................................

31

AT-SBx31XZ4 XFP Line Card ..........................................................................................................................

33

AT-SBx31XS6 SFP+ Line Card........................................................................................................................

34

10/100/1000Base-T Twisted Pair Ports............................................................................................................

35

Connector Type..........................................................................................................................................

35

Speed.........................................................................................................................................................

35

Duplex Mode..............................................................................................................................................

35

Maximum Distance.....................................................................................................................................

36

Cable Requirements ..................................................................................................................................

36

Automatic MDIX Detection.........................................................................................................................

37

Straight-through or Crossover Cabling.......................................................................................................

37

Port Pinouts................................................................................................................................................

38

Power over Ethernet on the AT-SBx31GP24 Line Card...................................................................................

39

Powered Device Classes ...........................................................................................................................

39

Power Budgeting........................................................................................................................................

40

PoE Wiring .................................................................................................................................................

40

Port Numbers on the AT-SBx31GC40 Line Card .............................................................................................

42

Port LEDs on the Ethernet Line Cards .............................................................................................................

44

AT-SBx31GT24 Line Card .........................................................................................................................

44

AT-SBx31GT40 Line Card .........................................................................................................................

45

AT-SBx31GP24 Line Card.........................................................................................................................

46

AT-SBx31GS24 Line Card.........................................................................................................................

48

AT-SBx31GC40 Line Card.........................................................................................................................

49

AT-SBx31XZ4 Line Card............................................................................................................................

51

AT-SBx31XS6 Line Card ...........................................................................................................................

51

AT-SBx31CFC Central Fabric Controller Card.................................................................................................

53

SYS Status LEDs.......................................................................................................................................

54

SBx STATUS LEDs....................................................................................................................................

55

eco-friendly Button .....................................................................................................................................

56

Reset Button ..............................................................................................................................................

56

NET MGMT Port ........................................................................................................................................

58

NET MGMT LED........................................................................................................................................

60

5

Contents

 

Console (RS-232) Port ..............................................................................................................................

60

SD Card Slot..............................................................................................................................................

60

SD Status LED ..........................................................................................................................................

61

USB Port....................................................................................................................................................

61

Power Supplies ................................................................................................................................................

62

LEDs..........................................................................................................................................................

63

AT-SBxFAN12 Module.....................................................................................................................................

65

LED............................................................................................................................................................

65

Power Supply Interfaces (Opto-couplers) ........................................................................................................

66

LED............................................................................................................................................................

66

Module Names in the Management Software..................................................................................................

67

Management Software Releases for the Hardware Components....................................................................

68

Chapter 2:Safety Precautions and Site Preparation .................................................................................

69

Reviewing Safety Precautions .........................................................................................................................

70

Selecting a Site for the SwitchBlade x3112 .....................................................................................................

74

Chapter 3:Installing the Chassis in an Equipment Rack ..........................................................................

77

Required Tools and Material............................................................................................................................

78

Preparing the Equipment Rack ........................................................................................................................

79

Unpacking the AT-SBx3112 Chassis...............................................................................................................

82

Adjusting the Equipment Rack Brackets..........................................................................................................

84

Installing the AT-SBx3112 Chassis in the Equipment Rack.............................................................................

86

Removing the Shipping Brace .........................................................................................................................

89

Installing the Chassis Grounding Lug ..............................................................................................................

90

Chapter 4:Installing the Power Supplies ...................................................................................................

93

Protecting Against Electrostatic Discharge (ESD) ...........................................................................................

94

Installing the AT-SBxPWRSYS1 AC System Power Supply............................................................................

95

Installing the AT-SBxPWRPOE1 AC Power Supply ......................................................................................

101

Installing the AT-SBxPWRSYS1 DC Power Supply.......................................................................................

107

Chapter 5:Installing the AT-SBx31CFC Card and Ethernet Line Cards ................................................

113

Installing the AT-SBx31CFC Central Fabric Controller Card .........................................................................

114

Installing the Ethernet Line Cards..................................................................................................................

120

Installing the Blank Slot Covers .....................................................................................................................

124

Chapter 6:Installing the Transceivers and Cabling the Ports ................................................................

127

Guidelines to Cabling the AT-SBx31GP24, AT-SBx31GT24, and AT-SBx31GT40 Line Cards ....................

128

Connecting Cables to the AT-SBx31GT40 Line Card .............................................................................

129

Guidelines to Installing SFP, SFP+, CSFP, and XFP Transceivers...............................................................

131

Installing SFP Transceivers in the AT-SBx31GS24 Line Card ......................................................................

132

Installing SFP and CSFP Transceivers in the AT-SBx31GC40 Line Card.....................................................

136

Installing SFP+ Transceivers in the AT-SBx31XS6 Line Card.......................................................................

140

Installing AT-SP10TW Cables in the AT-SBx31XS6 Line Card.....................................................................

144

Installing XFP Transceivers in the AT-SBx31XZ4 Line Card.........................................................................

147

Cabling the NET MGMT Port on the AT-SBx31CFC Card.............................................................................

151

Chapter 7:Powering On the Chassis ........................................................................................................

153

Verifying the Installation.................................................................................................................................

154

Powering On the AT-SBxPWRSYS1 AC Power Supply ................................................................................

155

Powering on the AT-SBxPWRPOE1 AC Power Supply.................................................................................

158

Powering On the AT-SBxPWRSYS1 DC System Power Supply...................................................................

161

Choosing a Method for Attaching the Grounding Wire ............................................................................

163

Connecting the Grounding Wire with the Grounding Terminal ................................................................

163

Connecting the Grounding Wire with Bare Wire......................................................................................

166

Choosing a Method for Attaching the Power Wires.................................................................................

167

Connecting the DC Power Wires with the Straight Terminals .................................................................

168

6

 

SwitchBlade x3112 Installation Guide

Connecting the DC Power Wires with the Right Angle Terminals

............................................................175

Connecting Bare DC Power Wires...........................................................................................................

180

Monitoring the Initialization Process ...............................................................................................................

184

Using the LEDs to Monitor the Initialization Process ...............................................................................

185

Using the Console Port to Monitor the Initialization Process ...................................................................

186

Chapter 8:Verifying the Hardware Operations of the Chassis ...............................................................

189

Using the LEDs to Verify the Chassis.............................................................................................................

190

Using Local Management to Verify the Chassis.............................................................................................

192

Starting a Local Management Session ....................................................................................................

192

Entering the Management Software Commands .....................................................................................

193

Chapter 9:Troubleshooting .......................................................................................................................

197

AT-SBxPWRSYS1 and AT-SBxPWRPOE1 AC Power Supplies ...................................................................

198

AT-SBxPWRSYS1 DC Power Supply ............................................................................................................

199

Ethernet Line Cards........................................................................................................................................

201

Twisted Pair Ports ..........................................................................................................................................

203

Power Over Ethernet ......................................................................................................................................

205

Fiber Optic Transceivers ................................................................................................................................

207

AT-SBx31CFC Central Fabric Controller Card...............................................................................................

209

AT-SBxFAN12 Fan Module ............................................................................................................................

210

Local (Out-of-Band) Management Session ....................................................................................................

211

Power Supply Interfaces (Opto-couplers).......................................................................................................

212

Appendix A: Technical Specifications ......................................................................................................

213

Physical Specifications ...................................................................................................................................

213

Environmental Specifications .........................................................................................................................

215

Power Specifications ......................................................................................................................................

216

Safety and Electromagnetic Emissions Certifications ....................................................................................

219

Port Pinouts ....................................................................................................................................................

220

7

Contents

8

Figures

Figure 1: AT-SBx3112 Chassis .......................................................................................................................

20

Figure 2: Ethernet Line Cards and AT-SBx31CFC Central Fabric Controller Card.........................................

20

Figure 3: Ethernet Line Cards and AT-SBx31CFC Central Fabric Controller Card (Continued).....................

21

Figure 4: Power Supply Units ..........................................................................................................................

21

Figure 5: Fan Module ......................................................................................................................................

22

Figure 6: Front View of the AT-SBx3112 Chassis ...........................................................................................

23

Figure 7: Rear View of the AT-SBx3112 Chassis............................................................................................

24

Figure 8: AT-SBx3112 Chassis with Line Cards, Control Cards, and Power Supplies ...................................

24

Figure 9: Slots for the Ethernet Line and Control Cards..................................................................................

25

Figure 10: Power Supply Slots ........................................................................................................................

25

Figure 11: AT-SBx31GT24 Line Card .............................................................................................................

27

Figure 12: AT-SBx31GT40 Line Card .............................................................................................................

28

Figure 13: AT-SBx31GP24 PoE Line Card .....................................................................................................

29

Figure 14: AT-SBx31GS24 SFP Line Card .....................................................................................................

30

Figure 15: AT-SBx31GC40 Line Card .............................................................................................................

31

Figure 16: AT-SBx31XZ4 XFP Line Card........................................................................................................

33

Figure 17: AT-SBx31XS6 Line Card................................................................................................................

34

Figure 18: Port Numbers for Slots with CSFP Transceivers ...........................................................................

42

Figure 19: Port Numbers for Slots with Standard SFP Transceivers ..............................................................

43

Figure 20: Port LEDs on the AT-SBx31GT24 Line Card .................................................................................

44

Figure 21: Port LEDs on an RJ Point 5 Cable Connector for the AT-SBx31GT40 Line Card .........................

45

Figure 22: Link/Activity LED on an RJ Point 5 Cable Connector for the AT-SBx31GT40 Line Card...............

45

Figure 23: Port LEDs on the AT-SBx31GP24 PoE Line Card .........................................................................

46

Figure 24: Port LEDs on the AT-SBx31GS24 SFP Line Card.........................................................................

48

Figure 25: LEDs for the AT-SBx31GC40 Line Card ........................................................................................

49

Figure 26: LEDs for the AT-SBx31GC40 Line Card, with CSFP Transceivers ...............................................

49

Figure 27: LEDs for the AT-SBx31GC40 Line Card, with SFP Transceivers ..................................................

50

Figure 28: Transceiver Slot LEDs on the AT-SBx31XZ4 XFP Line Card ........................................................

51

Figure 29: SFP+ Slot LEDs on the AT-SBx31XS6 Line Card..........................................................................

51

Figure 30: AT-SBx31CFC Central Fabric Controller Card...............................................................................

54

Figure 31: AT-SBxFAN12 Module ...................................................................................................................

65

Figure 32: Power Supply Interfaces (Opto-couplers) ......................................................................................

66

Figure 33: 100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle................................................................

75

Figure 34: Reserving Vertical Rack Space......................................................................................................

80

Figure 35: Rack Mounting Hole Locations.......................................................................................................

81

Figure 36: AT-SBx3112 Chassis Items ...........................................................................................................

82

Figure 37: AT-SBx3112 Chassis Items (Continued)........................................................................................

83

Figure 38: Rack Mounting Bracket Locations..................................................................................................

85

Figure 39: Rack Bracket Locations for Reverse Position of Chassis ..............................................................

85

Figure 40: Lifting the AT-SBx3112 Chassis into the Equipment Rack ............................................................

87

Figure 41: Installing the Rack Mount Screws ..................................................................................................

88

Figure 42: Removing the Shipping Brace........................................................................................................

89

Figure 43: Stripping the Grounding Wire .........................................................................................................

90

Figure 44: Removing the Grounding Lug ........................................................................................................

90

Figure 45: Attaching the Grounding Wire to the Grounding Lug .....................................................................

91

9

List of Figures

 

Figure 46: Installing the Grounding Lug and Wire ...........................................................................................

91

Figure 47: ESD Socket and Wrist Strap...........................................................................................................

94

Figure 48: Power Supply Slots.........................................................................................................................

95

Figure 49: Removing the Blank Slot Cover from Power Supply Slot C............................................................

96

Figure 50: Items Included with the AT-SBxPWRSYS1 Power Supply Module ................................................

97

Figure 51: Verifying the AT-SBxPWRSYS1 AC Power Supply........................................................................

98

Figure 52: Raising the Handle on the AT-SBxPWRSYS1 AC Power Supply ..................................................

98

Figure 53: Inserting the AT-SBxPWRSYS1 AC Power Supply........................................................................

99

Figure 54: Lowering the Handle on the AT-SBxPWRSYS1 AC Power Supply..............................................

100

Figure 55: Power Supply Slots.......................................................................................................................

101

Figure 56: Removing the Blank Slot Cover from Power Supply Slot A..........................................................

102

Figure 57: Items Included with the AT-SBxPWRPOE1 Power Supply Module..............................................

103

Figure 58: Verifying the AT-SBxPWRPOE1 AC Power Supply .....................................................................

104

Figure 59: Raising the Handle on the AT-SBxPWRPOE1 AC Power Supply................................................

104

Figure 60: Inserting the AT-SBxPWRPOE1 AC Power Supply......................................................................

105

Figure 61: Locking the Handle on the AT-SBxPWRPOE1 AC Power Supply................................................

106

Figure 62: Power Supply Slots.......................................................................................................................

107

Figure 63: Removing the Blank Slot Cover from Power Supply Slot C..........................................................

108

Figure 64: Items Included with the AT-SBxPWRSYS1 DC Power Supply Module........................................

109

Figure 65: Loosening the Handle locking Screw on the AT-SBxPWRPOE1 DC Power Supply....................

110

Figure 66: Raising the Handle on the AT-SBxPWRPOE1 DC Power Supply................................................

110

Figure 67: Inserting the AT-SBxPWRSYS1 DC Power Supply......................................................................

111

Figure 68: Locking the Handle on the AT-SBxPWRSYS1 Power Supply......................................................

112

Figure 69: Slots 4 and 5 for the AT-SBx31CFC Card ....................................................................................

114

Figure 70: Items Included with the AT-SBx31CFC Central Fabric Controller Card .......................................

115

Figure 71: Opening the Locking Handles on the AT-SBx31CFC Central Fabric Controller Card..................

115

Figure 72: Removing the Battery Insulator ....................................................................................................

116

Figure 73: Aligning the AT-SBx31CFC Card in the Chassis Slot...................................................................

116

Figure 74: Inserting the AT-SBx31CFC Card in the Chassis Slot..................................................................

117

Figure 75: Closing the Locking Levers on the AT-SBx31CFC Central Fabric Controller Card ......................

118

Figure 76: Tightening the Thumb Screws on the AT-SBx31CFC Card..........................................................

119

Figure 77: Slots 0 to 3 and 6 to 11 for the Ethernet Line Cards.....................................................................

120

Figure 78: Aligning an Ethernet Line Card in a Chassis Slot .........................................................................

121

Figure 79: Inserting an Ethernet Line Card....................................................................................................

122

Figure 80: Tightening the Thumb Screws on an Ethernet Line Card.............................................................

123

Figure 81: Installing a Blank Slot Cover.........................................................................................................

124

Figure 82: Tightening the Thumbscrews on a Blank Slot Cover....................................................................

125

Figure 83: RJ Point 5 Cable Connector for AT-SBx31GT40 Line Card .........................................................

129

Figure 84: Connecting Cables to Ports on the AT-SBx31GT40 Line Card ....................................................

130

Figure 85: Removing the Dust Cover from an SFP Slot in the AT-SBx31GS24 Line Card ...........................

132

Figure 86: Handle on SFP Transceiver..........................................................................................................

133

Figure 87: Inserting the SFP Transceiver in the AT-SBx31GS24 Line Card .................................................

133

Figure 88: Removing the Dust Cover from the SFP Transceiver in the AT-SBx31GS24 Line Card..............

134

Figure 89: Attaching a Fiber Optic Cable to an SFP Transceiver in the AT-SBx31GS24 Line Card .............

135

Figure 90: Removing the Dust Cover from a Transceiver Slot.......................................................................

136

Figure 91: Labels on SFP and CSFP Transceivers .......................................................................................

137

Figure 92: Inserting an SFP or a CSFP Transceiver......................................................................................

137

Figure 93: Removing the Dust Cover from an SFP or a CSFP Transceiver..................................................

138

Figure 94: Attaching a Fiber Optic Cable.......................................................................................................

139

Figure 95: Removing a Dust Cover From an SFP+ Slot in the AT-SBx31XS6 Line Card .............................

140

Figure 96: Handle on SFP+ Transceiver........................................................................................................

141

Figure 97: Installing an SFP+ Transceiver in the AT-SBx31XS6 Line Card ..................................................

141

Figure 98: Removing the Dust Cover from an SFP+ Transceiver in the AT-SBx31XS6 Line Card ...............

142

Figure 99: Attaching a Fiber Optic Cable to an SFP+ Transceiver in the AT-SBx31XS6 Line Card .............

143

Figure 100: Removing the Dust Cover From an SFP+ Slot in the AT-SBx31XS6 Line Card ........................

144

10