Port Interface Card
Installation and Safety Guide
AT-AR020 PRI E1/T1 AT-AR021 (S) BRI-S/T AT-AR021 (U) BRI-U AT-AR022 ETH AT-AR023 SYN AT-AR024 ASYN4 AT-AR026 4ETH AT-AR027 VoIP-FXS
Port Interface Card
Installation and Safety Guide
AT-AR020 PRI E1/T1
AT-AR021(S) BRI-S/T
AT-AR021(U) BRI-U
AT-AR022 ETH
AT-AR023 SYN
AT-AR024 ASYN4
AT-AR026 4ETH
AT-AR027 VoIP-FXS
Download the complete document set from www.alliedtelesis.com/support/software
2 |
Port Interface Card |
Port Interface Card Installation and Safety Guide
Document Number 613-000601 Rev C.
© 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis, Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages.
Allied Telesis and AlliedWare are trademarks or registered trademarks in the United States and elsewhere of Allied Telesis, Inc. Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Microsoft and Visio are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Additional brands, names and products mentioned herein may be trademarks of their respective companies.
Installation and Safety Guide |
3 |
Port Interface Cards (PICs) are a cost effective and flexible mechanism for adding new or additional network interfaces to your switch or router.
This Installation and Safety Guide describes how to install the following PICs:
■AT-AR020 PRI E1/T1, a single ISDN Primary Rate E1/T1 interface
■AT-AR021(S) BRI-S/T, a single ISDN Basic Rate S/T interface
■AT-AR021(U) BRI-U, a single ISDN Basic Rate U interface
■AT-AR022 ETH, a dual Ethernet 10BASE-T/AUI port
■AT-AR023 SYN, a single 2Mbps synchronous interface
■AT-AR024 ASYN4, four asynchronous ports
■AT-AR026 4ETH, four Ethernet 10BASE-T ports
■AT-AR027 VoIP-FXS, two Foreign Exchange Voice over IP ports
You can download the complete documentation for Port Interface Cards from www.alliedtelesis.com/support/software. For more information about the documentation and other resources, see “Obtaining Documentation and Resources” on page 11.
You can install a PIC into a PIC bay on the base unit of your switch or router, or into a PIC bay on an AT-AR040 NSM (Network Service Module) installed in your switch or router.
The following table shows which PICs are appropriate for different expansion bays and models of switch and router.
This expansion bay ... |
Accepts ... |
|
|
PIC bays in the AR415S, AR440S, AR441S, |
All PICs. |
AR442S, AR725, and AR745 router |
|
|
|
PIC bays in the AR750S, AR750S-DP, and |
AT-AR020, AT-AR021, AT-AR023, |
AR770S router |
and AT-AR024. |
|
|
AT-AR040 NSM in the AR745 router, |
All PICs except AT-AR022 and |
Rapier 16fi and Rapier 24i switch |
AT-AR026. |
|
|
AT-AR040 NSM in the Rapier 48w switch |
AT-AR020, AT-AR021, and AT-AR024. |
|
|
The AT-AR021(S) V3 hardware revision, identified by the label “AR021v3” on the board, requires a switch or router running AlliedWare® Operating System version 2.9.1-13 or later.