Allied Telesis 613-50550-00 User Manual

Size:
468.86 Kb
Download

Specifications

Item

Specification

 

 

 

 

Dimensions (H x W x L)

29.21 x 43.85 x 243.22 mm

 

(1.15 x 1.71 x 9.57 in.)

 

 

Operating Temperature

0° C to 40° C

 

 

Storage Temperature

-20°C to 80° C

 

 

Relative Humidity

<85% non-condensing

 

 

Supply Voltage

+3.15 V - +3.45 V

 

 

Bit Rate

100 Mb/s - 2700 Mb/s

 

 

Optical Output Power

+1 dBm - +3 dBm

 

 

Receiver sensitivity (BER

-28dBm(OC-48)

<10^-10for OC rates, BER

-31dBm (GbE)

<10^-12for GbE)

-33dBm(OC-12)

 

-35dBm(OC-3)

 

 

Receiver Optical Overload

-7dBm

 

 

Electrical Safety and Emission Statement

This product meets the following standards.

U.S. Federal Communications Commission

Radiated Energy

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-CausingEquipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

RFI Emissions EN 55022 Class A

Warning

In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Immunity

EN 55024

Electrical Safety UL 1950 (CULUS), EN 60950 (TUV)

Laser Safety EN 60825 (Class 1)

Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. www.alliedtelesyn.com

AT-LX3811/xMulti-ServiceLine Card

Installation Guide

Overview

An AT-LX3811/xMulti-ServiceLine Card is designed for use in anAT-LX3800UMulti-ServiceTransport System. Each line card contains one optical SFP transceiver port. The line cards are hot swappable into and out of the system. Each line card can only be used in its dedicated slot.

 

 

AT-LX3

811/8

 

 

 

 

 

 

RDY

 

 

 

TRIB

TX

 

 

 

 

RX

 

SYNC

 

 

 

 

 

 

 

 

X

LINE

 

 

 

X

 

 

 

 

The line card models, their corresponding wavelengths, and their slot position in the AT-LX3800Usystem are listed in the following table.

 

 

 

Model

Wavelength

Slot Number

 

 

 

 

 

 

AT-LX3811/1

1470

1

 

 

 

AT-LX3811/2

1490

2

 

 

 

AT-LX3811/3

1510

3

 

 

 

AT-LX3811/4

1530

4

 

 

 

AT-LX3811/5

1550

5

 

 

 

AT-LX3811/6

1570

6

 

 

 

AT-LX3811/7

1590

7

 

 

 

AT-LX3811/8

1610

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Laser

 

 

Class 1 laser product.

Laser

Do not stare into the laser beam.

PN 613-50550-00Rev. A

Specifications

Item

Specification

 

 

 

 

Dimensions (H x W x L)

29.21 x 43.85 x 243.22 mm

 

(1.15 x 1.71 x 9.57 in.)

 

 

Operating Temperature

0° C to 40° C

 

 

Storage Temperature

-20°C to 80° C

 

 

Relative Humidity

<85% non-condensing

 

 

Supply Voltage

+3.15 V - +3.45 V

 

 

Bit Rate

100 Mb/s - 2700 Mb/s

 

 

Optical Output Power

+1 dBm - +3 dBm

 

 

Receiver sensitivity (BER

-28dBm(OC-48)

<10^-10for OC rates, BER

-31dBm (GbE)

<10^-12for GbE)

-33dBm(OC-12)

 

-35dBm(OC-3)

 

 

Receiver Optical Overload

-7dBm

 

 

Electrical Safety and Emission Statement

This product meets the following standards.

U.S. Federal Communications Commission

Radiated Energy

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-CausingEquipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

RFI Emissions

EN 55022 Class A

Warning

In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Immunity

EN 55024

 

Electrical Safety UL 1950 (CULUS), EN 60950 (TUV)

 

 

Laser Safety EN 60825

(Class 1)

Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. www.alliedtelesyn.com

AT-LX3811/xMulti-ServiceLine Card

Installation Guide

Overview

An AT-LX3811/xMulti-SerivceLine Card is designed for use in anAT-LX3800UMulti-ServiceTransport System. Each line card contains one optical SFP transceiver port. The line cards are hot swappable into and out of the system. Each line card can only be used in its dedicated slot.

 

 

AT-LX

 

 

 

3811/8

 

 

RDY

 

 

TRIB

TX

 

 

 

RX

SYNC

 

 

 

 

 

 

X

LINE

 

 

X

 

 

 

The line card models, their corresponding wavelengths, and their slot position in the AT-LX3800Usystem are listed in the following table.

Model

Wavelength

Slot Number

 

 

 

 

 

 

AT-LX3811/1

1470

1

 

 

 

AT-LX3811/2

1490

2

 

 

 

AT-LX3811/3

1510

3

 

 

 

AT-LX3811/4

1530

4

 

 

 

AT-LX3811/5

1550

5

 

 

 

AT-LX3811/6

1570

6

 

 

 

AT-LX3811/7

1590

7

 

 

 

AT-LX3811/8

1610

8

 

 

 

Laser

Class 1 laser product. Do not stare into the laser beam.

Laser

Do not stare into the laser beam.

PN 613-50550-00Rev. A

Related Documents

For details on the features and functions of your Allied Telesyn AT-LX3800UMulti-ServiceTransport System, refer to the following documents on our web site, www.alliedtelesyn.com:

AT-LX3800UMulti-ServiceTransport System Installation and Maintenance Guide

(part number 613-50549-00)

AT-S65Management Software User’s Guide

(part number 613-50604-00)

Verifying Package Contents

Make sure that the correct components are included in your package:

AT-LX3811/xMulti-ServiceLine Card

This installation guide

Warranty card

If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.

Installing the Line Card

To install an AT-LX3811/xLine Card, perform the following procedure:

1.Remove the AT-LX3811/xline card from its shipping package and store the package in a safe place. You must use the original package if you need to return the unit to Allied Telesyn.

2.Select the slot in the AT-LX3800Uchassis that corresponds to the number of the line card you want to install.

3.Remove any AT-LX3801Blank Slot Cover from the slot.

Keep the blank slot cover in a safe area in case you remove the line card. The blank slot cover protects the fiber optic connectors on the backplane from becoming dirty, and helps maintain proper air flow through the chassis.

4.Remove the dust caps from the fiber optic connectors at the back of the card and save for future use.

173

5.Locate the left and right alignment guides in the slot.

SYNC

RDY

TX LINE

TX

RX

TRIB

RX

138

Alignment Guides

6.Align the back edge of the line card with the left and right alignment guides.

7.Slide the card into the slot that corresponds to the line card number, until the faceplate is flush with the front.

2 X3811/2

 

 

 

3

 

 

 

 

AT-

 

SYNC

 

 

LX3811/3

 

 

LINE

RDY

 

4

RX

TRIB

TX

AT-

LX3811/4

 

 

 

RX

 

 

 

6

 

 

AT-

 

 

LX3811/6

 

RDY

 

TRIB

TX

 

 

RX

SYNC

LINE

RD

TRIB

T

 

R

 

 

AT

 

 

RDY

 

139

 

 

 

TRIB

TX

 

 

 

RX

SYNC

 

 

 

 

 

 

X

LINE

 

 

X

 

 

 

8.Use a Phillips head screwdriver to tighten the captive

screws on the line card.

2 X3811/2

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

AT-

 

 

 

 

 

 

 

 

SYNC

 

 

LX3811/3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

LINE

RDY

 

 

 

 

 

 

 

 

RX

TRIB

TX

 

 

 

AT-

LX3811/4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RX

SYNC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

TX

LINE

RDY

 

 

 

 

 

 

 

 

RX

 

 

 

 

 

 

 

 

 

 

TRIB

TX

 

 

 

 

AT-

LX3811/5

 

 

 

 

 

RX

 

SYNC

 

 

 

 

 

 

 

 

 

 

RX

LINE

RDY

 

 

 

 

 

 

 

 

 

TRIB

TX

 

 

 

 

 

 

 

 

 

 

 

RX

 

SYNC

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

AT-

 

 

LX3811/6

LINE

RDY

 

TRIB

TX

 

 

RX

SYNC

 

 

LINE

RD

TRIB

T

 

R

140

Note

Always tighten the captive screws to secure the line card to the chassis. This helps ensure that the fiber optic connectors at the back of the line card are securely connected to the backplane.

9.Repeat this procedure to install additional line cards.

For information about the line card LEDs, installing SFPs in the line card, and connecting fiber optic cables, refer to the

AT-LX3800UMulti-ServiceTransport System Installation and Maintenance Guide.

Related Documents

For details on the features and functions of your Allied Telesyn AT-LX3800UMulti-ServiceTransport System, refer to the following documents on our web site,

www.alliedtelesyn.com:

AT-LX3800UMulti-ServiceTransport System Installation and Maintenance Guide

(part number 613-50549-00)

AT-S65Management Software User’s Guide

(part number 613-50604-00)

Verifying Package Contents

Make sure that the correct components are included in your package:

AT-LX3811/xMulti-ServiceLine Card

This installation guide

Warranty card

If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.

Installing the Line Card

To install an AT-LX3811/xLine Card, perform the following procedure:

1.Remove the AT-LX3811/xline card from its shipping package and store the package in a safe place. You must use the original package if you need to return the unit to Allied Telesyn.

2.Select the slot in the AT-LX3800Uchassis that corresponds to the number of the line card you want to install.

3.Remove any AT-LX3801Blank Slot Cover from the slot.

Keep the blank slot cover in a safe area in case you remove the line card. The blank slot cover protects the fiber optic connectors on the backplane from becoming dirty, and helps maintain proper air flow through the chassis.

4.Remove the dust caps from the fiber optic connectors at the back of the card and save for future use.

173

5.Locate the left and right alignment guides in the slot.

SYNC

RDY

TX LINE

TX

RX

TRIB

RX

138

Alignment Guides

6.Align the back edge of the line card with the left and right alignment guides.

7.Slide the card into the slot that corresponds to the line card number, until the faceplate is flush with the front.

2 X3811/2

 

 

 

3

 

 

 

 

AT-

 

SYNC

 

 

LX3811/3

 

 

LINE

RDY

 

4

RX

TRIB

TX

AT-

LX3811/4

 

 

 

RX

 

 

 

6

 

 

AT-

 

 

LX3811/6

 

RDY

 

TRIB

TX

 

 

RX

SYNC

 

 

LINE

RD

TRIB

T

 

R

 

 

AT

 

 

RDY

 

139

 

 

 

TRIB

TX

 

 

 

RX

SYNC

 

 

 

 

 

 

X

LINE

 

 

X

 

8.Use a Phillips head screwdriver to tighten the captive

screws on the line card.

2 X3811/2

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

AT-

 

 

 

 

 

 

 

 

SYNC

 

 

LX3811/3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

LINE

RDY

 

 

 

 

 

 

 

 

RX

TRIB

TX

 

 

 

AT-

LX3811/4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RX

SYNC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

TX

LINE

RDY

 

 

 

 

 

 

 

 

RX

TRIB

TX

 

 

 

 

AT-

LX3811/5

 

 

 

 

 

 

 

 

 

 

 

 

 

RX

 

SYNC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RX

LINE

RDY

 

 

 

 

 

 

 

 

 

TRIB

TX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RX

 

SYNC

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

AT-

 

 

LX3811/6

LINE

RDY

 

TRIB

TX

 

 

RX

SYNC

 

 

LINE

RD

TRIB

T

 

R

140

Note

Always tighten the captive screws to secure the line card to the chassis. This helps ensure that the fiber optic connectors at the back of the line card are securely connected to the backplane.

9.Repeat this procedure to install additional line cards.

For information about the line card LEDs, installing SFPs in the line card, and connecting fiber optic cables, refer to the

AT-LX3800UMulti-ServiceTransport System Installation and Maintenance Guide.