Alliance Laundry Systems CHM1766C User Manual

Size:
945.42 Kb
Download

Washer-Extractors

Cabinet Hardmount

A-SeriesMicrocomputer for OPL Models 2 Speed andVariable-Speed

Refer to Page 2 for Model Identification

1 2

3 4

5 6

<

<

CHM1766C

CHM1766C

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

 

 

 

www.comlaundry.com

Part No. F232224R1

 

 

 

 

 

 

May 2008

Programming

Table of

Contents

Model Identification ...........................................................................

2

Safety Information..............................................................................

3

Explanation of Safety Messages...........................................................

3

Important Safety Instructions ...............................................................

3

Safety Decals ........................................................................................

5

Operator Safety.....................................................................................

6

Programming ......................................................................................

7

Entering Program Mode .......................................................................

7

Cycle and Error Count ..........................................................................

7

Setup Mode...........................................................................................

7

Programming Cycle Segments .............................................................

8

Options for Each Segment ....................................................................

10

To Edit an Entire Wash Cycle Formula................................................

13

Agitation for the Cycle.....................................................................

13

Wash 1 – Wash 5 .............................................................................

13

Temperature Controlled Fill ............................................................

14

Rinse 1 – Rinse 6 .............................................................................

14

Temperature Controlled Fill ............................................................

15

Abnormal Conditions............................................................................

16

Door Open During Operation ..........................................................

16

Excessive Fill Time..........................................................................

16

Out of Balance .................................................................................

16

Door Will Not Open.........................................................................

16

Excessive Drain Time ......................................................................

16

Temperature Probe Sensor Problem ................................................

16

Clean Filter LED On........................................................................

16

Test Cycle .............................................................................................

16

Domestic Cycle Charts Custom............................................................

19

Cycles 1 - 24 ....................................................................................

19

International Cycle Charts Custom.......................................................

21

Cycles 31 - 46 ..................................................................................

21

© Copyright 2008, Alliance Laundry Systems LLC

All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.

F232225

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

1

Model Identification

Information in this manual is applicable to these models:

HC80ANV

SC40AN2

SC60ANF

UC30AN2

UC60ANF

 

 

 

 

 

SC125ANV

SC40ANV

SC80ANV

UC40AN2

UC60ANV

 

 

 

 

 

SC20AN2

SC60ANV

UC125ANV

UC40ANV

UC80ANV

 

 

 

 

 

SC30AN2

SC60AN2

UC20AN2

UC60AN2

 

 

 

 

 

 

2

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232224

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

DANGER

DANGER indicates the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the danger is ignored.

WARNING

WARNING indicates the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

CAUTION

CAUTION indicates the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

IMPORTANT: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

Important Safety Instructions

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

1.Read all instructions before using the washer.

2.Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION MANUAL for the proper grounding of the washer.

3.Do not wash textiles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

4.Do not add gasoline, dry-cleaningsolvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

5.Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer,turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable; do not smoke or use an open flame during this time.

6.Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This is a safety rule for all appliances.

7.Before the washer is removed from service or discarded, remove the door to the washing compartment.

8.Do not reach into the washer if the wash drum is moving.

F232224

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

3

Safety Information

9.Do not install or store the washer where it will be exposed to water and/or weather.

10.Do not tamper with the controls.

11.Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenanceinstructions or in publisheduser-repairinstructions that the user understands and has the skills to carry out.

12.To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electrical power source.

13.Use washer only for its intended purpose, washing textiles.

14.Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket.

15.ALWAYS disconnect the washer from electrical supply before attempting any service. Disconnect the power cord by grasping the plug, not the cord.

16.Install the washer according to the INSTALLATION INSTRUCTIONS. All connections for water, drain, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

17.To reduce the risk of fire, textiles which have traces of any flammable substances such as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc. or anything containing wax or chemicals such as in mops and cleaning cloths, must not be put into the washer. These flammable substances may cause the fabric to catch on fire by itself.

18.Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

19.Keep washer in good condition. Bumping or dropping the washer can damage safety features. If this occurs, have washer checked by a qualified service person.

20.If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

21.Be sure water connections have a shut-offvalve and that fill hose connections are tight. CLOSE theshut-offvalves at the end of each wash day.

22.Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open.

23.Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times (preferably in a locked cabinet).

24.Always follow the fabric care instructions supplied by the textile manufacturer.

25.Never operate the washer with any guards and/or panels removed.

26.DO NOT operate the washer with missing or broken parts.

27.DO NOT bypass any safety devices.

28.Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer.

Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer.

4

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232224

WARNING

This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty.

SW004

IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

WARNING

Install the machine on a level floor of sufficient strength. Failure to do so may result in conditions which can produce serious injury, death and/or property damage.

W703

Safety Information

CAUTION

Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury.

SW025

WARNING

Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.

SW014

Safety Decals

Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician.

To provide personal safety and keep the machine in proper working order, follow all maintenance and safety procedures presented in this manual. If questions regarding safety arise, contact the manufacturer immediately.

Use manufacturer-authorizedspare parts to avoid safety hazards.

F232224

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

5

Safety Information

Operator Safety

WARNING

NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury.

SW012

To ensure the safety of machine operators, the following maintenance checks must be performed daily:

1.Prior to operating the machine, verify that all warning signs are present and legible. Missing or illegible signs must be replaced immediately. Make certain that spares are available.

2.Check door interlock before starting operation of the machine:

a.Attempt to start the machine with the door open. The machine should not start with the door open.

b.Close the door without locking it and attempt to start the machine. The machine should not start with the door unlocked.

c.Close and lock the door and start a cycle. Attempt to open the door while the cycle is in progress. The door should not open.

If the door lock and interlock are not functioning properly, call a service technician.

3.Do not attempt to operate the machine if any of the following conditions are present:

a.The door does not remain securely locked during the entire cycle.

b.Excessively high water level is evident.

c.Machine is not connected to a properly grounded circuit.

Do not bypass any safety devices in the machine.

WARNING

Never operate the machine with a bypassed or disconnected balance system. Operating the machine with severe out-of-balanceloads could result in personal injury and serious equipment damage.

SW039

6

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232224

Programming

NOTE: The machines are factory-programmedwith basic cycles to make the units operational without programming at the installation.

Entering Program Mode

1.Open machine lid.

2.Locate Program/Run switch on the computer board. This is accessed through a cutout in the metal control unit cover. This switch protrudes from the rear of the electronic control unit cover.

3.Flip switch to the left (as seen from the front of machine) to enter PROGRAM Mode.

4.Display will show temperature.

Cycle and Error Count

The control logs cycle count (total of all cycles completed).

1.To read, enter PROGRAM Mode.

2.Press START (Enter) keypad. Display will show the cycle count.

3.Press START (Enter) keypad. Display will show certain error conditions that may have been recorded by the control.

4.Read the information when consulting technical assistance as needed.

5.Step through the error log by pressing START keypad repeatedly until display reverts to normal PROGRAM Mode (“0000” or a temperature).

Setup Mode

NOTE: In SETUP Mode, certain machine functions can be configured. The settings in this mode are related to how the machine is equipped from the factory. Usually, these settings would not be changed.

NOTE: Enter SETUP Mode through the Program Mode.

1.Press (6) keypad. Display will show “FAr” or “CEL”.

NOTE: This selects whether temperatures display in degrees Fahrenheit (F) or Celsius (C), if control is equipped with a temperature sensor. Change selection by pressing or keypad.

NOTE: Changing degrees “FAr” or “CEL” only has an effect if the control has a temperature probe connected and/or heat capability.

2.Press START keypad.

3.Select “HEAt” or “noHt”. Change the selection by pressing the or keypad.

NOTE: If set for “HEAt”, the control has heat capability enabled. The washer-extractorMUST have electric or steam heat, and a temperature probe. If display shows “noHt”, or if the message “HEAt” or “noHt” does NOT display, the control does NOT have heat capability.

4.Press START keypad to continue to the next step.

5.Select “AFIL” or “SUP5”. For “SUP5”, a fifth or sixth supply can be programmed in a cycle step. “AFIL” allows auxiliary fills to be programmed to low, medium or high water level in a cycle step.

6.Press START keypad.

7.Select “tFIL” or “ntFL.” “tFIL” allows a temperature controlled fill to be programmed for any segment. Select “ntFL” to disable the feature.

WARNING

To avoid personal injury, recommended inlet water temperature should be no higher than 125° Fahrenheit (51° Celsius).

W709

8.Press START keypad.

9.Select “COOL” or “noCL.” “COOL” enables an automatic cooldown feature allowing cold water to flush into wash before a drain if temperature is 140°F (60°C) or above. Select “noCL” to disable feature.

10.Press START keypad.

11.Select “bEEP” (control sounds beeper during Add Bleach [Supply 2]) or “nobP” (control does NOT sound beeper during Add Bleach [Supply 2]). Change selection by pressing or keypad.

12.Press START keypad.

13.Select “Adv” or “noAd”. “Adv” enables the Rapid Advance feature. Select “noAd” to disable the feature.

14.Press START keypad.

F232224

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

7

Programming

Programming Cycle Segments

The machine has 30 wash cycles available. 26 wash cycles are pre-programmed.4 cycles are available for custom programming. All wash cycles may be edited as follows.

1.Enter PROGRAM Mode. Refer to Entering Program Mode section.

2.Press “ ” keypad to enter PROGRAM Mode.

3.Press the cycle number of the cycle to be edited. Refer to Table 1.

4.Press the START keypad to move into the menu of options. Refer to Figure 1.

NOTE: While cycle is running, pressing the START keypad shows the temperature. Pressing the START keypad a second time displays the cycle. Pressing the START keypad a third time returns display to time remaining.

15

14

13

12

11

10

16

17

18

19

1

 

 

 

2

 

 

 

 

5

1

2

6

3

4

7

5

6

8

<

<

9

3

4

CHM1766C

 

 

 

CHM1766C

1

Cycle Keypad “1”

11

Door Open LED

2

Cycle Keypad “3”

12

Spin Cycle LED

3

Cycle Keypad “5”

13

Rinse Cycle LED

4

Rapid Advance/Up “ ” Edit

14

Add Bleach LED

5

Cycle Keypad “2”

15

Wash Cycle LED

6

Cycle Keypad “4”

16

Out-of-BalanceIndicator Dot

7

Cycle Keypad “6”

 

(Variable-speedonly)

8

Stop/Down “ ” Edit

17

High Water Level Indicator Dot

9

START Keypad

18

Medium Water Level Indicator Dot

10

CLEAN FILTER Indicator LED

19

Low Water Level Indicator Dot

Figure 1

8

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232224