SpeedTouch™546
Residential ADSL Gateway
User’s Guide
Release R5.3.1
SpeedTouch™
546
User’s Guide
R5.3.1
Copyright
Copyright ©1999-2005 THOMSON. All rights reserved.
Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
Thomson Telecom Belgium Prins Boudewijnlaan, 47 B-2650 Edegem
Belgium www.speedtouch.com
Trademarks
The following trademarks are used in this document: SpeedTouch™ is a trademark of THOMSON.
Microsoft®, MS-DOS®, Windows® and Windows NT® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.
Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and other countries.
Adobe, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incorporated, registered in the United States and/or other countries.
Netscape® and Netscape Navigator® are registered trademarks of Netscape Communications Corporation. Ethernet™ is a trademark of Xerox Corporation.
UPnP™ is a certification mark of the UPnP™ Implementers Corporation.
Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Alliance", their respective logos and "Wi-Fi Protected Access" are trademarks of the Wi-Fi Alliance.
Other products may be trademarks or registered trademarks of their respective manufacturers.
Document Information
Status: v1.0 (May 2005)
Reference: E-DOC-CTC-20050429-0100
Short Title: User’s Guide ST546 R5.3.1
Contents
About this User’s Guide .............................................. |
1 |
1 |
Your SpeedTouch™ ...................................................... |
3 |
1.1 |
SpeedTouch™ Features.................................................................. |
4 |
1.1.1 |
Hardware Specifications.................................................................................. |
5 |
1.1.2 |
Software Features .......................................................................................... |
6 |
1.2 |
SpeedTouch™ LED Behaviour ........................................................ |
8 |
1.3 How to Access your SpeedTouch™................................................ |
9 |
|
1.3.1 Access via the Web Interface......................................................................... |
10 |
|
1.3.2 |
Access via CLI ............................................................................................. |
11 |
1.3.3 |
Access via FTP ............................................................................................ |
13 |
1.3.4 |
Remote Assistance ....................................................................................... |
16 |
2 Local Network Setup .................................................. |
17 |
3 Internet Connectivity Dial-In Clients ......................... |
19 |
|
3.1 |
SpeedTouch™ Web Pages ............................................................ |
21 |
3.2 |
IGD Control Agent ....................................................................... |
23 |
3.3 |
MS Windows XP BroadBand Connection ..................................... |
25 |
3.4 |
Mac OS X PPPoE Dial-in Client.................................................... |
29 |
4 SpeedTouch™ Web Interface .................................... |
31 |
E-DOC-CTC-20050429-0100 v1.0
i
Contents
ii
4.1 |
Navigation.................................................................................... |
32 |
4.1.1 |
Menu .......................................................................................................... |
33 |
4.1.2 |
Language Bar............................................................................................... |
34 |
4.1.3 |
Navigation Bar ............................................................................................. |
35 |
4.1.4 |
Notification Area .......................................................................................... |
36 |
4.1.5 |
Tasks.......................................................................................................... |
37 |
4.2 |
Home ............................................................................................ |
38 |
4.3 |
SpeedTouch ................................................................................. |
39 |
4.3.1 |
Information.................................................................................................. |
40 |
4.3.2 |
SpeedTouch™ Easy Setup .............................................................................. |
41 |
4.3.3 |
Restart........................................................................................................ |
42 |
4.3.4 |
Configuration ............................................................................................... |
43 |
4.3.5 |
Backup & Restore......................................................................................... |
44 |
4.3.6 |
Reset to Factory Defaults .............................................................................. |
45 |
4.3.7 |
Event Logs .................................................................................................. |
46 |
4.3.8 |
Update........................................................................................................ |
47 |
4.4 |
Broadband Connection................................................................. |
48 |
4.4.1 |
Connectivity Check....................................................................................... |
49 |
4.4.2 |
DSL Connection ........................................................................................... |
50 |
4.4.3 |
Internet Services .......................................................................................... |
51 |
4.4.4 |
Internet Service Settings ............................................................................... |
52 |
4.5 |
Toolbox ........................................................................................ |
53 |
4.5.1 |
Remote Assistance ....................................................................................... |
54 |
4.5.2 |
Game & Application Sharing .......................................................................... |
55 |
4.5.3 |
Defined Games & Applications ....................................................................... |
56 |
4.5.4 |
Game or Application Definition ....................................................................... |
57 |
4.5.5 |
New Game or Application .............................................................................. |
58 |
4.5.6 |
Parental Control ........................................................................................... |
59 |
4.5.7 |
Web Filtering Activation ................................................................................ |
62 |
4.5.8 |
Content Level .............................................................................................. |
63 |
4.5.9 |
New Content Level ....................................................................................... |
64 |
4.5.10 |
Firewall ....................................................................................................... |
66 |
4.5.11 |
Intrusion Detection ....................................................................................... |
67 |
4.5.12 |
Dynamic DNS .............................................................................................. |
68 |
4.5.13 |
User Management ........................................................................................ |
69 |
4.5.14 |
Edit User ..................................................................................................... |
70 |
4.5.15 |
Change Default User..................................................................................... |
71 |
4.5.16 |
Add User..................................................................................................... |
72 |
E-DOC-CTC-20050429-0100 v1.0
Contents
4.6 |
Home Network ............................................................................. |
73 |
4.6.1 |
Devices....................................................................................................... |
74 |
4.6.2 |
Device Settings ............................................................................................ |
75 |
4.6.3 |
Assign Public IP ........................................................................................... |
76 |
4.6.4 |
Interfaces .................................................................................................... |
77 |
4.6.5 |
Interface Settings ......................................................................................... |
78 |
4.6.6 |
DHCP Pool................................................................................................... |
79 |
5 Software Upgrade....................................................... |
81 |
5.1 Upgrade Wizard on Setup CD....................................................... |
82 |
6 |
Troubleshooting.......................................................... |
85 |
6.1 |
General SpeedTouch™ Troubleshooting ...................................... |
86 |
6.1.1 |
Ethernet Troubleshooting............................................................................... |
87 |
6.1.2 |
Upgrade Troubleshooting............................................................................... |
88 |
6.2 |
UPnP™ on Windows XP Systems................................................. |
89 |
6.3 |
Reset to Factory Defaults ............................................................ |
91 |
E-DOC-CTC-20050429-0100 v1.0
iii
Contents
iv
E-DOC-CTC-20050429-0100 v1.0
About this User’s Guide
!
A note provides additional information about a topic.
A tip provides an alternative method or shortcut to perform an action.
A caution warns you about potential problems or specific precautions that need to be taken.
Terminology |
Generally, the SpeedTouch™546(i) will be referred to as SpeedTouch™ in this User’s |
|
Guide. |
Typographical |
|
In interactive input and output, typed input is displayed in a bold font and |
|
Conventions |
commands are displayed like this. |
|
Comments are added in italics. |
|
Example: |
=>language list
CODE |
LANGUAGE VERSION |
FILENAME |
|
en* |
english 4.2.0.1 |
<system> |
Only one language is available |
Documentation and
software updates
E-DOC-CTC-20050429-0100 v1.0
THOMSON continuously develops new solutions, but is also committed to improve its existing products.
For more information on THOMSON's latest technological innovations, documents and software releases, visit us at:
www.speedtouch.com
1
About this User’s Guide
2 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 1
Your SpeedTouch™
E-DOC-CTC-20050429-0100 v1.0 |
3 |
|
Chapter 1
Your SpeedTouch™
In this section you will find a comprehensive overview of the:
Hardware Specifications
Software Features
4 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 1
Your SpeedTouch™
ADSL over POTS for a SpeedTouch™ADSL/POTS variant) ADSL over ISDN for a SpeedTouch™ ADSL/ISDN variant)
ADSL/RE-ADLS2/ADSL2/ADSL2+ for both ADSL over POTS and ADSL over ISDN
LAN: Four RJ-45 ports to connect up to 4 PCs to a 10/100 Base-T Ehternet network
Power inlet
E-DOC-CTC-20050429-0100 v1.0 |
5 |
|
Chapter 1
Your SpeedTouch™
1.1.2 |
Software Features |
ADSL compliance |
|
If POTS in overlay: G. handshake, Full Rate ADSL, G.dmt, G.lite (splitterless |
|
|
ADSL), ADSL2, RE-ADSL and ADSL2+ |
|
If ISDN in overlay: G.handshake, G.dmt, ADSL2, RE-ADSL and ADSL2+ |
ATM features |
|
Up to 16 simultaneous PVCs, allowing multiple simultaneous destinations |
|
|
ATM QoS per PVC: CBR, VBR-rt, VBR-nrt, UBR |
|
RFC 1483 / 2684 multiprotocol encapsulation over AAL5 / ATM: both LLC / |
|
SNAP and VC-based multiplexing supported |
Bridging features |
|
Multiport self-learning transparent bridge per IEEE 802.1D for LAN interconnect |
|
|
Remote bridge ports are isolated from each other |
|
Pre-defined bridge filters to WAN (no filter, no CPE-to-WAN broadcast, PPPoE |
|
only) and to LAN (no filter, multicast filter) |
Routing features |
|
Multi-port (up to 16 PVCs) router |
|
|
Static routing, automatic routes (PPP, LAN) |
|
IP address multi-homing |
Services |
|
UPnP with NAT traversal capability: |
|
|
enables game technologies (Xbox live, Direct X, and many others) |
|
enables conferencing functions of Microsoft Messenger |
|
Transparent bridging (IEEE802.1D) |
|
PPPoE routing/bridging with integrated PPP Relay |
|
PPPoA routing, PPPoA-to-PPTP relaying |
|
IP routing with static routing, packet classified routing and residential RIP |
|
Hyper-NAT with virtual server mapping (for instance for Web, FTP, Mail |
|
servers) and ALGs (such as NetMeeting, MSN Messenger, VPN passthrough, |
|
and others) |
|
Quality of Service: |
|
IP QoS |
|
Integrated Dynamic DNS client |
Security |
|
PAP (RFC1334), CHAP (RFC1994) for PPP session |
|
|
Integrated Stateful Inspection Firewall, Intrusion Detection |
|
Parental Control, URL Filtering |
|
Multi-level SpeedTouch™ access policies, Digest Authentication |
Configuration |
|
Home Install Wizard, Easy Setup wizard |
|
|
Intuitive web-based GUI (HTTP/HTTPs) |
|
Advanced configuration via telnet - Command Line Interface (CLI) |
|
Remote management access control |
6 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 1
Your SpeedTouch™
DHCP server, client and relay, DHCP-to-PPP spoofing
DNS server, client and relay
Time synchronization:
SNTPv1, SNTPv2, SNTPv3 and SNTPv4
System logging
SNMPv1 agent with MIB-II
Firmware upgradeable via upgrade wizard on Setup CD
E-DOC-CTC-20050429-0100 v1.0 |
7 |
|
Chapter 1
Your SpeedTouch™
Power Ethernet |
DSL |
Internet |
|
Following table shows the meaning of the different LEDs:
Indicator |
|
|
Description |
|
|
|
|
Name |
Colour |
State |
|
|
|
|
|
Power |
Green |
On |
Power on, normal operation |
|
|
|
|
|
Red |
On |
Power on, self-test failed, indicating |
|
|
|
device malfunction |
|
|
|
|
|
Orange |
On |
Bootloader active |
|
|
|
|
|
Off |
|
Power off |
|
|
|
|
Ethernet |
Green |
Flashing |
Ethernet activity |
|
|
|
|
|
|
On |
Ethernet connection, no activity |
|
|
|
|
|
Off |
|
No Ethernet connection |
|
|
|
|
DSL |
Green |
Flashing |
Pending DSL line synchronisation |
|
|
|
|
|
|
On |
DSL line synchronised |
|
|
|
|
|
Off |
|
No DSL line |
|
|
|
|
Internet |
Green |
Flashing |
Internet activity |
|
|
|
|
|
|
On |
Internet connectivity, no activity |
|
|
|
|
|
Red |
On |
Internet connection setup failed |
|
|
|
|
|
Off |
|
No Internet connection |
|
|
|
|
8 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 1
Your SpeedTouch™
Access Method |
Can be used to: |
|
|
Web |
Configure your SpeedTouch™ via HTTP or |
|
HTTPS. |
|
For more information, see “1.3.1 Access via |
|
the Web Interface” on page 10. |
|
|
Command Line Interface (CLI) |
Fine tune your SpeedTouch™ configuration. |
|
For more information, see “1.3.2 Access via |
|
CLI” on page 11. |
|
|
File Transfer Protocol (FTP) |
Backup and restore data on your SpeedTouch™. |
|
For more information, see “1.3.3 Access via |
|
FTP” on page 13. |
|
|
Remote Assistance |
Allow a remote user to help you configuring |
|
your SpeedTouch™. |
|
For more information, see “1.3.4 Remote |
|
Assistance” on page 16. |
|
|
E-DOC-CTC-20050429-0100 v1.0 |
9 |
|
Chapter 1
Your SpeedTouch™
1Open a web browser.
2In the address bar type your SpeedTouch™’s IP address or DNS host name, by default that is ‘http://speedtouch.lan’ or ‘192.168.1.254’.
You can access the pages via the http protocol. For remote assistance the secure version, https, in combination with certificates is used; provide your ISP with the https link, user name and password before he can log on to the pages. For more information, see “1.3.4 Remote Assistance” on page 16.
3As a result the SpeedTouch™ Home page appears, from where you can navigate to all the configurable aspects of the SpeedTouch™.
For more information on the web pages, see “4 SpeedTouch™ Web Interface” on page 31.
10 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 1
Your SpeedTouch™
Command Line
Interface (CLI)
You can access the Command Line Interface (CLI) via: A Telnet session
This requires that TCP/IP connectivity exists between the host from which the Telnet session is opened and the SpeedTouch™. Your SpeedTouch™ and the connected PC must have an IP address in the same subnet.
Quote site commands (over FTP)
For more information, see “ Quote site command” on page 15.
For information on CLI commands, see the SpeedTouch™ CLI Reference Guide.
E-DOC-CTC-20050429-0100 v1.0 |
11 |
|
Chapter 1
Your SpeedTouch™
1 Open a telnet application.
You can use the Command Prompt window. In Windows XP for instance:
1On the Windows task bar, click Start.
2Select (All) Programs > Accessories > Command Prompt.
2 Connect to your SpeedTouch™. .
In the Command Prompt window:
At the prompt, type telnet followed by the IP address of your SpeedTouch™ (default is 192.168.1.254).
3 Enter your SpeedTouch™ security user name and password.
The default user is ‘Administrator’ and the default password is blank.
4 As soon as you’ve opened a session to the CLI, the SpeedTouch™ banner is displayed, followed by the CLI prompt, as shown in the example below:
Username : Administrator
-----------------------------------------------------------------------
- |
|
|
|
|
|
|
|
|
|
|
|
|
* |
|
|
|
|
|
|
______ |
SpeedTouch |
|
|||
* |
|
|
|
|
___/_____/\ |
|
|
|
|
|||
* |
|
|
|
|
/ |
|
|
/\\ |
Version 5.3 |
|||
* |
|
|
|
_____/__ |
|
|
/ |
\\ |
|
|
|
|
* |
|
|
|
_/ |
/\_____/___ \ |
Copyright (c) 1999-2005, |
||||||
* |
|
|
|
// |
/ |
\ |
|
/\ \ |
|
|
THOMSON |
|
* |
|
_______//_______/ |
|
\ |
/ _\/______ |
|
|
|||||
* |
|
/ |
/ \ |
\ |
|
/ |
/ / |
|
/\ |
|
|
|
* |
__/ |
/ |
|
\ |
\ / |
|
/ / |
|
/ _\__ |
|||
* |
/ / |
/ |
|
\_______\/ |
|
|
/ / |
|
/ / |
|
/\ |
|
* /_/______/___________________/ /________/ /___/ |
\ |
|||||||||||
* \ \ |
\ |
|
___________ |
|
|
\ \ |
|
\ \ |
\ |
/ |
||
* |
\_\ |
\ |
/ |
|
/\ |
|
|
\ \ |
|
\ \___\/ |
||
* |
\ |
\/ |
|
/ |
\ |
|
\ \ |
|
\ |
/ |
|
|
* |
|
\_____/ |
|
|
/ |
|
\ |
\ \________\/ |
|
|
||
* |
|
/__________/ |
|
\ |
\ |
/ |
|
|
|
|||
* |
|
\ |
|
_____ |
\ |
|
/_____\/ |
|
|
|
||
* |
|
\ / |
/\ |
\ |
|
/___\/ |
|
|
|
|
||
* |
|
|
/____/ |
\ \ |
/ |
|
|
|
|
|
|
|
* |
|
|
\ |
\ |
/___\/ |
|
|
|
|
|
|
|
* |
|
|
\____\/ |
|
|
|
|
|
|
|
|
-----------------------------------------------------------------------
{Administrator}=>
12 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 1
Your SpeedTouch™
File Transfer Protocol
(FTP)
You can access the file system of the SpeedTouch™ via the File Transfer Protocol (FTP), in order to:
Restore or backup configuration files, templates or language packs. Upgrade your configuration or firmware.
1 Open a Command Prompt window. In Windows XP for instance:
1On the Windows task bar, click Start.
2Select (All) Programs > Accessories > Command Prompt.
2At the prompt, type ftp followed by the IP address of your SpeedTouch™ (default is 192.168.1.254).
3Enter your SpeedTouch™ security user name and password.
The default user is ‘Administrator’ and the default password is blank.
4 The example below shows an FTP session to the SpeedTouch™ file system:
The root directory contains:
all the necessary files for the SpeedTouch™ to boot correctly the dl directory
The dl (download) directory contains the software image.
If you made changes to the SpeedTouch™ configuration and saved them, a user.ini configuration settings file is created in the dl subdirectory.
E-DOC-CTC-20050429-0100 v1.0 |
13 |
|
Chapter 1
Your SpeedTouch™
File system access On the different directories you have following privileges: rights
Directory |
Access rights |
|
|
root |
NO read/write |
|
|
dl |
read/write |
|
|
Common FTP
commands
Depending on the access rights you have on a directory, you can use one of following commands:
Command... |
You can use to... |
|
|
cd |
access another directory than the one currently open. |
|
Example: ftp>cd dl. |
|
|
dir |
list the directory files. |
|
Example: ftp>dir. |
|
|
bin |
set the transfer mode to ‘binary’. |
|
|
hash |
turn on the hashing option. |
|
|
put |
upload files. |
|
Example: ftp>put C:/MyBackupFiles/user.ini. |
|
A configuration file must be uploaded to the dl directory. |
|
|
get |
download files. |
|
Example: ftp>get user.ini. |
|
Downloading the configuration file must be done from the dl |
|
directory. |
|
|
delete |
delete files. |
|
|
bye |
quit FTP. |
|
|
14 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 1
Your SpeedTouch™
Turn on the hashing option to see the progression of the file transfer: At the ftp prompt type hash and press Enter.
Example:
/home/doejohn{1}$ftp 192.168.1.254 Connected to 192.168.1.254
220 Inactivity timer = 120 seconds. Use 'site idle <secs>' to change. Name (192.168.1.254:doejohn):
331 SpeedTouch™ (00-90-D0-01-02-03) User 'doejohn' OK. Password requir ed.
Password : ######
330 OK ftp> ftp>bin
200 TYPE is now 8-bit binary ftp>
ftp>hash
200Hash mark printing on (8192 bytes/hash mark). ftp>cd dl
250 Changed to /dl ftp>put C:\user.ini
200 Connected to 192.168.1.10 port 1271
150 Opening data connection for user.ini
226 File written successfully
ftp: 256 bytes sent in 0,000Seconds 256000,000Kbytes/sec. ftp>
Example: To execute the CLI command :software cleanup: At the FTP prompt type ‘quote site software cleanup’ and press Enter.
ftp> quote site software cleanup 200-
200 CLI command "software cleanup" executed ftp>
For more information on CLI commands, see the CLI Reference Guide.
E-DOC-CTC-20050429-0100 v1.0 |
15 |
|
Chapter 1
Your SpeedTouch™
1Go to the SpeedTouch™ pages, as described in “1.3.1 Access via the Web Interface” on page 10.
2In the menu select Toolbox > Remote Assistance.
3Click Enable Remote Assistance.
4Provide the following parameters to your helpdesk:
URL (the HTTPS link)
User name
Password
5Your ISP is now able to access your SpeedTouch™ via the secure HTTPs link in combination with the provided certificate (a secure authentication mechanism).
For security reasons, after 20 minutes of inactivity, or on reboot, Remote Assistance will be automatically disabled.
To disable remote assistance:
1Go to the SpeedTouch™ pages, as described in “1.3.1 Access via the Web Interface” on page 10.
2In the menu select Toolbox > Remote Assistance.
3Click Disable Remote Assistance.
16 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 2
Local Network Setup
Using the SpeedTouch™ Ethernet switch, you can create a local Ethernet network of up to four devices, without needing extra networking devices
In the SpeedTouch™ package, a yellow full-wired straight-through RJ-45/RJ- 45 Ethernet cable is included.
Standard wiring Use the yellow Ethernet cable provided to wire your computer’s Ethernet port to the procedure one of the SpeedTouch™’s Ethernet ports.
The Ethernet cable can also be used to wire any Ethernet port of your SpeedTouch™ to an external hub or switch.
Please follow the installation instructions supplied with the external hub or switch for connections and Ethernet cabling.
E-DOC-CTC-20050429-0100 v1.0 |
17 |
|
Chapter 2
Local Network Setup
18
Once you’ve connected a device, you are able to personalise its settings:
1Go to the SpeedTouch™ web pages.
2In the menu select Home Network > Devices.
3Click the name of your device, or if the device’s settings haven’t been personalised yet, click the MAC address of the device.
4On the top right, click Configure.
5Now you can change the device’s name, lock its IP address and assign applications and services to the device.
Depending on the SpeedTouch™ model, LED indicators allow you to check your Ethernet. See “1.2 SpeedTouch™ LED Behaviour” on page 8 for more information.
E-DOC-CTC-20050429-0100 v1.0
Chapter 3
Internet Connectivity Dial-In Clients
As soon as the initial configuration has been done, immediate and uninterrupted WAN access is provided.
In case of direct access, the remote organisation might ask for a user name and password on an Internet welcome page.
Dial-in access:
Access must be explicitly established, that is by “dialling” into a Broadband Remote Access Server (BRAS).
Depending on the SpeedTouch™ configuration, dial-in access is provided via the SpeedTouch™’s Routed PPPoA or Routed PPPoE packet services with embedded PPP client.
More information on connection protocols can be found in the Internet Connection Configuration Guide.
Dial-in clients There are different ways of dialling in, depending on the operating system on your PC and your preferences.
Dial-in method: |
|
can be used on |
For more information, |
|
|
following operating |
see: |
|
|
system: |
|
|
|
|
|
Embedded PPP dial-in client: |
|
|
|
|
|
|
|
Dial-in client on |
|
MS Windows, Mac, unix, |
“3.1 SpeedTouch™ Web |
embedded pages |
|
other |
Pages” |
|
|
|
|
MS Windows XP IGD |
|
MS Windows XP |
“3.2 IGD Control Agent” |
Control Agent for UPnP |
|
|
on page 23 |
|
|
|
|
Host PPP dial-in client for a SpeedTouch™ configured in pure bridging mode: |
|||
|
|
|
|
MS Windows XP |
|
MS Windows XP |
“3.3 MS Windows XP |
Broadband connection |
|
|
BroadBand Connection” |
|
|
|
|
Mac OS X PPPoE dial-in |
|
Mac OS X |
“3.4 Mac OS X PPPoE |
client |
|
|
Dial-in Client” |
|
|
|
|
E-DOC-CTC-20050429-0100 v1.0 |
19 |
|
Chapter 3
Internet Connectivity Dial-In Clients
The SpeedTouch™’s embedded PPP dial-in client allows you to establish an Internet connection for computers residing on your local network, using only one computer of the network to control the client.
If this computer runs:
Any Operating System
you can always use the SpeedTouch™ web pages.
See “3.1 SpeedTouch™ Web Pages” on page 21 to proceed.
MS Windows XP
you can use MS Windows XP’s Internet Gateway Device Control Client. See “3.2 IGD Control Agent” on page 23 to proceed.
You can also connect to the Internet using a Broadband PPPoE dial-in application. The PPP over Ethernet connection scenario provides PPP-like dial-in behaviour over the virtual Ethernet segment.
To be able to use a broadband dial-in application on your computer for connecting to the Internet, the SpeedTouch™ needs to be configured for Bridged Ethernet or Routed PPPoE (with PPPoE relay) via the SpeedTouch™ Home Install Wizard on the Setup CD or the embedded Easy Setup.
If this computer runs: MS Windows XP
you can use the MS Windows XP broadband dial-in client. See “3.3 MS Windows XP BroadBand Connection” on page 25 for more information.
Mac OS X
you can use a Mac OS X broadband dial-in client. See “3.4 Mac OS X PPPoE Dial-in Client” on page 29 for more information.
- or -
A broadband PPPoE dial-in client provided by your Service Provider to connect to the Internet
Upon availability of OS-specific PPPoE dial-in client applications, the
latter method is Operating System independent.
For PPPoE session connectivity from a Mac OS 8.6/9.x, an MS Windows 95/98(SE)/ME/2000 or a Linux system, a host PPPoE dial-in application is mandatory.
20 |
E-DOC-CTC-20050429-0100 v1.0 |
|
Chapter 3
Internet Connectivity Dial-In Clients
Starting an Internet
session
As the SpeedTouch™ web pages are controllable from any Operating System with an installed web browser, the method to establish PPP sessions described below you can use on any computer system.
For more information on Internet connection setup, see the provided Installation and Setup Guide.
Proceed as follows:
1Open a web browser on your computer and browse to the SpeedTouch™ web pages (see “1.3.1 Access via the Web Interface” on page 10 for more information):
By default the SpeedTouch™ shows you the Home page.
2Click Connect at the appropriate broadband connection.
You might be requested to enter your user name and password.
As a result SpeedTouch™’s embedded PPP dial-in client establishes the Internet connection.
3Now you can surf the Internet.
You are able to overview and monitor your Internet connectivity as long as the session is running via:
The SpeedTouch™ System Information page: see “4.3.1 Information” on page 40.
The SpeedTouch™ Diagnostics task: see “4.4.1 Connectivity Check” on page 49.
E-DOC-CTC-20050429-0100 v1.0 |
21 |
|
Chapter 3
Internet Connectivity Dial-In Clients
Terminating an Internet
session
22
To close an active PPP connection:
1Go to the SpeedTouch™ Home page.
2Click Disconnect at the appropriate broadband connection.
As a result the SpeedTouch™’s embedded PPP dial-in client will close the Internet connection. The Internet Link status will change to Disconnected and your PC is offline.
E-DOC-CTC-20050429-0100 v1.0