4-246-022-21 030227AMI-H-FM
Micro Hi-Fi Component System
XR-MN5
WARNING
The following caution label is located inside the apparatus.
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE TO BEAN.
ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR
STRÅLING.
VORSICHT: UNSICHTBARE LASERSTRAHLUNG. WENN ABDECKUNG GEÖFFNET
UND SICHEREITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL
AUSSETZENSTRÅLING.
VARO!: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT-TIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KÄTSO SÄTEESEEN.
En |
VARNING: OSYNLIG LASERSTRÅLING NÄR DENNA DEL ÄR ÖPPNAD OCH |
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. |
|
ADVERSEL: USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG |
|
|
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN. |
VIGYÁZAT!: A BURKOLAT NYITÁSAKOR LÁTHATATLAN LÉZERSU-GÁRVESZÉLY!
KERÜLJE A BESUGÁRZÁST!
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
This appliance is classified as a CLASS 1 LASER product.
This label is located on the rear exterior.
To prevent fire, do not cover the ventilation of the apparatus with newspapers, table-cloths, curtains, etc. And don't place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
Don't throw away the battery with general house waste, dispose of it correctly as chemical waste.
PRECAUTIONS
On operating voltage
Before operating the system, check that the operating voltage of your system is identical with the voltage of your local power supply.
On safety
•The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
•Unplug the system from the wall outlet (mains) if it is not to be used for an extended period of time. To disconnect the cord (mains lead), pull it out by the plug. Never pull the cord itself.
•Should any solid object or liquid fall into the component, unplug the stereo system and have the component checked by qualified personnel before operating it any further.
•The AC power cord must be changed only at a qualified service shop.
On placement
•The unit should be situated with adequate space around it so that proper heat ventilation is assured. Allow 10 cm clearance from the rear and the top of the unit, and 5 cm from each side.
•Do not place the unit in an inclined position. •Do not place the unit in locations where it is;
-Extremely hot or cold
-Dusty or dirty
-Very humid
-Vibrating
-Subject to direct sunlight.
2
On heat buildup
•Although the unit heats up during operation, this is not malfunction.
•Place the unit in a location with adequate ventilation to prevent heat build-up in the unit.
If you continuously use this unit at a large volume, the cabinet temperature of the top, side and bottom rises considerable. To avoid burning yourself, do no touch the cabinet.
On operation
•If the system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the CD player. Should this occur, the system will not operate properly. Remove the CD and leave the system turned on for about an hour until the moisture evaporates.
•When you move the system, take out any discs.
Notes on discs
•Playable discs on this unit are Audio CDs (CDs), CD-R/ CD-RW with audio data (CD-R/RW) and CD-R/CD-RW with MP3 files (MP3-CDs).
•Discs recorded on CD-R/RW drives may not be played back because of scratches, dirt., recording condition or the drive's characteristics.
•CD-R/RW discs which are not finalized at the end of recording cannot be played back.
•Do not attach adhesive label, etc. to either side of a CD-R/ RW disc, as doing so may cause malfunction.
•Do not load an unrecorded CD-R/RW disc. The disc may be damaged.
•Do not insert 8-cm (3-inch) discs. Those discs cannot be played on this unit. Moreover, if you insert the discs of that
size forcibly, you may not be able to eject it.
•Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this unit. Attempting to do so may damage the unit. Do not use such discs.
•DVD, SACD, CD-ROM and VCD cannot be played on this unit.
Music discs encoded with copyright protection technologies
This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.
If you have any questions or problems concerning your stereo system, please consult your nearest Aiwa dealer.
TABLE OF CONTENTS
PRECAUTIONS .................................... |
2 |
|
PREPARATIONS ................................... |
4 |
|
PARTS AND CONTROLS ......................... |
5 |
|
ADJUSTMENTS BEFORE OPERATION .......... |
8 |
|
SOUND ADJUSTMENTS .......................... |
9 |
|
CD OPERATIONS ................................ |
10 |
|
MP3-CD OPERATIONS ......................... |
12 |
En |
TUNER OPERATIONS ........................... |
14 |
|
TAPE PLAYBACK ................................ |
17 |
|
TAPE RECORDING .............................. |
18 |
|
TIMER OPERATIONS ........................... |
21 |
|
REFERENCE ..................................... |
23 |
|
3
PREPARATIONS
Connection
Plug in the AC power cord to the AC power socket after all other connections are made.
1Connect the speaker cords to the speakers.
Connect the copper cords to the + terminals and the silver cords to the - terminals.
En
2Connect the speakers to the main unit.
Connect the right speaker to the SPEAKERS R terminals and the left to the SPEAKERS L terminals. The copper cords go to the 0terminals.
3Connect the supplied antennas.
Connect the FM antenna to the FM 75 Ω terminal and the AM antenna to the AM LOOP jack.
AM antenna
FM antenna
4Connect the AC power cord to an AC power socket.
When the AC power cord is connected to a wall outlet for the first time, DEMO appears in the display.
To deactivate the DEMO, press ECO/RDS or i-Bass/DEMO.
Speakers
•Do not short-circuit the 0and 9speaker cord leads. •Do not leave objects generating magnetism or objects
affected by magnetism near the speakers.
Antennas
Keep antennas away from metallic objects, electrical equipment and cords.
•FM antenna: Extend fully and position for the best
reception. If reception is poor, connect an optional outdoor antenna to the FM 75 Ω terminal. Note that, when connecting an optional outdoor antenna, use an adaptor as required.
•AM antenna: Rotate to find best reception.
Remote commander
Detach the battery compartment lid at the rear of the remote commander and insert two R6 (size AA) batteries with correct polarity.
R6(AA)
•Replace the batteries with new ones when the operational distance between the remote commander and main unit becomes shorter.
•Remove the batteries if the unit is not going to be used for an extended period of time.
•The remote commander may not operate if it is used under intense sunlight or if its line of sight is obstructed.
4
PARTS AND CONTROLS
Main unit: front
Refer to the pages indicated in parentheses for details.
1 |
6 |
|
|
2 |
|
3 |
7 |
|
|
4 |
8 |
5 |
9 |
|
|
|
0 |
1POWER 6STANDBY/ON (8)
Switches the unit on and off (standby).
2ECD (8, 10-12)
Starts and pauses CD play.
TUNER/BAND (8, 14)
Selects tuner function and the tuner band. dTAPE (REC MUTING) (8, 17, 19)
3 ECO/RDS (8, 14-16) |
8 |
Sets the ECO mode on or off. |
|
Tuner: Activates RDS features. |
|
SYNCHRO REC (18) |
9 |
Starts recording and CD play simultaneously. |
|
REC START/REC PAUSE (18-20) |
0 |
Starts and pauses recording. |
|
4s(10-12, 17, 18, 20)
CD and Tape: stops playback. Tuner: clears a preset station.
TUNING f/r-, +t/g(8,10-12,
14, 17, 21, 22)
CD: skips to a previous or a succeeding track when pressed, searches a track in fast forward or reverse playback when held down.
Tape: rewinds or fast forwards the tape.
Tuner: manually tunes up or down within the band.
5VOLUME (9)
Adjusts the volume.
6TREBLE (9)
Adjusts the treble level.
i-Bass/DEMO (4, 9)
Produces rich and clear low frequency sound. Switches DEMO on and off while the unit is turned off.
PUSH EJECTz(17-19)
Opens or closes the cassette holder.
PHONES jack
Plug in optional headphones set with a stereo mini plug |
|
(ø3.5 mm). Speaker output is cancelled. |
En |
|
Starts playback and changes the playback side.
Also used to enter 4-second blank spaces during recording.
AUX (8)
Selects the function of external equipment connected to AUX IN jacks.
BASS (9)
Adjusts the bass level.
7zCD EJECT (10, 12)
Ejects the disc(s).
CD slot buttons (1-5) (8, 10-12)
Selects a disc slot.
Starts CD play for one desired disc.
5
Main unit: rear
Refer to the pages indicated in parentheses for details.
|
1 |
|
|
2 |
|
En |
3 |
|
4 |
||
5 |
||
|
||
|
6 |
1AM LOOP jack and FM 75 Ω terminal (4)
Plug in the supplied AM and FM antennas.
2SUB WOOFER3jack
Connect optional powered sub woofer with a built-in amplifier to the jack.
3DIGITAL OUT (OPTICAL) jack
CD digital sound signals can be output through this jack. Use an optical cable to connect digital audio equipment. Fit an optical cable plug in the DIGITAL OUT (OPTICAL) jack and push it to connect.
4AUX IN jacks
Accept analogue sound signals from external equipment. Connect external equipment using an optional connecting cable with RCA phono plugs (red plug to R jack, white plug to L jack). Refer also to the operating instructions for your equipment.
To switch function to external input, press AUX.
To change a source name in the display of the AUX function.
Hold down AUX and press POWER while the power is on.
AUX 
VIDEO
TV 
5SPEAKERS3terminals (4)
Connect the speaker cords of the supplied speakers.
6AC power cord (4)
6
Remote commander
Refer to the pages indicated in parentheses for details.
1
8
2
9
3
0
4 |
! |
|
5 |
||
@ |
||
6 |
||
# |
||
7 |
||
|
Buttons with the same or similar names on the main unit basically have the same function.
1POWER (8)
21–10/0, >10 (10-12, 15, 19, 20)
CD: selects a track of the specified number.
Tuner: tunes in the station with the specified preset number.
The numbered buttons take on these functions when pressed with SHIFT held down:
CLOCK (8)
Selects clock mode.
TIMER (21, 22)
Selects timer mode.
MUTING (9)
To turn off the sound temporarily.
TUNER MODE (15)
Switches between stereo or monaural FM reception.
REV MODE (17, 18, 22)
Selects a reverse mode.
DISC/ALBUM (12)
Selects disc mode or album mode on an MP3-CD.
CD EDIT/CHECK (19, 20)
Selects edited CD recording.
3SHUFFLE/PROGRAM (11)
Selects shuffle or programmed CD playback mode.
REPEAT (11)
Selects repeat CD playback mode.
4ALBUM/PRESETN,M(12, 15)
MP3-CD:Skips to a previous or succeeding album. Tuner: Tunes in a preset station.
f/r,t/g(8, 10-12, 14, 17, 21,
22)
ENTER (8, 14, 15, 21, 22)
Determines the mode.
Stores the received station to preset.
5ECD (8, 10-12)
TUNER/BAND (8, 14) dTAPE (8, 17)
AUX (8)
6DISPLAY (10, 12)
Changes the display in CD playback mode.
DIMMER (8)
Adjusts the display window brightness.
SLEEP (21)
Selects sleep-timer mode.
7SHIFT
Hold down when pressing a numbered button to change its function to that printed above the number.
8DISC SELECT (10, 12)
Selects a desired CD slot.
9 CLEAR (11, 15, 21, 22) |
En |
CD: Clears a CD program
Tuner: Clears a preset station.
0 i-Bass (9)
TONE (9)
Selects the bass or treble adjusting mode.
! s(10-12, 17, 18, 20)
@FUNCTION (18-20)
Switches the active function among TAPE, TUNER, AUX (VIDEO or TV) and CD.
# VOLUME +,-(9)
7
ADJUSTMENTS BEFORE OPERATION
|
ECD, |
POWER |
|
POWER |
TUNER/ |
|
|
BAND, |
|
|
|
6STANDBY/ON |
dTAPE, |
CLOCK |
|
ECO/RDS |
AUX |
|
|
|
|
ENTER |
|
|
|
|
|
f,g |
|
ECD, |
f,g |
|
TUNER/ |
||
|
|
||
En |
|
BAND, |
|
dTAPE, |
|
||
|
|
AUX |
|
|
|
SHIFT |
|
|
|
DIMMER |
|
Power
Turning the unit on
Press POWER 6STANDBY/ON (POWER on the remote ). Alternatively, press dTAPE, TUNER/BAND, AUX, ECD or one of the CD slot buttons (1-5). Playback will start automatically if a disc or tape is loaded.
Turning the unit off
Press POWER 6STANDBY/ON again.
The unit goes into standby.
Dimmer
The display window brightness can be selected.
Press DIMMER on the remote.
Each press of the button changes between darker and brighter.
ECO mode
Reduces power consumption in standby mode with the following operations.
Press ECO/RDS.
Each press of the button changes the mode as follows;
ECO ON: Power economizing mode is activated.
When the unit turns off, everything on the display clears and only the red indicator above POWER lights to show that the power is being supplied.
ECO OFF: Power economizing mode is cancelled. When the unit turns off, the clock display appears.
Initial mode is ECO OFF.
Standby power consumption
ECO ON: 0.26 W
ECO OFF: 15 W
Setting the clock
1In stop mode, hold down SHIFT and press CLOCK on the remote.
Go to step 3 when the hour of the clock display flashes.
2Within 6 seconds, press ENTER.
The hour flashes in the display.
3Press for gto set the hour, then press ENTER.
4Press for gto set the minute.
Each press changes the time in 1-minute steps.
5Press ENTER.
The time display stops flashing and the clock starts from 00 seconds.
To display the time while the power is on
Hold down SHIFT and press CLOCK on the remote. The time will be displayed for 6 seconds.
If "- -:- -" appears when the unit is turned off
There has been a power interruption. Reset the clock.
8
Loading...