Compact Disc
Stereo System
XR-MG9
U
For assistance and information
(United States and Puerto Rico)
8B-CLR-903-01 010601AYK-H-B
OPERATING INSTRUCTIONS |
En (English) |
MANUAL DE INSTRUCCIONES |
E (Español) |
MODE D'EMPLOI |
F (Français) |
PRECAUTIONS
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
|
CAUTION |
En |
RISK OF ELECTRIC SHOCK |
DO NOT OPEN |
|
|
|
|
“CAUTION:TO REDUCE THE RISK OF |
|
ELECTRIC SHOCK, |
|
DO NOT REMOVE COVER (OR BACK). |
|
NO USER-SERVICEABLE PARTS INSIDE. |
|
REFER SERVICING TO QUALIFIED |
|
SERVICE PERSONNEL.” |
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
2
Read these Operating Instructions carefully and completely before operating the unit. All precautions in this booklet and on the unit should be strictly followed.
Keep the Operating Instructions for future reference.
Installation
1 Water and moisture — Do not use this unit near water, such as near a bathtub, washbowl, swimming pool, or the like.
2 Heat — Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that generate heat. It also should not be placed in temperatures less than 5° C (41° F) or greater than 35° C (95° F).
3Mounting surface — Place the unit on a flat, even surface.
4Ventilation — The unit should be situated with adequate space around it so that proper heat ventilation is assured. Allow 10 cm (4 in.) Clearance from the rear and the top of the unit, and 5 cm (2 in.) from each side.
-Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.
-Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.
5Objects and liquid entry — Make sure that objects or liquids do not get inside the unit through the ventilation openings.
6Carts and stands — When placed or
mounted on a stand or cart, the unit should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit or cart to overturn or fall.
7 Condensation — Moisture may form on the CD pickup lens when:
-The unit is moved from a cold spot to a warm spot
-The heating system has just been turned on
-The unit is used in a very humid room
-The unit is cooled by an air conditioner
When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again.
8 Wall or ceiling mounting — The unit should not be mounted on a wall or ceiling, unless specified in the Operating Instructions.
Electric Power
1Power sources — Connect this unit only to power sources specified in the Operating Instructions, and as marked on the unit.
2Polarization — As a safety feature, some units are equipped with polarized AC power plugs which can only be inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into an outlet, turn the plug over and try again. If it still does not easily insert into the outlet, please call a qualified service technician to service or replace the outlet. To avoid defeating the safety feature of the polarized plug, do not force it into a power outlet.
3AC power cord
-When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the cord itself.
-Never handle the AC power plug with wet hands, as this could result in fire or shock.
-Power cords should be firmly secured to avoid being severely bent, pinched, or walked upon. Pay particular attention to the cord from the unit to the AC outlet.
-Avoid overloading AC outlets and extension cords beyond their capacity, as this could result in fire or shock.
4Extension cord — To help prevent electric shock, do not use a polarized AC power plug with an extension cord, receptacle, or other outlet unless the polarized plug can be completely inserted to prevent exposure of the blades of the plug.
5When not in use — Unplug the AC power cord from the AC outlet if the unit will not be used for several months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off.
Outdoor Antenna
1 Power lines — When connecting an outdoor antenna, make sure it is located away from power lines.
2 Outdoor antenna grounding — Be sure the antenna system is properly grounded to provide protection against unexpected voltage surges or static electricity build-up. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information on proper grounding of the mast, supporting structure, and the lead-in wire to the antenna discharge unit, as well as the size of the grounding unit, connection to grounding terminals, and requirements for grounding terminals themselves.
Damage Requiring Service
Have the unit serviced by a qualified service technician if:
-The AC power cord or plug has been damaged
-Foreign objects or liquid have gotten inside the unit
-The unit has been exposed to rain or water
-The unit does not seem to operate normally
-The unit exhibits a marked change in performance
-The unit has been dropped, or the cabinet has been damaged DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.
Antenna Grounding According |
ANTENNA |
||
to the National Electrical Code |
LEAD IN |
||
|
|
WIRE |
|
GROUND CLAMP |
ANTENNA |
||
DISCHARGE |
|||
|
|
||
|
|
UNIT |
|
ELECTRIC |
|
(NEC SECTION |
|
|
810-20) |
||
SERVICE |
|
GROUNDING |
|
EQUIPMENT |
|
||
|
|
CONDUCTORS |
|
POWER SERVICE |
|
(NEC SECTION |
|
|
810-21) |
||
GROUNDING |
|
||
|
GROUND CLAMPS |
||
ELECTRODE SYSTEM |
|
||
|
|
||
(NEC ART 250 PART H) |
NEC-NATIONAL ELECTRICAL CODE |
||
Maintenance
Clean the unit only as recommended in the Operating Instructions.
OWNER'S RECORD
Record the model number and serial number of your set (found at the rear of your set) below. Refer to them when contacting your Aiwa dealer.
Model No. _____________________________
Serial No. _____________________________
TABLE OF CONTENTS
PRECAUTIONS .................................... |
2 |
|
PREPARATIONS ................................... |
4 |
|
PARTS AND CONTROLS ......................... |
5 |
|
ADJUSTMENTS BEFORE OPERATION .......... |
8 |
|
SOUND ADJUSTMENTS .......................... |
9 |
En |
CD OPERATIONS ................................ |
10 |
|
RADIO OPERATIONS ........................... |
12 |
|
TIMER OPERATIONS ........................... |
13 |
|
REFERENCE ..................................... |
14 |
|
System and accessories
Main unit CX-LMG9
Speakers SX-LMG9
Speakers cords
Remote control
Lithium battery (CR2025)
FM antenna
AM antenna
3
PREPARATIONS
Connection
Plug in the AC power cord to the AC outlet after all other connections are made.
1 Connect the speaker cords to the speakers.
Connect the amber cords to the + terminals and the silver
cords to the – terminals.
En
2Connect the speakers to the main unit.
Connect the right speaker to the SPEAKERS R terminals and the left to the SPEAKERS L terminals. The amber speaker cords go to the )terminals.
3 Connect the supplied antennas.
Connect the FM antenna to the FM 75 Ω terminals and the AM antenna to the AM LOOP jack.
AM antenna
FM antenna
4Connect the AC power cord to an AC outlet.
When the AC power cord is connected to an AC power outlet for the first time, DEMO appears on the display. To deactivate the DEMO, press DEMO/ECO and the clock will flash on the display. For setting the clock, see page 9.
Speakers
•Do not short-circuit the )and (speaker cord leads.
•Do not leave objects generating magnetism or objects affected by magnetism near the speakers.
Antennas
Keep antennas away from metallic objects, electrical equipment and cords.
FM antenna: Extend fully in a T-shape. If reception is poor, connect an optional outdoor antenna to the FM 75 Ω terminals. Be sure to connect the shield braid of the antenna to the 2 terminal.
AM antenna: Rotate to find the best reception.
Remote control
While sliding the latch, pull out the battery holder from the bottom of the remote control. Place the supplied battery on the battery holder with correct polarity. Finally, insert the holder back into position.
CR2025
•Replace the battery with new one when the operational distance between the remote control and main unit becomes shorter.
•Remove the battery if the unit is not going to be used for an extended period of time.
•The remote control may not operate if it is used under intense sunlight or if its line of sight is obstructed.
Caution!
•Do not keep the battery near metallic objects such as rings, bracelets, and keys. It may cause the battery to short circuit.
•After removing the battery, be sure to keep it out of reach of children. In case it is swallowed, consult a doctor immediately.
4
PARTS AND CONTROLS
Main unit: rear
|
AUX/VIDEO IN jacks |
|
|
Accept analog sound signals from external equipment. |
|
1 |
Connect external equipment using an optional connecting |
|
2 |
cable with RCA phono plugs (red plug to the R jack, white |
|
plug to the L jack). Refer also to the operating instructions |
||
|
||
3 |
for your equipment. |
|
|
To switch function to external input, press FUNCTION |
|
|
repeatedly to select the AUX (VIDEO or TV) function. |
|
4 |
Tip: |
|
5 |
To change a source name in the display, hold down g |
|
and press POWER while the power is on. |
||
|
||
|
AUX → VIDEO → TV |
|
6 |
|
|
|
2 DIGITAL OUT (OPTICAL) jack |
|
|
CD digital sound signals can be output through this jack. |
|
1 LINE OUT jacks |
Use an optical cable to connect digital audio equipment. |
|
Remove the dust cap from the DIGITAL OUT (OPTICAL) |
||
Analog sound signals for CD or radio can be output |
jack. Then connect an optical cable plug to the DIGITAL |
|
through these jacks. Use a cable with RCA phono plugs |
OUT (OPTICAL) jack. |
|
to connect audio equipment. |
When you record the sound signals of this unit with digital |
|
Connect the red plug to the R jack, and the white plug to |
audio equipment (MD recorder, CD recorder, etc.) |
|
the L jack. |
connected to this jack, the beginning of the first track |
|
Signals input through the AUX/VIDEO IN jacks are not |
may not be recorded. |
|
output from the LINE OUT jacks. |
|
3AM LOOP jack and FM 75 Ω terminals
Plug in the supplied AM and FM antennas.
4SUPER WOOFER3jack
Connect an optional powered sub woofer with a built-in |
En |
amplifier to this jack. |
5SPEAKERS3terminals
Connect the supplied speakers using the supplied speaker cords.
6AC power cord
5
Loading...