Aiwa XP-R207 User Manual

Size:
1.77 Mb
Download

dc

XP-R207

COMPACT DISC PLAYER

OPERATING INSTRUCTIONS

8A-HC1-941-01

000824AYO-OXA Printed in Hong Kong

A

AA (LR6) × 2

B

OWNER’S RECORD

For your convenience, record the model number and the serial number (you will find it on the bottom of your set) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty.

Model No.

Serial No.

NOTE

FOR USE IN THE U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may void the user’s right or authority to operate this product.

Highlighted letters in the text of this manual correspond to the illustrations.

PRECAUTIONS

To maintain good performance

Do not use the unit in places which are extremely hot, cold, dusty or humid. In particular, do not use or keep the unit in following places.

in a high humidity area such as a bathroom

near a heater

in an area exposed to direct sunlight (e.g., inside a parked car, where it can become extremely hot)

near sources of strong magnetism, such as televisions, speakers, or magnets

where there is a lot of movement or vibration, such as on a car dashboard or an unstable shelf

For safety

Do not attempt to disassemble the unit. Laser rays from the optical pickup are dangerous to the eyes.

Make sure that pins or other foreign object do not get inside the player.

Take care not to drop the unit or subject it to strong shocks.

To keep dust from the pickup lens, keep the disc compartment lid closed after use. Never touch the lens.

If you hear no sound when playing a disc, DO NOT turn the volume up high because music could suddenly start at high volume. Turn the volume control to the lowest level before starting playback and slowly turn it up to the desired level.

Note on listening with the headphones

Listen at moderate volumes to avoid hearing damage.

Do not wear the headphones while driving or cycling. It may create a traffic hazard.

You should use extreme caution or temporarily discontinue use in potentially hazardous situations, such as walking, jogging, etc.

Wear them properly; L is left, R is right.

Note on condensation

If the unit is suddenly moved from a cold place to a warm one, it may result in condensation on the pickup lens and malfunction or playback difficulties. Should this occur, leave the unit for a few hours, then try to playback again.

USING ON DRY CELL BATTERIES A

Open the battery compartment and insert two size AA (LR6) alkaline batteries with the0and9marks correctly aligned.

Battery replacement

OPE/BATT indicator changes from F (green) to M (orange) to E (red) according to the remaining power of the batteries. Replace the batteries when E (red) lights. If the unit remains in use after E (red) lights, “Lo-bAtt”appears and operation stops.

Battery life (using alkaline batteries LR6)

The setting of the E•A•S•S switch

Battery life

48

Approx. 20 hours

12

Approx. 19 hours

OFF

Approx. 15 hours

Battery life may vary depending on conditions of use.

If the cover of the battery compartment comes off B

B

hazard.

You should use extreme caution or temporarily discontinue use in potentially hazardous situations, such as walking, jogging, etc.

Wear them properly; L is left, R is right.

Note on condensation

If the unit is suddenly moved from a cold place to a warm one, it may result in condensation on the pickup lens and malfunction or playback difficulties. Should this occur, leave the unit for a few hours, then try to playback again.

USING ON DRY CELL BATTERIES A

Open the battery compartment and insert two size AA (LR6) alkaline batteries with the0and9marks correctly aligned.

Battery replacement

OPE/BATT indicator changes from F (green) to M (orange) to E (red) according to the remaining power of the batteries. Replace the batteries when E (red) lights. If the unit remains in use after E (red) lights, “Lo-bAtt”appears and operation stops.

Battery life (using alkaline batteries LR6)

The setting of the E•A•S•S switch

Battery life

48

Approx. 20 hours

12

Approx. 19 hours

OFF

Approx. 15 hours

Battery life may vary depending on conditions of use.

If the cover of the battery compartment comes off B

Note on dry cell batteries

Make sure that the 0and 9marks are correctly aligned.

Do not mix the different types of batteries, or an old battery with a new one.

To prevent the risk of electrolyte leakage or explosions, never recharge the batteries, apply heat to them, or take them apart.

When not using the batteries, remove them to prevent needless battery wear.

If liquid leaks from the batteries, wipe thoroughly to remove.

C

1

2

3

 

 

D

 

 

E

 

F

1

2

3

G

USING ON RECHARGEABLE BATTERIES C

Be sure to use size AA Ni-Cd1.2 V 700 mAh rechargeable batteries, which are commercially available.

Be sure to read the instructions of the purchased rechargeable batteries before use.

When using on rechargeable batteries for the first time, charge them until the battery indicator goes out.

Before charging the batteries, close the disc compartment. You cannot charge the batteries while it is opened.

1Insert the rechargeable batteries with the 0 and9 marks correctly aligned.

2Connect the AC adaptor.

1 to DC 5 ~ 6 V jack

2 to a wall outlet

3Keep sSTOP/OFF/CHARGE pressed for about 1 second to start charging.

“C-On”appears, and OPE/BATT indicator blinks.

When charging is completed, “C-OFF”flashes a few times, and OPE/BATT indicator goes out.

After charging, disconnect the AC adaptor.

Time to recharge the batteries

Recharge the batteries when E (red) lights. If the unit remains in use after E (red) lights, “Lo-bAtt”appears and the current operation stops.

To stop charging

Press sSTOP/OFF/CHARGE during charging.

ATTENTION:

The product you have purchased can be powered by nickel cadmium batteries which is recyclable. At the end of their useful life, under various state and local laws, it is illegal to dispose of these batteries into your municipal waste stream.

Please call 1-800-289-2492for information on how to recycle these batteries.

USING ON AC HOUSE CURRENT

Connect the supplied AC adaptor in the same way as when recharging the batteries.

During operation on AC house current, all of OPE/BATT indicators light.

BEFORE PLAYBACK

HOLD switch D

Release the HOLD switch before playback. → a

When not using the unit, set the HOLD switch to the HOLD position. → b Accidentally pressed button will not function.

If buttons are pressed when the HOLD switch is set to the HOLD position, “HOLd” flashes in the display.

Turning on and off D

Turning the power on

Press ePLAY/PAUSE. Power is turned on and playback starts.

Note

“Err” appears on the display when you play a disc placed upside-downor a defective disc.

Turning the power off

If no new operations are done within 30 seconds from the end of last operation, the power is turned off automatically. (Auto power off function)

You can turn off the power by pressing sSTOP/OFF/CHARGE before it is automatically turned off.

Standby mode D

When an operation finishes, the unit goes into standby mode until the auto power off function automatically turns off the power.

To enter standby mode, press ePLAY/PAUSE to start playback, then press sSTOP/OFF/CHARGE.

Adjusting the sound E

Volume

Turn the VOL control to adjust the volume.

DSL

Press DSL repeatedly for more powerful sound and deeper bass. : Deep bass is emphasized.

: Deep bass is strongly emphasized. : Normal sound

Signal sound function

You can check the operation by beep sound when you press an operation button. The signal sound function is not activated when you purchase this unit.

To use the signal sound function, press ePLAY/PAUSE while pressing PLAY MODE while in stop mode. The beep sound is heard when you press a button.

To cancel the beep sound, repeat this procedure.

F

1

2

3

G

 

defective disc.

Turning the power off

If no new operations are done within 30 seconds from the end of last operation, the power is turned off automatically. (Auto power off function)

You can turn off the power by pressing sSTOP/OFF/CHARGE before it is automatically turned off.

Standby mode D

When an operation finishes, the unit goes into standby mode until the auto power off function automatically turns off the power.

To enter standby mode, press ePLAY/PAUSE to start playback, then press sSTOP/OFF/CHARGE.

Adjusting the sound E

Volume

Turn the VOL control to adjust the volume.

DSL

Press DSL repeatedly for more powerful sound and deeper bass.

: Deep bass is emphasized.

: Deep bass is strongly emphasized. : Normal sound

Signal sound function

You can check the operation by beep sound when you press an operation button. The signal sound function is not activated when you purchase this unit.

To use the signal sound function, press ePLAY/PAUSE while pressing PLAY MODE while in stop mode. The beep sound is heard when you press a button. To cancel the beep sound, repeat this procedure.

Inserting a disc F

1Slide the OPEN switch to open the disc compartment.

2Place a disc in the center with the label side facing up.

3Close the disc compartment.

To remove the disc G

Pick up the disc, holding its edge, while pressing the pivot gently.

Note

The unit may not play a CD-R/RWdisc that is recorded on personal computers or some kinds ofCD-R/RWrecorders because of differences in recording platforms.

Do not attach any seal or label to either side (the recordable side or the labeled side) of a CD-R/RWdisc. It may cause malfunction.

XP-R207(AU) E Page 1

H

 

1

2

3

 

I

 

 

ENTER/DISP

 

V

 

V

J

 

 

V

 

V

K

 

PLAYBACK H

Connect the supplied headphones to the PHONES/LINE OUT jack.

1Release HOLD.

2Place a disc.

3Press ePLAY/PAUSE.

Playback starts from the first track. a track number

b elapsed playing time

Basic operation

To stop

Press sSTOP/OFF/CHARGE.

To pause

Press ePLAY/PAUSE.

 

To resume, press it again.

To search for the beginning of a track

Press ror t.

To locate a desired passage

Keep ror tpressed.

 

Release the button at the start of desired

 

passage.

Display during playback I

 

Press ENTER/DISP during playback to change the display as follows.

1 Track display and elapsed playing time (normal display)

V

2 Track display and remaining playing time of the track in play

V

3 Remaining number of tracks and remaining playing time

The time is not displayed in following cases.

When trying to program tracks beyond No.32.

When the total remaining time of the programmed tracks is over 100 minutes.

E•A•S•S PLUS (Electronic Anti-ShockSystem)J

The E•A•S•S PLUS function reduces skipping or muting of the sound when the unit is subjected to shocks.

The player keeps about 48 seconds or 12 seconds of playback sound in its memory.

To keep 48 seconds in the memory, set the E•A•S•S switch to 48. To keep 12 seconds in the memory,set the E•A•S•S switch to 12.

To cancel the E•A•S•S PLUS function, set the E•A•S•S switch to OFF.

Note

Before jogging with this unit, allow sufficient time for the memory buffer to fill up completely (ideally 40 to 48 seconds).

Continuous shock or vibration may cause the sound to be interrupted even if the E•A•S•S PLUS function is activated. This is normal and not a malfunction. Should you experience an interruption in sound, stabilize the unit for a few seconds, then resume your activity.

When the E•A•S•S switch is slid during playback, the unit will pause for about 2 seconds.

When you set the E•A•S•S switch to the 12 or OFF position, the quality of the sound will be better than the case that you set it to the 48 position.

Resume function K

Set the HOLD switch to RESUME.

appears, and you can start playback from the point where you stopped playback by pressing sSTOP/OFF/CHARGE.

When the resume function is on, all-trackrepeat is selected automatically.

To cancel resume play, set the HOLD switch to OFF.

Note

Resume play may start at a point about 30 seconds behind or ahead the stopped point. Resume play may not operate if you stopped at the last 30 seconds of the final track.

Resume play will be canceled if you open the disc compartment. If the unit is turned off, resume play will not be canceled. In this case, be sure to set the HOLD switch to OFF before changing discs.

Random play K

Press PLAY MODE while in standby mode to display.

Tracks on the disc are played in random order.

To cancel random play, press PLAY MODE while in standby mode. display changes to .

Note

You cannot back to previous track by pressing rduring random play.

You cannot select one-trackrepeat during random play.

Repeat play K

Press PLAY MODE during playback to select repeat play as follows.

: one-trackrepeatB

V

: all-trackrepeat

V

no repeat play (normal play)

V

V

K

L

1 ENTER/DISP

2

3 ENTER/DISP

5

Note

Resume play may start at a point about 30 seconds behind or ahead the stopped point. Resume play may not operate if you stopped at the last 30 seconds of the final track.

Resume play will be canceled if you open the disc compartment. If the unit is turned off, resume play will not be canceled. In this case, be sure to set the HOLD switch to OFF before changing discs.

Random play K

Press PLAY MODE while in standby mode to display.

Tracks on the disc are played in random order.

To cancel random play, press PLAY MODE while in standby mode. display changes to .

Note

You cannot back to previous track by pressing rduring random play.

You cannot select one-trackrepeat during random play.

Repeat play K

Press PLAY MODE during playback to select repeat play as follows.

: one-trackrepeatB

V

: all-trackrepeat

V

no repeat play (normal play)

PROGRAM PLAY L

Up to 24 tracks can be chosen for program play.

1Press ENTER/DISP while in standby mode to display.

2Select the desired track by pressing randt.a track number

b program number

3Press ENTER/DISP within 8 seconds.

If it is not pressed within 8 seconds, the track number changes to 00. Repeat the procedure from step 2 again.

4Repeat steps 2 and 3 to program more tracks.

5Press ePLAY/PAUSE to start program play.

To stop program play

Press sSTOP/OFF/CHARGE.

To add tracks to the program

Repeat steps 2 and 3 before you proceed to step 5. You can add tracks to the end of the program.

To erase the program

Press sSTOP/OFF/CHARGE while in standby mode.

To check the programmed tracks

Press ENTER/DISP repeatedly before you proceed to step 5.

The number of each programmed track will be displayed in order of playback.

Note

The program is also erased when the disc compartment is opened or the auto power off function turns the power off.

When 24 tracks are programmed, “P-FULL”appears, and no more tracks may be added.

You cannot back to the previous track by holding rpressed during program play.

Repeat play and random play can be performed during program play.

M

1

2

N FM

AM

 

 

O

AM STEP 9kHz

10kHz

P

1

2

3ENTER/DISP

Q

RADIO RECEPTION

Tuning in to a station M

1Press TUNER ON/BAND repeatedly to select AM or FM.

2Press TUNING +(t) or-(r)to tune in to a station.

After listening, press sSTOP/OFF/CHARGE to turn off the radio.

For quick tuning

Keep either TUNING +(t) or -(r)pressed for about 1 second. When a station is tuned in to, the frequency stops automatically. However, it does not stop if the broadcast signal is weak.

For better reception N

FM: The headphone cord functions as the FM antenna. Keep it extended. AM: Turn the unit to find the position which gives the best reception.

To listen to an FM stereo broadcasting

When a tuned in station is in stereo, ST changes to .

When the FM stereo signal is weak and distorted, press MONO/ST. ST goes out and the sound will be heard in monaural but distortion will be reduced.

Note

Do not open the disc compartment during radio reception. The buttons will be deactivated.

The power is turned off automatically if no operation is made after 180 minutes from the last operation during radio reception.

AM steps O

Radio broadcasts have different frequency ranges and changes in different steps in different countries.

This unit is factory-setto 10 kHz steps on AM. When using the unit where the AM step changes to 9 kHz, set the AM STEP switch on the inner side of the disc compartment to 9 kHz.

• When the AM step is changed, stations that you preset are erased.

Presetting stations P

You can preset up to total of 30 stations on AM and FM.

1Press TUNER ON/BAND repeatedly to select AM or FM.

2Press TUNING +(t) or-(r)to tune in to a station.

3Press ENTER/DISP to preset the station. a Preset number

To preset more stations, repeat steps 2 and 3.

Listening to preset stations Q

1Press TUNER ON/BAND repeatedly to select AM or FM.

2Press PRESET CALL i/krepeatedly to select the preset number.

After listening, press sSTOP/OFF/CHARGE to turn off the radio.

Changing the presetting

1Press PRESET CALL i/k repeatedly to select the preset number you wish to change.

2Keep ENTER/DISP pressed for 1 or more seconds until the preset number and the frequency flash.

3While the preset number is flashing, press TUNING +(t) or-(r)to tune in to a station.

4Press ENTER/DISP to preset the station on the selected preset number.

If the flashing stops, repeat the procedure from step 2.

Erasing the presettings one by one

Press sSTOP/OFF/CHARGE after step 2 in “Changing the presetting” above. Each preset station is erased. All the settings move up by one and the preset numbers are refreshed.

Erasing all of the presetting

Keep ENTER/DISP pressed, then press TUNER ON/BAND when the frequency and preset number starts flashing.

CONNECTING TO AN EXTERNAL UNIT R

Use a commercially available connection cord which has a 3.5 ø stereo miniplug at one end and two phono plugs at the other end.

Connect the stereo mini-plugto the PHONES/LINE OUT jack of the unit and connect the phono plugs to the analog input terminals of the external unit.

Note

Turn off the power of both units before connection.

DO NOT connect to the PHONO inputs of an amplifier (with a built-inphonoequalizer-amplifier).

Adjust the volume and DSL on this unit.

MAINTENANCE

To clean the lens S

If the lens becomes dirty, the player will skip or not play. If this occurs, clean the lens in the following manner.

To remove dust or dry particles, first use a camera lens blower/brush a to blow a few times to loosen particles, then gently brush the lens b clean. Finish by blowing the lens again.

To remove fingerprints use a cotton swab dipped in lens cleaning solution Wipe

1

2

3ENTER/DISP

Q

R

S

T

Each preset station is erased. All the settings move up by one and the preset numbers are refreshed.

Erasing all of the presetting

Keep ENTER/DISP pressed, then press TUNER ON/BAND when the frequency and preset number starts flashing.

CONNECTING TO AN EXTERNAL UNIT R

Use a commercially available connection cord which has a 3.5 ø stereo miniplug at one end and two phono plugs at the other end.

Connect the stereo mini-plugto the PHONES/LINE OUT jack of the unit and connect the phono plugs to the analog input terminals of the external unit.

Note

Turn off the power of both units before connection.

DO NOT connect to the PHONO inputs of an amplifier (with a built-inphonoequalizer-amplifier).

Adjust the volume and DSL on this unit.

MAINTENANCE

To clean the lens S

If the lens becomes dirty, the player will skip or not play. If this occurs, clean the lens in the following manner.

To remove dust or dry particles, first use a camera lens blower/brush a to blow a few times to loosen particles, then gently brush the lens b clean. Finish by blowing the lens again.

To remove fingerprints, use a cotton swab dipped in lens cleaning solution. Wipe gently from the center to the edge. Lens cleaning solution is commercially available.

Note

Take care not to get too much solution on the swab, which could flow into the unit and cause damage.

Pressing too strongly with the swab could scratch or break the lens.

To clean the discs T

Before playing, wipe the disc from the center outward with a cleaning cloth. After playing, store the disc in its case.

SPECIFICATIONS

Tracking system

3-beamlaser

Laser pickup

Semiconductor laser

D/A conversion

4-timesoversampling digital filter +1-bitDAC

Frequency response

20 – 20,000 Hz (47 k ohms)

Output

PHONES/LINE OUT jack (stereo mini-jack)

Frequency range

AM: 530/531 kHz – 1,710/1,602 kHz

 

(10 kHz/9 kHz steps)

Maximum output

FM: 87.5 – 108 MHz

12 mW + 12 mW (16 ohms at 1 kHz)

Power supply

500 mV (47 k ohms at 1 kHz)

DC 3 V using two size AA (LR6) alkaline

 

batteries

 

DC 2.4 V using two commercially available

 

(Ni-Cd1.2 V 700 mAh) rechargeable batteries

 

AC house current using the supplied AC adaptor

Maximum outside dimensions

 

128 (W) × 31.2 (H) × 129.5 (D) mm (excluding

 

projecting parts and controls)

Weight

(5 1/8 × 11/4 × 51/8 in.)

Approx. 225 g (7.9 oz.) excluding batteries

Accessories

AC adaptor AC-D603(1)

AC adaptor AC-D603U

Stereo headphones (1)

Rated input: AC 120 V, 60 Hz

The specifications and external appearance of this unit are subject to change without notice.

XP-R207(AU) E Page 2

d

Las letras subrayadas a lo largo de este manual corresponden a las mismas

letras en las figuras.

XP-R207

COMPACT DISC PLAYER

REPRODUCTOR DE DISCOS COMPACTOS

INSTRUCCIONES DE MANEJO

8A-HC1-942-01

000824AYO-OXA Printed in Hong Kong

A

AA (LR6) × 2

B

PRECAUCIONES

Para mantener buenas prestaciones

No utilice el aparato en lugares muy calientes, fríos o húmedos. Especialmente, no utilice o instale el aparato en los siguientes lugares.

en lugares muy húmedos como en el baño

cerca de la calefacción

en un lugar expuesto a los rayos del sol (por ejemplo en un coche estacionado donde puede calentarse mucho)

cerca de fuentes magnéticas fuertes, por ejemplo televisores, altavoces o imanes

donde hay mucho movimiento o vibración, sobre el cubretablero del coche o en un estante poco estable

Para su seguridad

No trate de desarmar el aparato. Los rayos láser del receptor óptico son peligrosos para los ojos.

Compruebe que los pasadores u otras materias extrañas no entren en el reproductor.

No deje caer el aparato ni exponga a un golpe fuerte.

Para no ensuciar la lente del receptor con polvo cierre la tapa del compartimiento del disco después de usar. No toque la lente.

Si no se escucha el sonido durante la reproducción de un disco. NO levante el volumen porque la música puede empezar a un volumen alto. Gire el control de volumen a su nivel más bajo antes de empezar a reproducir y gire lentamente hasta subir al volumen deseado.

Notas para escuchar con los auriculares

Escuche a un volumen bajo para no dañar sus oídos.

No escuche con los auriculares cuando ande en bicicleta. Puede ser un peligro para el tráfico.

Se debe tener mucho cuidado o dejar se utilizar temporalmente en casos potencialmente peligrosos, por ejemplo cuando camina, corre, etc.

Utilice correctamente, L para el izquierdo y R para el derecho.

Nota sobre la condensación

Si se lleva el aparato repentinamente de un lugar frío a uno caliente puede condensarse la humedad en la lente del receptor y puede funcionar mal o tener problemas en la reproducción.

En este caso, deje descansar el aparato unas horas y trate de volver a reproducir.

FUNCIONAMIENTO CON PILAS A

Abra el portapilas y coloque dos pilas alcalinas tamaño AA (LR6) con las marcas0y9correctamente alineadas.

Cambio de las pilas

El indicador OPE/BATT cambia de F (verde) a M (naranja) a E (rojo) según la carga de las pilas. Cambie las pilas cuando se enciende la luz E (rojo). Si se sigue utilizando el aparato después de que se encienda la luz E (rojo), aparece “Lo-bAtt”y deja de funcionar.

Vida de las pilas (con pilas alcalinas LR6)

El ajuste del interruptor E•A•S•S

Vida de las pilas

48

Aprox. 20 horas

12

Aprox. 19 horas

OFF

Aprox. 15 horas

La vida de las pilas depende de la forma de utilizar el aparato.

Si se sale la tapa del portapilas B

Notas sobre las pilas

Compruebe que las marcas 0y 9están correctamente alineadas.

No mezcle diferentes tipos de pilas o una pila nueva con otra vieja.

Para que no haya fugas de electrólito o explosión no cargue las pilas, caliente o desarme.

Cuando no utilice las pilas, sáquelas para evitar que se gasten inútilmente.

Si se produce una fuga del líquido de las pilas, limpie a fondo para sacarlas.

B

La vida de las pilas depende de la forma de utilizar el aparato.

Si se sale la tapa del portapilas B

Notas sobre las pilas

Compruebe que las marcas 0y 9están correctamente alineadas.

No mezcle diferentes tipos de pilas o una pila nueva con otra vieja.

Para que no haya fugas de electrólito o explosión no cargue las pilas, caliente o desarme.

Cuando no utilice las pilas, sáquelas para evitar que se gasten inútilmente.

Si se produce una fuga del líquido de las pilas, limpie a fondo para sacarlas.