Aiwa BMZ-K1 User Manual
Size:
681.83 Kb
Download

4-246-647-02 (1)

Mini Hi-FiComponent System

BMZ-K1/BMZ-K2

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Do not install the appliance in a confined space, such as a bookcase or built-incabinet.

To prevent fire, do not cover the ventilation of the apparatus with newspapers, table-cloths,curtains, etc. And don't place lighted candles on the apparatus.

En

To prevent fire or shock hazard, do not place objects filled

with liquids, such as vases, on the apparatus.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

“CAUTION:TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLEPARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

The use of optical instruments with this product will increase eye hazard.

If you have any questions about this product, you may call; sony customer Information Center 1-800-488-7669.This Number below is for the FCC related matters only.

Regulatory Information

Declaration of Conformity

Trade name:

SONY

Model No.:

BMZ-K1/BMZ-K2

Responsible Party:

Sony Electronics Inc.

Address:

680 Kinderkamack Road, Oradell,

 

NJ, 07649 USA

Telephone No.:

201-930-6972

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

PRECAUTIONS

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

On operating voltage

Before operating the system, check that the operating voltage of your system is identical with the voltage of your local power supply.

2

On safety

The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

Unplug the system from the wall outlet (mains) if it is not to be used for an extended period of time. To disconnect the cord (mains lead), pull it out by the plug. Never pull the cord itself.

Should any solid object or liquid fall into the component, unplug the stereo system and have the component checked by qualified personnel before operating it any further.

The AC power cord must be changed only at a qualified service shop.

On placement

Place the unit in a location with adequate ventilation to prevent heat build-upthe unit.

Do not place the unit in an inclined position.

Do not place the unit in locations where it is;

-Extremely hot or cold

-Dusty or dirty

-Very humid

-Vibrating

-Subject to direct sunlight.

On heat buildup

Although the unit heats up during operation, this is not malfunction.

Place the unit in a location with adequate ventilation to prevent heat build-upin the unit.

If you continuously use this unit at a large volume, the cabinet temperature of the top, side and bottom rises considerable. To avoid burning yourself, do not touch the cabinet.

On operation

If the system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the CD player. Should this occur, the system will not operate properly. Remove the CD and leave the system turned on for about an hour until the moisture evaporates.

When you move the system, take out any discs.

Notes on discs

•Playable discs on this unit are Audio CDs (CDs), CD-R/CD-RWwith audio data(CD-R/RW)andCD-R/CD-RWwith MP3 files(MP3-CDs).

•Discs recorded on CD-R/RWdrives may not be played back because of scratches, dirt., recording condition or the drive's characteristics.

•CD-R/RWdiscs which are not finalized at the end of recording cannot be played back.

•Do not attach adhesive label, etc. to either side of a CD-R/RW disc, as doing so may cause malfunction.

•Do not load an unrecorded CD-R/RWdisc. The disc may be damaged.

Do not insert 8-cm (3-inch) discs. Those discs cannot be played on this unit. Moreover, if you insert the discs of that

size forcibly, you may not be able to eject it.

•Discs with non-standardshapes (e.g., heart, square, star) cannot be played on this unit. Attempting to do so may damage the unit. Do not use such discs.

•DVD, SACD, CD-ROMand VCD cannot be played on this unit.

Music discs encoded with copyright protection technologies

This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

If you have any questions or problems concerning your stereo system, please consult your nearest Aiwa dealer.

TABLE OF CONTENTS

 

PREPARATIONS ...................................

4

PARTS AND CONTROLS .........................

5

ADJUSTMENTS BEFORE OPERATION ..........

8

SOUND ADJUSTMENTS ..........................

9

CD OPERATIONS ................................

10

MP3-CDOPERATIONS .........................

13

TUNER OPERATIONS ...........................

15

TIMER OPERATIONS ...........................

16

CONNECTING A PERSONAL COMPUTER ....

18

REFERENCE .....................................

21

En

3

PREPARATIONS

Connection

Plug in the AC power cord to the AC outlet after all other connections are made.

1Connect the speaker cords to the speakers.

Connect the gray cords to the + terminals and the cords with black stripes to the - terminals.

3Connect the supplied antennas.

Connect the FM antenna to the FM 75 Ω terminal and the AM antenna to the AM LOOP jack.

AM antenna

En

2Connect the speakers to the main unit.

Connect the right speaker (marked with “R”) to the SPEAKERS R terminals and place it on the right side of the unit. Connect the left (marked with “L”) to the SPEAKERS L terminals and place it on the left side. The speaker cords with the black stripes go to the 9terminals.

FM antenna

4Connect the AC power cord to an AC outlet.

When the AC power cord is connected to a wall outlet for the first time, DEMO appears in the display.

To deactivate the DEMO, press TITLE.

Speakers

•Do not short-circuitthe 0and 9speaker cord leads. •Do not leave objects generating magnetism or objects

affected by magnetism near the speakers.

Antennas

Keep antennas away from metallic objects, electrical equipment and cords.

FM antenna: Extend fully and position for the best

reception. If reception is poor, connect an optional outdoor antenna to the FM 75 Ω terminal. Note that, when connecting an optional outdoor antenna, use an adaptor as required.

AM antenna: Rotate to find best reception.

Remote commander

Detach the battery compartment lid at the rear of the remote commander and insert two R6 (size AA) batteries with correct polarity.

R6(AA)

•Replace the batteries with new ones when the operational distance between the remote commander and main unit becomes shorter.

•Remove the batteries if the unit is not going to be used for an extended period of time.

•The remote commander may not operate if it is used under intense sunlight or if its line of sight is obstructed.

4

PARTS AND CONTROLS

Main unit: front

6

PLAY MODE (11-14)

# TITLE (13, 20)

 

Refer to the pages indicated in parentheses for details.

 

Selects various CD play mode.

When the unit is turned off: activates or deactivated

 

TUNING DOWNf/r, UPg/t

DEMO.

 

7

 

Changes the display in MP3-CDor USB source.

 

 

(8-11,13, 15, 16)

 

 

 

 

@

1

 

2

#

3

$

 

4

%

5

^

6

7

 

8

&

9

*

 

0

 

!

 

1POWER 6STANDBY/ON (8, 15, 16)

Switches the unit on and off (standby).

2FUNCTION (10, 13, 18, 20)

Switches the active function among CD, USB, TUNER, VIDEO and AUX.

3BAND (8, 15)

Select tuner function and the tuner band.

4GEQ (9)

Selects a sound equalization curve.

i-Bass(9)

Produces rich and clear low frequency sound.

5TREBLE/MIDDLE (9)

Adjusts the treble or middle range level.

BASS (9)

CD: skips to a previous or a succeeding track when pressed, searches a track in fast forward or reverse playback when held down.

Tuner: manually tunes up or down within the band.

8USB terminal

Accepts sound signals from a personal computer. Connect your personal computer to this terminal with a USB cable so that the unit can output the sound of an audio file which is played back by the Winamp3 on your computer.

Be sure to see “CONNECTING A PERSONAL COMPUTER” on page 18 for the details about the computer requirements, how to connect and so on before actually connecting your computer.

9LINE IN (VIDEO/AUDIO) jacks

Accepts analog signals from external equipment. Connect using an optional connecting cable with RCA phono plugs (red plug to R jack, white plug to L jack, yellow plug to VIDEO jack).

Refer also to the operating instructions of your equipment. To switch function to external input, press FUNCTION repeatedly to display “VIDEO”.

0zEJECT (8, 10, 11, 13)

Ejects the disc(s).

!DISC SELECT (8, 10, 13)

Selects a disc slot.

Starts CD play for one desired disc.

@VOLUME (9)

Adjusts the volume.

DISPLAY (8)

Changes the display in CD playback mode.

Turns the back light on and off when the unit is turned off.

MODE (8, 9)

Selects various modes (sound adjustment, etc.) when used in combination with ENTER and MULTI JOG. Switches the ECO mode on and off when the unit is turned off.

$ aPAUSE/SET (10, 15)

En

Pauses CD play.

sSTOP/CLEAR(10-13)

Stops CD play.

cPRESET (10, 11,13-15)

Starts CD play.

%MULTI JOG (8-11,13, 15, 16)

When used in combination with ENTER and MULTI JOG, CD: selects a track.

Tuner: selects a preset station.

^ENTER (8, 9, 15, 16)

Fixes the modes and the time (clock and timer, etc.) when used in combination with ENTER and MULTI JOG.

&PHONES jack

Plug in optional headphones set with a stereo mini plug ( 3.5 mm). Speaker output is canceled.

*ALBUM/PLAY LIST k,i(13, 20)

Skips to a previous or succeeding album or play list.

Adjusts the bass level.

5

Main unit: rear

Refer to the pages indicated in parentheses for details.

1

2

3 4

En

5

6

1AM LOOP jack and FM 75 terminal (4)

Plug in the supplied AM and FM antennas.

2AUX (MD) IN jacks

Accept analogue sound signals from external equipment. Connect external equipment using an optional connecting cable with RCA phono plugs (red plug to R jack, white plug to L jack). Refer also to the operating instructions for your equipment.

To switch function to external input, press FUNCTION repeatedly to display “AUX”.

3AUX (MD) OUT jacks

Analog sound signals for all functions can be output through these jacks. Use a cable with RCA phono plugs to connect audio equipment.

Connect the red plug to the R jack, and the white plug to the L jack.

However, the signal is not output when the function is “VIDEO” or “AUX”.

4VIDEO OUT

Signals from VIDEO IN jack output through this jack.

5#SPEAKER terminals (4)

Connect the speaker cords of the supplied speakers.

6AC power cord (4)

6

Remote commander

Refer to the pages indicated in parentheses for details.

18

2

9

3

4

0

5

!

6

@

 

7

 

Buttons with the same or similar names on the main unit basically have the same function.

1POWER (8, 16)

21-9,0/10,+10 (10, 11, 13, 15)

CD: selects a track of the specified number.

Tuner: tunes in the station with the specified preset number.

The numbered buttons take on these functions when pressed with SHIFT held down.

BAND (8, 15)

SPECTRUM (8)

Changes the spectrum analyser display.

TUNER MODE (15)

Switches between stereo or monaural FM reception.

GEQ (9)

3c/d(10, 11, 13, 14)

Starts CD play. s(10-13) a(10, 15)

f/g(10, 15)

r/tPRESET(8-11,13, 15, 16)

Tuner: selects a preset station.

M/NALBUM (13)

Selects a previous or a succeeding album.

4PLAY MODE (11-14)

REPEAT (11)

Selects repeat CD playback mode.

5CLOCK/TIMER SET (8, 16)

Enters clock and timer setting mode.

CLOCK/TIMER SELECT (8, 16)

Switches timer setting on and off.

6DISPLAY (8)

SOUND (9)

Selects bass, treble or middle range level setting mode.

CLEAR (11)

Clears a track of the CD programed playback and a tuner preset station.

7SHIFT

Hold down when pressing a numbered button to change its function to that printed above the number.

8FUNCTION (10, 13, 18, 20)

9DISC SKIP (10, 13)

Changes a disc slot.

0 ENTER (8, 9, 15, 16)

!SLEEP (16)

Selects sleep-timermode.

@ VOLUME+,-(9)

En

Note

The buttons not explained above (EDIT andKARAOKE) do not operate for this unit.

7